IEC 61987-1-2006 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 1 Measuring equipment with ana.pdf

1、 IEC 61987-1 Edition 1.0 2006-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 1: Measuring equipment with analogue and digital output Mesure et commande dans les processus industriels Elments

2、et structures de donnes dans les catalogues dquipements de processus Partie 1: Equipement de mesure avec sortie analogique et numrique IEC 61987-1:2006 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2006 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this pub

3、lication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have a

4、n enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous q

5、uelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires

6、sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechn

7、ical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you h

8、ave the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on

9、projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leadin

10、g online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If y

11、ou wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tou

12、t ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles:

13、Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI

14、 - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectron

15、iques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner

16、des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61987-1 Edition 1.0 2006-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 1: Measuring equipm

17、ent with analogue and digital output Mesure et commande dans les processus industriels Elments et structures de donnes dans les catalogues dquipements de processus Partie 1: Equipement de mesure avec sortie analogique et numrique INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE

18、INTERNATIONALE X ICS 25.040.40; 35.240.50 PRICE CODE CODE PRIX ISBN 978-2-83220-375-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distribut

19、or. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61987-1 IEC:2006 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 7 2 Normative references 7 3 Terms and definitions . 7 4 Metadocuments 15 4.1 General . 15 4.2 Metadocument chapters and features 1

20、6 4.3 Nomenclature 18 5 Metadocument for process measuring equipment 18 5.1 Identification 18 5.2 Application. 19 5.3 Function and system design . 19 5.4 Input 20 5.5 Output . 20 5.6 Performance characteristics 21 5.7 Operating conditions 22 5.8 Mechanical construction 24 5.9 Operability . 25 5.10 P

21、ower supply . 26 5.11 Certificates and approvals . 26 5.12 Ordering information 26 5.13 Documentation 26 Annex A (normative) Classification of features as a function of measuring equipment . 27 Annex B (informative) Classification of features as a function of measurement principle . 29 Bibliography

22、49 Figure 1 Classification scheme for process measuring equipment . 16 Table A.1 Classification and documentation structure of measuring equipment. . 27 Table B.1 Classification and documentation structure of flow measuring equipment . 30 Table B.2 Classification and documentation structure of level

23、 measuring equipment 34 Table B.3 Classification and documentation structure of pressure measuring equipment . 38 Table B.4 Classification and documentation structure of temperature measuring equipment . 43 Table B.5 Classification and documentation structure of temperature measuring equipment . 46

24、61987-1 IEC:2006 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL DATA STRUCTURES AND ELEMENTS IN PROCESS EQUIPMENT CATALOGUES Part 1: Measuring equipment with analogue and digital output FOREWORD 1) The International Electrotechnical Commission (IEC) is a wor

25、ldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other

26、activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the sub

27、ject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions d

28、etermined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Co

29、mmittees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in wh

30、ich they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Public

31、ation and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure t

32、hat they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any n

33、ature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referen

34、ced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Internat

35、ional Standard IEC 61987-1 has been prepared by subcommittee 65B: Devices, of IEC technical committee 65: Industrial-process measurement and control. This standard cancels and replaces IEC/PAS 61987-1 published in 2002. This first edition constitutes a technical revision. This bilingual version (201

36、2-12) corresponds to the monolingual English version, published in 2006-12. 4 61987-1 IEC:2006 The text of this standard is based on the following documents: FDIS Report on voting 65B/599/FDIS 65B/602/RVD Full information on the voting for the approval of this standard can be found in the report on

37、voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result da

38、te indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61987-1 IEC:2006 5 INTRODUCTION In recent years, industry has become alert to the f

39、act that a great deal of time and effort is wasted in the transposition of measuring equipment data from one form to another. The technical data of an instrument, for example, may exist at the manufacturers facilty as two separate data sets for paper and electronic presentation: the end-user require

40、s much the same data for works standards, engineering data bases or commercial data bases. In most cases, however, the data cannot be automatically re-used because each application has its own particular data storage format. A second problem that belies the re-use of technical data is the content of

41、 the product descriptions themselves. There is little agreement between manufacturers on what information a technical data sheet should contain, how it should be arranged or how the results, for example, of particular performance tests should be presented. When transferring this information into a d

42、ata base, an end-user will always find gaps and proprietary interpretations that make the task more difficult. This standard aims at solving these problems by defining a generic structure and its content for industrial-process measuring and control equipment. It builds upon the assumption that, for

43、a given class of measuring equipment, for example, pressure measuring equipment, temperature measuring equipment or electromagnetic flow-measuring equipment, a set of non-proprietary structures and product features can be specified. The resulting documents cannot only be exchanged electronically, th

44、ey can also be presented to humans in an easily understandable form. This standard is applicable to electronic catalogues of process measuring equipment with analogue and digital output. Further parts with similar classification structures will be produced for measuring equipment with binary output

45、and interface equipment in the future. (The structure already contains a great many product features that are common to measuring equipment with binary output.) Similarly, Annex B has been prepared with a view to future standardization. This standard is not intended as a replacement for existing sta

46、ndards, but rather as a guiding document for all future standards which are concerned with the specifications of process measuring equipment. Every revision of an existing standard should take into account the structures and product features defined in Clause 5 of this standard or work towards a har

47、monization. Annex A contains a tabular overview of the classification and catalogue structure of process measuring equipment. Annex B contains tables with a further sub-classification for specific measured variables. Wherever possible, existing terms from international standards have been used to na

48、me the product features within the structures. In accordance with ISO 10241, Clause 3 of this standard contains a list of terms, definitions and sources. Documents created according to the standard are structured. A possible means of exchanging structured information free of layout information is gi

49、ven by Standard Generalized Mark-Up Language (SGML) described in ISO 8879 or Extensible Mark-Up Language (XML), which is derived from it. This standard could also provide the basis for arranging properties (data element types) that conform to IEC 61360 or ISO 13584. This would require that the features which, in this standard, can be textual units, graphical and tabular representations, etc., be broken down into properties (data el