IEC 62386-206-2009 Digital addressable lighting interface - Part 206 Particular requirements for contol gears - Conversion from digital signal into d.c voltage .pdf

1、 IEC 62386-206Edition 1.0 2009-06INTERNATIONAL STANDARD NORME INTERNATIONALEDigital addressable lighting interface Part 206: Particular requirements for control gear Conversion from digital signal into d. c. voltage (device type 5) Interface dclairage adressable numrique Partie 206: Exigences partic

2、ulires pour les appareillages de commande Conversion du signal numrique en tension continue (dispositifs de type 5) IEC62386-206:2009 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be re

3、produced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about ob

4、taining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que c

5、e soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publicat

6、ion, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organ

7、ization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendm

8、ent might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published:

9、www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing m

10、ore than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need furth

11、er assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour to

12、ut ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des

13、 publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Pu

14、blished CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de ter

15、mes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry

16、-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62386-206Edition 1.0 2009-06INTERNATIONAL STANDARD NORME INTERNATIONALEDigital

17、 addressable lighting interface Part 206: Particular requirements for control gear Conversion from digital signal into d. c. voltage (device type 5) Interface dclairage adressable numrique Partie 206: Exigences particulires pour les appareillages de commande Conversion du signal numrique en tension

18、continue (dispositifs de type 5) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE TICS 29.140.50; 29.140.99 PRICE CODECODE PRIXISBN 2-8318-1005-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique I

19、nternationale 2 62386-206 IEC:2009 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms and definitions .6 4 General description 6 5 Electrical specifications 6 6 Interface power supply .6 7 Transmission protocol structure6 8 Timing 7 9 Method of operation .7 10 Declaration

20、 of variables7 11 Definition of commands 8 12 Test procedures .13 Bibliography24 Figure 1 Application extended configuration command sequence example.9 Figure 2 Test sequence QUERY CONVERTER FEATURES.14 Figure 3 Test sequence OUTPUT RANGE .15 Figure 4 Test sequence INTERNAL PULL-UP 16 Figure 5 Test

21、sequence PHYSICAL MINIMUM .17 Figure 6 Test sequence DIMMING CURVE 18 Figure 7 Test sequence RESET CONVERTER SETTINGS.19 Figure 8 Test sequence QUERY OUTPUT LEVEL20 Figure 9 Test sequence QUERY FAILURE STATUS 21 Figure 10 Test sequence QUERY EXTENDED VERSION NUMBER.22 Figure 11 Test sequence RESERVE

22、D APPLICATION EXTENDED COMMANDS23 Table 1 Declaration of variables.8 Table 2 Summary of the application extended command set 13 62386-206 IEC:2009 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIGITAL ADDRESSABLE LIGHTING INTERFACE Part 206: Particular requirements for control gear Conversion from d

23、igital signal into d. c. voltage (device type 5) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operati

24、on on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “I

25、EC Publication(s)“). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this prepara

26、tion. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consens

27、us of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are

28、 made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications tra

29、nsparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot

30、be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and membe

31、rs of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or

32、 any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication ma

33、y be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62386-206 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. The text of this standard

34、 is based on the following documents: CDV Report on voting 34C/820/CDV 34C/841/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

35、4 62386-206 IEC:2009 This Part 206 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices). A list of all parts of the IEC 62386 series, under the general title: Digital addressable

36、 lighting interface, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the

37、 publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62386-206 IEC:2009 5 INTRODUCTION This first edition of IEC 62386-206 is published in conjunction with IEC 62386-101 and IEC 62386-102. The division of IEC 62386 into separately published parts provides for ease

38、of future amendments and revisions. Additional requirements will be added as and when a need for them is recognized. This International Standard, and the other parts that make up the IEC 62386-200 series, in referring to any of the clauses of IEC 62386-101 or IEC 62386-102, specify the extent to whi

39、ch such a clause is applicable and the order in which the tests are to be performed; The parts also include additional requirements, as necessary. All parts that make up the IEC 62386-200 series are self-contained and therefore do not include references to each other. Where the requirements of any o

40、f the clauses of IEC 62386-101 or IEC 62386-102 are referred to in this International Standard by the sentence “The requirements of IEC 62386-1XX, clause n apply”, this sentence is to be interpreted as meaning that all requirements of the clause in question of Part 101 or Part 102 apply, except any

41、which are inapplicable to the specific type of lamp control gear covered by Part 206. All numbers used in this International Standard are decimal numbers unless otherwise noted. Hexadecimal numbers are given in the format 0xVV, where VV is the value. Binary numbers are given in the format XXXXXXXXb

42、or in the format XXXX XXXX, where X is 0 or 1; “x“ in binary numbers means “dont care“. 6 62386-206 IEC:2009 DIGITAL ADDRESSABLE LIGHTING INTERFACE Part 206: Particular requirements for control gear Conversion from digital signal into d. c. voltage (device type 5) 1 Scope This International Standard

43、 specifies a protocol and test methods for the control by digital signals of electronic control gear, associated with the conversion from digital signal into d.c. voltage. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refe

44、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 62386-101:2009, Digital addressable lighting interface Part 101: General requirements System IEC 62386-102:2009, Digital addressable lighting interfac

45、e Part 102: General requirements Control gear 3 Terms and definitions For the purposes of this document, the terms and definitions given in Clause 3 of IEC 62386-101:2009 and Clause 3 of IEC 62386-102:2009 apply. 4 General description The requirements of Clause 4 of IEC 62386-101:2009 and Clause 4 o

46、f IEC 62386-102:2009 shall apply. 5 Electrical specifications The requirements of Clause 5 of IEC 62386-101:2009 and Clause 5 of IEC 62386-102:2009 shall apply. 6 Interface power supply The requirements of Clause 6 of IEC 62386-101:2009 and Clause 6 of IEC 62386-102:2009 shall apply if a power suppl

47、y is integrated with the control gear. 7 Transmission protocol structure The requirements of Clause 7 of IEC 62386-101:2009 and Clause 7 of IEC 62386-102:2009 shall apply. 62386-206 IEC:2009 7 8 Timing The requirements of Clause 8 of IEC 62386-101:2009 and Clause 8 of IEC 62386-102:2009 shall apply.

48、 9 Method of operation The requirements of Clause 9 of IEC 62386-101:2009 and Clause 9 of IEC 62386-102:2009 shall apply, with the following exception: Addition to Clause 9 of IEC 62386-102:2009: 9.9 Changing of physical min level Changing the physical minimum level shall force the minimum level and

49、 maximum level to be in a valid range. If operating with the logarithmic dimming curve, the PHYSICAL MIN LEVEL can be adjusted to allow the minimum arc power level of connected control gear to be matched to the logarithmic dimming curve of 9.1of IEC 62386-102:2009. A control gear with physical minimum arc power level of X %, requires the “PHYSICAL MIN LEVEL” to be set as f