IEC 61987-22-2015 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 22 Lists of Properties (LOPs).pdf

1、 IEC 61987-22 Edition 1.0 2015-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 22: Lists of Properties (LOPs) of valve body assemblies for electronic data exchange Mesure et commande dans les

2、processus industriels Structures de donnes et lments dans les catalogues dquipement de processus Partie 22: Listes de proprits (LOP) des ensembles de corps de vannes pour lchange lectronique de donnes IEC 61987-22:2015-09(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Swi

3、tzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the coun

4、try of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire

5、, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le

6、 copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.c

7、h Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications

8、is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standa

9、rds, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It al

10、so gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedi

11、a.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch

12、/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - websto

13、re.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internat

14、ionales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Cata

15、logue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publicatio

16、ns IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpubli

17、shed Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30

18、 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 60 000 entres terminologiques lectrotechniques, en anglais et en

19、franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si

20、vous avez des questions contactez-nous: csciec.ch. IEC 61987-22 Edition 1.0 2015-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 22: Lists of Properties (LOPs) of valve body assemblies for ele

21、ctronic data exchange Mesure et commande dans les processus industriels Structures de donnes et lments dans les catalogues dquipement de processus Partie 22: Listes de proprits (LOP) des ensembles de corps de vannes pour lchange lectronique de donnes INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISS

22、ION ELECTROTECHNIQUE INTERNATIONALE ICS 01.110; 25.040.40; 35.240.50 ISBN 978-2-8322-2890-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized dis

23、tributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61987-22:2015 IEC 2015 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions 6 4 General . 7 4.1 Overview. 7 4.2 Depiction of OLOP and DLOPs .

24、7 Annex A (normative) Operating List of Properties for valve body assembly and process pressure regulator . 8 Annex B (normative) Device Lists of Properties for different types of valve body assembly and process pressure regulator . 9 B.1 Device LOP for valve body assembly 9 B.2 Device LOP for globe

25、 valve . 9 B.3 Device LOP for diaphragm/pinch valve 9 B.4 Device LOP for gate valve 9 B.5 Device LOP for ball valve 10 B.6 Device LOP for butterfly valve . 10 B.7 Device LOP for eccentric plug valve 10 B.8 Device LOP for plug valve . 10 B.9 Device LOP for pressure reducing regulator and back pressur

26、e/excess pressure regulator . 10 Annex C (normative) Property library . 12 Annex D (normative) Block library for considered device types 13 Bibliography 14 IEC 61987-22:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL DATA STRUCTURES AND ELEMENTS

27、 IN PROCESS EQUIPMENT CATALOGUES Part 22: Lists of Properties (LOPs) of valve body assemblies for electronic data exchange FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National

28、 Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly

29、Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- government

30、al organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on tec

31、hnical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by

32、IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unif

33、ormity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)

34、 IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensu

35、re that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of a

36、ny nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the ref

37、erenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Inte

38、rnational Standard IEC 61987-22 has been prepared by subcommittee 65B: Measurement and control devices, of IEC technical committee 65: Industrial-process measurement, control and automation. The text of this standard is based on the following documents: FDIS Report on voting 65B/997/FDIS 65B/1018/RV

39、D Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 IEC 61987-22:2015 IEC 2015 A list of all parts in the IEC 61987 series, publish

40、ed under the general title Industrial-process measurement and control Data structures and elements in process equipment catalogues, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web

41、site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IEC 61987-22:2015 IEC 2015 5 INTRODUCTION The exchange of product data between companies, business systems, eng

42、ineering tools, data systems within companies and, in the future, control systems (electrical, measuring and control technology) can run smoothly only when both the information to be exchanged and the use of this information have been clearly defined. Prior to this standard, requirements on process

43、control devices and systems were specified by customers in various ways when suppliers or manufacturers were asked to quote for suitable equipment. The suppliers in their turn described the devices according to their own documentation schemes, often using different terms, structures and media (paper

44、, databases, CDs, e-catalogues, etc.). The situation was similar in the planning and development process, with device information frequently being duplicated in a number of different information technology (IT) systems. Any method that is capable of recording all existing information only once durin

45、g the planning and ordering process and making it available for further processing, gives all parties involved an opportunity to concentrate on the essentials. A precondition for this is the standardization of both the descriptions of the objects and the exchange of information. The IEC 61987 series

46、 proposes a method for standardization which will help both suppliers and users of process control equipment to optimize workflows both within their own companies and in their exchanges with other companies. Depending on their role in the process, engineering firms may be considered here to be eithe

47、r users or suppliers. The method specifies process control equipment by means of blocks of properties. These blocks are compiled into Lists of Properties (LOPs), each of which describes a specific equipment (device) type. The IEC 61987 series covers both properties that may be used in an inquiry or

48、a proposal and detailed properties required for integration of the equipment in computer systems for other tasks. IEC 61987-10 defines structure elements for constructing lists of properties for electrical and process control equipment in order to facilitate automatic data exchange between any two c

49、omputer systems in any possible workflow, for example engineering, maintenance or purchasing workflow and to allow both the customers and the suppliers of the equipment to optimize their processes and workflows. IEC 61987-10 also provides the data model for assembling the LOPs. IEC 61987-11, while specifying a generic structure for measuring equipment, provides several important detail descriptions, such as the handlin