IEC 61300-3-46-2011 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-46 Measurement - Bore diameter f.pdf

1、 IEC 61300-3-46 Edition 1.0 2011-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-46: Measurement Bore diameter for guide pin in MT ferrules Dispositifs dinterconnexion et composants passifs fibres

2、optiques Mthodes fondamentales dessais et de mesures Partie 3-46: Mesure Diamtre dalsage pour broche de guidage dans les frules MT IEC 61300-3-46:2011 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no par

3、t of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyri

4、ght or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni u

5、tilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits su

6、pplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (I

7、EC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edi

8、tion, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced pub

9、lications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic an

10、d electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on

11、 this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des

12、 normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement pe

13、ut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publication

14、s retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictio

15、nnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/w

16、ebstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61300-3-46 Edition 1.0 2011-06 INTERNATIONAL ST

17、ANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-46: Measurement Bore diameter for guide pin in MT ferrules Dispositifs dinterconnexion et composants passifs fibres optiques Mthodes fondamentales dessais et de mesures

18、 Partie 3-46: Mesure Diamtre dalsage pour broche de guidage dans les frules MT INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE H ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-88912-536-4 Registered trademark of the International Electrotechnical Commission Marque

19、 dpose de la Commission Electrotechnique Internationale colour inside 2 61300-3-46 IEC:2011 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 General description 5 3.1 Pin specifications 5 3.2 Test conditions 6 3.3 Apparatus 6 4 Procedure 6 5 Post test examination . 8 6 Details to be sp

20、ecified 8 Figure 1 Gauge pin through ferrule 7 Figure 2 An example of a complete measurement apparatus with ferrule . 7 Figure 3 An example of front loading the pin in an assembled connector . 8 Table 1 Pin specifications 5 Table 2 Test conditions 6 61300-3-46 IEC:2011 3 INTERNATIONAL ELECTROTECHNIC

21、AL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-46: Measurement Bore diameter for guide pin in MT ferrules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprisin

22、g all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards

23、, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparato

24、ry work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizatio

25、ns. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of rec

26、ommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by

27、any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional p

28、ublication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by ind

29、ependent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for an

30、y personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normati

31、ve references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsi

32、ble for identifying any or all such patent rights. International Standard IEC 61300-3-46 has been prepared by subcommittee SC86B: Fibre optic interconnecting devices and passive components, of IEC technical committee TC86: Fibre optics. The text of this standard is based on the following documents:

33、CDV Report on voting 86B/3076/CDV 86B/3165/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 61300-3-46 IEC:2011 The committee

34、has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, o

35、r amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 61300-3-46 IEC:2011 5 FIBRE OPTIC I

36、NTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-46: Measurement Bore diameter for guide pin in MT ferrules 1 Scope The purpose of this part of IEC 61300 is to provide a standard for the measurement of guide pin bore diameters in thermoplastic and thermoset

37、MT ferrules specified in IEC 61754-5. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendment

38、s) applies. IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements, Visual examination. IEC 61754-5, Fibre optic connector interfaces - Part 5: Type MT connector family 3 General description 3.1 Pin spec

39、ifications See Table 1 for pin specifications. Table 1 Pin specifications Material Tungsten Carbide Steel Pin Diameter ranges (mm) 0,69 895 to 0,69 905 0,69 905 to 0,69 915 0,69 915 to 0,69 925 0,69 925 to 0,69 935 0,69 935 to 0,69 945 0,69 945 to 0,69 955 0,69 955 to 0,69 965 0,69 965 to 0,69 975 0

40、,69 975 to 0,69 985 0,69 985 to 0,69 995 0,69 995 to 0,70 005 Cylindricity 100,0 nm or better Surface finish 0,2 m 6 61300-3-46 IEC:2011 3.2 Test conditions See Table 2 for test conditions. Table 2 Test conditions Temperature (T) Relative Humidity (RH) Total Assembly Mass g 21,0 C to 25,0 C 50,0% RH

41、 10,0 % 100,0 +/- 5,0 g 3.3 Apparatus The apparatus shall include the following elements: Traceable, calibrated gauge pins of tungsten carbide steel, 0,698 95 mm to 0,700 05 mm in 100 nm increments; Pin vice with rod and platform to hold calibrated mass elements, the mass of which is sufficient to m

42、ake the entire assembly 100,0 g total. Fixturing should ensure that the assembly is free to hang vertically during testing. Both pins and test parts should be as clean as possible to ensure an accurate measurement. 4 Procedure Parts should be preconditioned using the conditions in 3.2 for a minimum

43、of 24 hours. Once conditioned, a calibrated gauge pin is pushed into the ferrule until it clears the ferrule end as shown in Figure 1. Start with a pin that should fit freely in the part under test. Rear entry is recommended where possible to reduce the risk of ferrule end face damage. (For fully as

44、sembled product, front entry may be used as an alternative to disassembly as shown in Figure 3.) After the pin engages the full bore ID length, the pin vice is secured to the calibrated gauge pin/ferrule vice assembly as shown in Figure 2. The mass is gradually released, pulling the pin through the

45、bore. This procedure is repeated using increasingly larger pins until the 100,0 g 5,0 g mass cannot freely pull the pin out of the bore. Once this state is reached, the previous pins diameter is recorded as the effective diameter of the guide pin bore. Repeat the above procedure for the opposite hol

46、e. 61300-3-46 IEC:2011 7 IEC 1208/11 Figure 1 Gauge pin through ferrule IEC 1209/11 Figure 2 An example of a complete measurement apparatus with ferrule 8 61300-3-46 IEC:2011 IEC 1210/11 Figure 3 An example of front loading the pin in an assembled connector 5 Post test examination After the test is

47、completed, visually examine the specimens in accordance with IEC 61300-3-1. Check for damage to the exit region of the guide pin bore breakage, chipping or scratching of the ferrule face 6 Details to be specified Test conditions Size range of pins used Final size of each bore _ 10 61300-3-46 CEI:201

48、1 SOMMAIRE AVANT-PROPOS 11 1 Domaine dapplication 13 2 Rfrences normatives . 13 3 Description gnrale 13 3.1 Spcifications des broches 13 3.2 Conditions dessais . 14 3.3 Appareillage 14 4 Procdure 14 5 Examen aprs essai . 16 6 Dtails spcifier . 16 Figure 1 Broche calibre travers la frule 15 Figure 2 Exemple dappareillage de mesure complet avec frule . 15 Figure 3 Exemple dinsertion de la broche sur le devant dans un connecteur assembl 16 Tableau 1 Spcifications des broches 13 Tableau 2 Conditions dessais . 14 61300-3-46 CEI:2011 11 COMMISSION LECTROTECHNIQUE INTERNATIONALE _ DI