IEC 62841-3-13-2017 Electric motor-operated hand-held tools transportable tools and lawn and garden machinery - Safety - Part 3-13 Particular requirements for t.pdf

1、 IEC 62841-3-13 Edition 1.0 2017-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 3-13: Particular requirements for transportable drills Outils lectroportatifs moteur, outils portables et machines po

2、ur jardins et pelouses Scurit Partie 3-13: Exigences particulires pour les perceuses transportables IEC 62841-3-13:2017-01(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reprod

3、uced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtain

4、ing additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce so

5、it et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utili

6、sez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the l

7、eading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corr

8、igenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, And

9、roid Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstor

10、e.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 ter

11、ms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Defi

12、nitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the C

13、ustomer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC

14、 Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur

15、les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres

16、 (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Dispon

17、ible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 16 langues additionnelles. Egalement a

18、ppel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary 65 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraite

19、s des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62841-3-13 Edition 1.0 2017-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Elect

20、ric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 3-13: Particular requirements for transportable drills Outils lectroportatifs moteur, outils portables et machines pour jardins et pelouses Scurit Partie 3-13: Exigences particulires pour les perceuses

21、transportables INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 25.120.40 ISBN 978-2-8322-3889-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obt

22、ained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 62841-3-13:2017 IEC 2017 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 General requirements 6 5 General

23、 conditions for the tests . 6 6 Radiation, toxicity and similar hazards . 6 7 Classification . 6 8 Marking and instructions 6 9 Protection against access to live parts . 7 10 Starting . 8 11 Input and current . 8 12 Heating 8 13 Resistance to heat and fire 8 14 Moisture resistance . 8 15 Resistance

24、to rusting . 8 16 Overload protection of transformers and associated circuits 8 17 Endurance . 8 18 Abnormal operation . 8 19 Mechanical hazards . 9 20 Mechanical strength 10 21 Construction 11 22 Internal wiring 12 23 Components 12 24 Supply connection and external flexible cords . 12 25 Terminals

25、for external conductors 12 26 Provision for earthing 12 27 Screws and connections 12 28 Creepage distances, clearances and distances through insulation . 12 Annexes . 15 Annex I (informative) Measurement of noise and vibration emissions . 15 Annex K (normative) Battery tools and battery packs . 16 B

26、ibliography 17 Figure 101 Examples of drill designs 13 Figure 102 Test probe 14 Figure 103 Check of a guard for the drill chuck (plan view from top) 14 Table 4 Required performance levels . 9 Table K.4 Required performance levels 16 IEC 62841-3-13:2017 IEC 2017 3 INTERNATIONAL ELECTROTECHNICAL COMMI

27、SSION _ ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 3-13: Particular requirements for transportable drills FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nationa

28、l electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical S

29、pecifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Inte

30、rnational, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The f

31、ormal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations

32、 for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user

33、. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication s

34、hall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent cer

35、tification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal i

36、njury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative reference

37、s cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for iden

38、tifying any or all such patent rights. International Standard IEC 62841-3-13 has been prepared by IEC technical committee 116: Safety of motor-operated electric tools. The text of this standard is based on the following documents: FDIS Report on voting 116/309/FDIS 116/315/RVD Full information on th

39、e voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This Part 3-13 is to be used in conjunction with the first edition of IEC 62841-1 (2014). 4 IEC 62841-3-1

40、3:2017 IEC 2017 This Part 3-13 supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable drills. Where a particular subclause of Part 1 is not mentioned in this Part 3-13, that subclause applies as far as re

41、levant. Where this standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. The following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. The terms defined in Clause 3 ar

42、e printed in bold typeface. Subclauses, notes and figures which are additional to those in Part 1 are numbered starting from 101. A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety, c

43、an be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed

44、, withdrawn, replaced by a revised edition, or amended. NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in

45、 accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. IEC 62841-3-13:2017 IEC

46、2017 5 ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 3-13: Particular requirements for transportable drills 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to transportable drills, with

47、manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. NOTE 101 Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This

48、 part of IEC 62841 does not apply to magnetic drill stands and drill motors. NOTE 102 Magnetic drill stands and drill motors will be covered by a future part of IEC 62841-3. NOTE 103 In Europe (EN 62841-3-13), the following conditions apply: Radial arm drills and stationary drilling machines are cov

49、ered by EN 12717. 2 Normative references This clause of Part 1 is applicable. 3 Terms and definitions This clause of Part 1 is applicable, except as follows: 3.2 accessory Addition: Note 1 to entry: Typical accessories for drills are bits for drilling and deburring. 3.101 drill tool equipped with a typical three jaw chuck specifically designed to bore holes in various materials such as metal, plastics, wood,