IEC 61300-3-45-2011 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-45 Examinations and measurements.pdf

1、 IEC 61300-3-45 Edition 1.0 2011-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-45: Examinations and measurements Attenuation of random mated multi-fibre connectors Dispositifs dinterconnexion et

2、composants passifs fibres optiques Mthodes fondamentales dessais et de mesures Partie 3-45: Examens et mesures Affaiblissement d laccouplement de connecteurs quelconques multifibres IEC 61300-3-45:2011 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserve

3、d. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If yo

4、u have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette pu

5、blication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou

6、 si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The Interna

7、tional Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please m

8、ake sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on

9、 projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leadi

10、ng online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If

11、 you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisat

12、ion mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rc

13、ente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informatio

14、ns sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: w

15、ww.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en

16、 ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61300-3-45

17、 Edition 1.0 2011-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-45: Examinations and measurements Attenuation of random mated multi-fibre connectors Dispositifs dinterconnexion et composants pass

18、ifs fibres optiques Mthodes fondamentales dessais et de mesures Partie 3-45: Examens et mesures Affaiblissement d laccouplement de connecteurs quelconques multifibres INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE N ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-

19、88912-483-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 61300-3-45 IEC:2011 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references 5 3 General description . 5 3.1 Test methods 5 3.2 Precautions . 6 4 Apparatu

20、s . 7 4.1 Source (S) . 7 4.2 Launch conditions (E) 7 4.3 Detector (D). 7 5 Procedure . 8 5.1 Method 1 . 8 5.2 Method 2 . 10 5.3 Analysis of results . 13 6 Details to be specified . 13 Figure 1 “Reference” cord measurement Method 1 8 Figure 2 Test cord measurement Method 1 8 Figure 3 Test matrix and

21、labelling for measuring method 1 (2-fibre connector) . 9 Figure 4 Test matrix and labelling for measuring method 1 (4-fibre connector) 10 Figure 5 Test matrix and labelling for measuring method 1 (8, 10, 12-fibre connector). 10 Figure 6 “Reference” cord measurement (1) Method 2 . 11 Figure 7 Test co

22、rd measurement (1) Method 2 . 11 Figure 8 “Reference” cord measurement (2) Method 2 . 12 Figure 9 Test cord measurement (2) Method 2 . 12 Figure 10 Test matrix and labelling for measuring method 2 (2-fibre connector) 12 Figure 11 Test matrix and labelling for measuring method 2 (4-fibre connector) 1

23、3 Figure 12 Test matrix and labelling for measuring method 2 (8, 10, 12-fibre connector) . 13 Table 1 Sample size for Method 1. 6 Table 2 Sample size for Method 2. 6 61300-3-45 IEC:2011 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TES

24、T AND MEASUREMENT PROCEDURES Part 3-45: Examinations and measurements Attenuation of random mated multi-fibre connectors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National C

25、ommittees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Av

26、ailable Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental

27、 organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on techn

28、ical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IE

29、C National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unifor

30、mity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) I

31、EC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure

32、 that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any

33、 nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the refer

34、enced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Intern

35、ational Standard IEC 61300-3-45 Ed.1.0 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B/3177/FDIS 86B/3215/RVD Full

36、information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 4 61300-3-45 IEC:2011 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all parts of IEC 61300 series, published under the gen

37、eral title, Fibre optic interconnecting and passive components Basic test and measurement procedures, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.ie

38、c.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61300-3-45 IEC:2011 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-45: Examinatio

39、ns and measurements Attenuation of random mated multi-fibre connectors 1 Scope The purpose of this part of IEC 61300 is to describe the procedure required to measure the statistical distribution and mean attenuation for random mated optical connectors with physical contact (PC) and angled physical c

40、ontact (APC) polished 1-row multi-fibre rectangular ferrules as defined in the IEC 61754 series. This measurement method is applicable to cable assemblies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

41、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General and guidance IEC 61300-3-1, Fibre optic inte

42、rconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-35, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-35: Examinations and measurements Fibre

43、optic connector endface visual and automated inspection IEC 61754 (all parts), Fibre optic connector interfaces 3 General description 3.1 Test methods Two test methods are described for measuring the attenuation of random mated optical connectors. Both provide an estimate of the expected average per

44、formance that a group of cable assemblies (including an adaptor, if applicable) selected from a batch will exhibit when used in an optical system. The cable assemblies, and any adaptors, must be chosen at random to ensure that the measurements provide a statistically unbiased estimate. Method 1 desc

45、ribes the procedure using a sample of cable assemblies and adaptors specified in Table 1. In this case the plugs (with pins) are used as “reference” plugs and the plugs (without pins) are tested against them sequentially. The results, based on the number of measurements specified in Table 1, are rec

46、orded in the test matrix shown in Figures 3 to 5. Method 1 is intended to be part of a design approval exercise that may involve one or more suppliers. Once approval is achieved, Method 2 would be relied on to maintain process control. However, in the event of a dispute, Method 1 shall act as the re

47、ference measurement method. 6 61300-3-45 IEC:2011 Method 2 describes a procedure for the measurement of a sample of cable assemblies specified in Table 2. Three cable assemblies are selected from the sample as “reference” cable assemblies and pins are fitted. The other test cable assemblies (without

48、 pins) are tested against each of the three “reference cable assemblies” sequentially. This produces the number of measurements specified in Table 2 and the results are recorded in the test matrix shown in Figures 10 to 12. It is recognised that the number of measurements required by Method 1 may be

49、 excessive for day-to-day routine checking of either in-house or supplier produced products. In this case, as indicated above, Method 2 may be an alternative option. NOTE In this measurement method, the terms “reference” plug or “reference” cord are used to define those components chosen at random from a batch, against which a number of comparat