API MPMS 12 1 2-2018 Manual of Petroleum Standards Chapter 12-Calculation of Petroleum Quantities Section 1-Calculation of Static Petroleum Quantities Part 2-Ca.pdf

1、Manual of Petroleum StandardsChapter 12Calculation of Petroleum QuantitiesSection 1Calculation of Static Petroleum QuantitiesPart 2Calculation Procedures for Tank CarsSECOND EDITION, FEBRUARY 2018Special NotesAPI publications necessarily address problems of a general nature. With respect to particul

2、ar circumstances, local, state, and federal laws and regulations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or useful

3、ness of the information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors, consultants, or other assignees represent that use of this

4、publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to ensure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarante

5、e in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.API publications are published to facilitate the broad a

6、vailability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any

7、 way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarant

8、ee that such products do in fact conform to the applicable API standard.All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission

9、from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2018 American Petroleum InstituteForewordNothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or

10、 use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent.The verbal forms used to express the provisions in this document are as follows.Shall: As use

11、d in a standard, “shall” denotes a minimum requirement in order to conform to the standard.Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the standard.May: As used in a standard, “may” denotes a course of action permi

12、ssible within the limits of a standard.Can: As used in a standard, “can” denotes a statement of possibility or capability.This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API st

13、andard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street, NW, Washington, D

14、C 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to two years may be a

15、dded to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005.Suggested revisions are invited and should be submitt

16、ed to the Standards Department, API, 1220 L Street, NW, Washington, DC 20005, standardsapi.org.iiiContentsPage1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Normative Refer

17、ences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Terms, Definitions, Acronyms, and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 General . .

18、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 Acronyms and Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19、 . . . . . . . 64 Required Data Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20、 . . . . . . . . . . . . . . . . . . . . . . . . 74.2 Tank Car Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.3 Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Actual Loaded Quantity Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115.1 General . . . . . . . . . . . . . . . . . . . . . . . .

22、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115.2 General Purpose Cars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115.3 Pressure Cars . . .

23、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115.4 Vapor Space Heel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24、. . . . 125.5 Overload check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Rounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25、. . . . . . . . . . . . . . . . . . . . . . 126.1 Data Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126.2 Rounding of Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Annex A (normative) Loading Target Quantity Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Annex B (informative) Calculation of Tank Car Shell Expansion/Contraction with Te

27、mperature . . . . . . . . . . 19Annex C (informative) Calculation of Tank Car Shell Expansion with Pressure . . . . . . . . . . . . . . . . . . . . . . . . 21Annex D (informative) Calculation of Magnetic Gauge Offsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Anne

28、x E (informative) Tank Car Reconciliation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Annex F (informative) Calculation Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Bib

29、liography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53FiguresD.1 Magnetic Float Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30、. . . . . . . . . . . . . . . . . 22D.2 Derivation of a Spherical Volume Segment or Bowl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26E.1 Butene Static ScaleBOL Difference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31、 . . . . . . 28E.2 Actual Tare Minus Stenciled Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Tables1 Significant Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32、 . . . . . . . . . . . . . 13B.1 Shell Temperature (F) Tank Car Volume Correction Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20C.1 Pressure (psig) Expansion Table for a Typical (D = 120 in., t = 11/16-in. mild steel) Pressure Car . . . 21D.1 Temperature Offset for a Re

33、ference Relative Density of 0.50000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26D.2 Temperature Offset for a Reference Relative Density of 1.0000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26F.1 Outage Liquid Capacity TableLoading Target CalculationVolume Limitation

34、. . . . . . . . . . . . . . . . 30F.2 Outage Liquid Capacity TableActual Loaded Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31F.3 Outage Liquid Capacity TableLoading Target CalculationWeight Limitation . . . . . . . . . . . . . . . . 33F.4 Outage Liquid Capacity T

35、able with Nozzle Height IncludedLoading Target CalculationVolume Limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34vContentsPageF.5 Example 5: Outage Liquid Capacity Table with Nozzle Height IncludedActual

36、 Loaded Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36F.6 Outage Vapor Capacity TableLoading Target CalculationVolume Limitation . . . . . . . . . . . . . . . . 37F.7 Outage Vapor Capa

37、city TableLoading Target CalculationUnderstated Loading Temperature . . 38F.8 Outage Vapor Capacity TableActual Loaded Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39F.9 Outage Vapor Capacity TableActual Loaded CalculationOverstated Target Loading Temperature Resul

38、ts in Overloading by Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41F.10 Outage Vapor Capacity TablePressure Car Target Loading CalculationSummer Loading . . . . . 42F.11 Outage Vapor Capacity TablePressure Car Target Loading Calc

39、ulationWinter Loading . . . . . . . 43F.12 Outage Vapor Capacity TablePressure Car Target Loading CalculationSummer Loading . . . . . 45F.13 Innage Liquid Capacity TableLoading Target CalculationVolume Limitation . . . . . . . . . . . . . . . . 46F.14 Tank Car Capacity Table . . . . . . . . . . . .

40、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48F.15 Tank Car Capacity Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49F.16 Tank Car Capacity Table . . . . .

41、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50F.17 Tank Car Capacity Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51F.18 Tank Car Capacity Ta

42、ble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52viIntroductionThis chapter of the Manual of Petroleum Measurement Standards describes the standardized method for calculating target loading quantities and actual loade

43、d quantities of liquids in tank cars. Also addressed within this chapter is an explanation of the factors required for the calculations.vi1Chapter 12Calculation of Petroleum QuantitiesSection 1Calculation of Static Petroleum QuantitiesPart 2Calculation Procedures for Tank Cars1 Scope This chapter is

44、 applicable to all crude oils, petroleum products, and petrochemicals (including LPGs and other liquefied gases) transported by rail tank car. It does not cover any products loaded or measured as solids. It defines the terms required to understand the calculations and provides instructions for their

45、 use. The cars are assumed to be on level ground.2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only edition cited applies. For undated references, the latest edition of the referenced document applies (includin

46、g any addenda or errata, or both).API Manual of Petroleum Measurement Standards (MPMS) Chapter 1, VocabularyAPI Manual of Petroleum Measurement Standards (MPMS) Chapter 3.2, Tank Car MeasurementAPI Manual of Petroleum Measurement Standards (MPMS) Chapter 10, Sediment and WaterAPI Manual of Petroleum

47、 Measurement Standards (MPMS) Chapter 11.2.4, Temperature Correction for the Volume of NGL and LPG, Tables 23E, 24E, 53E, 54E, 59E, and 60EAPI Manual of Petroleum Measurement Standards (MPMS) Chapter 11.2.5, A Simplified Vapor Pressure Correlation for Commercial NGLsAPI Manual of Petroleum Measureme

48、nt Standards (MPMS) Chapter 12.2, Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction FactorsASTM D1555, Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane3 Terms, Definitions, Acronyms, and Abbrev

49、iationsFor the purposes of this document, the following terms and definitions apply. Terms of more general use (i.e. API Gravity, Density, etc.) may be found in API MPMS Chapter 1.3.1 General3.1.1 capacity table adjustment factor CTAFCorrection applied to capacity table volumes. 3.1.2 closed loading or closed unloadingThe manway remains closed or covered during loading or unloading. 2API MPMS CHAPTER 12.1.2CALCULATION OF PETROLEUM QUANTITIES3.1.3 compartment carA car with two or more independent (no common walls) tanks, each with its own manway, referenc