IEC 62811-2015 AC and or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) - Performance requirements for low frequency squar.pdf

1、 IEC 62811 Edition 1.0 2015-04 INTERNATIONAL STANDARD NORME INTERNATIONALE AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) Performance requirements for low frequency square wave operation Appareillage lectronique aliment en courant alternatif et/ou cont

2、inu pour lampes dcharge ( lexclusion des lampes fluorescentes) Exigences de performance pour le fonctionnement en onde carre de basse frquence IEC 62811:2015-04(en-fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise

3、specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions

4、 about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tr

5、e reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir de

6、s droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The Inte

7、rnational Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Pleas

8、e make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Report

9、s and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and

10、withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of e

11、lectronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical ter

12、minology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedb

13、ack on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, ll

14、ectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Applicati

15、on autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avan

16、ce permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publicatio

17、ns IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en fran

18、ais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 60 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfini

19、tions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.

20、ch. IEC 62811 Edition 1.0 2015-04 INTERNATIONAL STANDARD NORME INTERNATIONALE AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) Performance requirements for low frequency square wave operation Appareillage lectronique aliment en courant alternatif et/ou c

21、ontinu pour lampes dcharge ( lexclusion des lampes fluorescentes) Exigences de performance pour le fonctionnement en onde carre de basse frquence INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 29.140.99 ISBN 978-2-8322-2600-1 Registered trademark of the Inte

22、rnational Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 I

23、EC 62811:2015 IEC 2015 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope 8 2 Normative references 8 3 Terms and definitions 8 4 General notes on tests 11 5 Marking . 11 6 General statement . 12 7 Starting conditions . 12 7.1 General . 12 7.2 Breakdown 12 7.3 Take-over . 13 7.4 Run-up 13 7.4.1 Run-up cu

24、rrent 13 7.4.2 Average peak current ratio (APCR) 13 7.4.3 D.C. current . 14 8 Operating conditions 14 8.1 General . 14 8.2 Power control 14 8.3 Frequency range of low frequency square wave 15 8.4 D.C. current 15 8.5 Average lamp potential against earth (for quartz arc bulbs only) . 15 8.6 Average pe

25、ak current ratio 15 8.7 Commutation time . 15 8.8 HF ripple . 16 8.9 Control interfaces . 16 8.10 Operating sustainability. 16 9 Displacement factor . 17 10 Supply current . 17 11 Endurance . 17 11.1 General . 17 11.2 Temperature cycling at 20 C and at +80 C . 17 11.3 Test at t c+10 K . 19 Annex A (

26、normative) Tests . 20 A.1 General requirements . 20 A.1.1 General . 20 A.1.2 Ambient temperature . 20 A.1.3 Supply voltage and frequency 20 A.1.4 Magnetic effects 20 A.1.5 Mounting and connection of reference lamps . 20 A.1.6 Reference lamp stability 20 A.1.7 Reference ballast. 21 A.1.8 Instrument c

27、haracteristics 21 Annex B (normative) Reference ballasts 22 IEC 62811:2015 IEC 2015 3 B.1 Marking . 22 B.2 Design characteristics . 22 B.2.1 Reference ballast for frequencies of 70 Hz to 400 Hz . 22 B.2.2 Protection 22 B.3 Operating characteristics for low frequency square wave 22 B.3.1 General . 22

28、 B.3.2 Impedance . 22 B.3.3 Series inductance and parallel capacitance . 23 B.4 Circuit for frequencies of low frequency square wave (see Figure 5) . 23 B.4.1 Power supply . 23 B.4.2 Instruments . 23 B.4.3 Wiring 23 Annex C (normative) Conditions for reference lamps . 24 Annex D (normative) Control

29、interface for controllable controlgear . 25 D.1 Overview. 25 D.2 Control by d.c. voltage 25 D.2.1 Circuit diagram Functional specification for d.c. voltage control (see Figure D.1) 25 D.2.2 Connection diagram . 25 D.2.3 Electrical specifications . 26 D.3 Control by pulse width modulation (PWM) . 27

30、D.3.1 Circuit diagram Functional specification for PWM control (see Figure D.4) . 27 D.3.2 Connection diagram . 28 D.3.3 Electrical specifications . 28 D.4 Control by DALI 28 Annex E (normative) Spectral analysis of power ripple: calculation procedure for amplitude spectrum ratio and guidance . 29 E

31、.1 General . 29 E.2 Mathematical background . 29 E.3 Description of the algorithm 29 E.4 Measurement procedure . 30 E.5 Test signal 30 E.5.1 General . 30 E.5.2 Description of the test signal 31 E.5.3 Outcome of the test signal . 31 Annex F (normative) Open circuit voltage method of measurement for p

32、ulse ignition . 32 Bibliography 33 Figure 1 Measurement of APCR during run-up and steady state 14 Figure 2 Test set-up for measuring the lamp potential against earth . 15 Figure 3 Commutation time, deviating waveform 16 Figure 4 Example of the cycling described under 11.2; Clause E.2. 18 Figure 5 Lo

33、w frequency square wave reference circuit . 19 Figure D.1 Schematic representation of the interface for 1 V to 10 V . 25 Figure D.2 Control device for multiple controlgear, for 1 V to 10 V . 26 Figure D.3 Control device is a current source. 26 Figure D.4 Schematic representation of the interface for

34、 PWM dimming. 27 4 IEC 62811:2015 IEC 2015 Figure D.5 Some typically PWM signals . 27 Figure D.6 Control device for multiple controlgear, for PWM 28 Table 1 Controlgear life time information 12 Table 2 Minimum OCV . 13 Table E.1 Settings for the analysis . 30 IEC 62811:2015 IEC 2015 5 INTERNATIONAL

35、ELECTROTECHNICAL COMMISSION _ AC AND/OR DC-SUPPLIED ELECTRONIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) PERFORMANCE REQUIREMENTS FOR LOW FREQUENCY SQUARE WAVE OPERATION FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardizatio

36、n comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Internationa

37、l Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in thi

38、s preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two

39、 organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the

40、 form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterp

41、retation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national o

42、r regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carrie

43、d out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Commi

44、ttees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to

45、 the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be h

46、eld responsible for identifying any or all such patent rights. International Standard IEC 62811 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. The text of this standard is based on the following documents: FDIS Report on voti

47、ng 34C/1132/FDIS 34C/1149/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 6 IEC 62811:2015 IEC 2015 The committee has decided t

48、hat the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMP

49、ORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. IEC 62811:2015 IEC 2015 7 INTRODUCTION This International Standard covers performance requirements for electronic controlgear for use on