IEC 62846-2016 Railway applications - Current collection systems - Requirements for and validation of measurements of the dynamic interaction between pantograph.pdf

1、 IEC 62846 Edition 1.0 2016-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Current collection systems Requirements for and validation of measurements of the dynamic interaction between pantograph and overhead contact line Applications ferroviaires Systmes de captage de courant E

2、xigences et validation des mesures de linteraction dynamique entre le pantographe et la catnaire IEC 62846:2016-10(en-fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2016 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be

3、reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about

4、obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que

5、 ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication,

6、 utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is

7、 the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition,

8、a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac O

9、S, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - w

10、ebstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 0

11、00 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms an

12、d Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact

13、 the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publicatio

14、ns IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographique

15、s sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents c

16、ritres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues.

17、Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egale

18、ment appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary 65 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures ex

19、traites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62846 Edition 1.0 2016-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Rail

20、way applications Current collection systems Requirements for and validation of measurements of the dynamic interaction between pantograph and overhead contact line Applications ferroviaires Systmes de captage de courant Exigences et validation des mesures de linteraction dynamique entre le pantograp

21、he et la catnaire INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 45.060 ISBN 978-2-8322-3651-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obt

22、ained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 IEC 62846:2016 IEC 2016 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references. 6 3 Terms and definitions 6 4 Symbols and abbreviate

23、d terms . 9 5 General . 10 6 Measurement of total mean uplift force . 11 7 Measurement of contact force 13 7.1 General requirements 13 7.2 Aerodynamic influence of the measurement system . 14 7.3 Inertia correction . 14 7.4 Aerodynamic correction . 14 7.5 Calibration of the measurement system . 15 7

24、.6 Measurement parameters 16 7.7 Measurement results . 16 8 Measurement of displacement 16 8.1 General . 16 8.2 Vertical displacement of the contact point 16 8.3 Uplift at the support . 16 8.4 Measurement of other displacements in the overhead contact line 16 9 Measurement of arcing 17 9.1 General r

25、equirements 17 9.2 Calibration of the arc measurement system 18 9.3 Adjustment of threshold for the measurement distance . 18 9.4 Values to be measured 18 9.5 Measurement results . 19 Annex A (informative) Particular conditions existing in certain countries (exceptions) Japan . 20 A.1 Measurement of

26、 percentage of all arcing AQ 20 A.1.1 General requirements . 20 A.1.2 Calibration of the arc measurement system . 20 A.1.3 Adjustment of threshold for the measurement distance 21 A.1.4 Values to be measured . 21 A.1.5 Measurement results 21 A.2 Measurement of percentage of current loss . 22 A.2.1 Ge

27、neral requirements . 22 A.2.2 Current loss detection . 22 A.2.3 Measurement result 22 Annex B (informative) Contact wire bending stress . 24 B.1 General . 24 B.2 Measurement points of contact wire bending stress 24 B.3 Measurement result . 24 Bibliography . 25 Figure 1 Principle arrangements for a t

28、ethered test . 12 IEC 62846:2016 IEC 2016 3 Figure 2 Contact force measurement 13 Figure 3 Example for segmented contact strip 14 Figure 4 Detector location 18 Figure A.1 Test setup 22 Table 1 Initial test speed 12 4 IEC 62846:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RAILWAY APPLICA

29、TIONS CURRENT COLLECTION SYSTEMS REQUIREMENTS FOR AND VALIDATION OF MEASUREMENTS OF THE DYNAMIC INTERACTION BETWEEN PANTOGRAPH AND OVERHEAD CONTACT LINE FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotech

30、nical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications

31、, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, go

32、vernmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisio

33、ns or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for internat

34、ional use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order

35、 to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clear

36、ly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bo

37、dies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, proper

38、ty damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in th

39、is publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any o

40、r all such patent rights. International Standard IEC 62846 has been prepared by IEC technical committee 9: Electrical equipment and systems for railways. This standard has been derived from EN 50317. The text of this standard is based on the following documents: FDIS Report on voting 9/2198/FDIS 9/2

41、205/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. IEC 62846:2016 IEC 2016 5 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The readers attention is drawn to the fact that A

42、nnex A lists all of the “in-some-country” clauses on differing practices of a permanent nature relating to the subject of this standard. The following differing practices of a less permanent nature exist in the countries indicated below. Subclause 3.20: t totalis the total measuring time (China). Su

43、bclause 9.5: The evaluation of the interaction includes counting the number of arcs longer than a predefined length (China). The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in t

44、he data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the co

45、rrect understanding of its contents. Users should therefore print this document using a colour printer. 6 IEC 62846:2016 IEC 2016 RAILWAY APPLICATIONS CURRENT COLLECTION SYSTEMS REQUIREMENTS FOR AND VALIDATION OF MEASUREMENTS OF THE DYNAMIC INTERACTION BETWEEN PANTOGRAPH AND OVERHEAD CONTACT LINE 1

46、Scope This International Standard specifies the functional requirements for output and accuracy of measurements of the dynamic interaction between pantograph and overhead contact line. 2 Normative references The following documents are referred to in the text in such a way that some or all of their

47、content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 62486:2010, Railway applications Current collection systems Technical criteria for th

48、e interaction between pantograph and overhead line (to achieve free access) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: ava

49、ilable at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 3.1 collector head pantograph head part of the pantograph supported by the frame which includes contact strips, horns and may include a suspension SOURCE: IEC 60494-1:2013, 3.2.3, modified the term “pantograph head“ has been added. 3.2 contact point point of mechanical contact between a co