API MPMS 12 2 3 ADD 1-2007 Manual of Petroleum Measurement Standards Chapter 12 Calculation of Petroleum Quantities (First Edition)《石油测量标准手册 第12章 石油量值的计算 第1版》.pdf

1、Manual of PetroleumMeasurement StandardsChapter 12Calculation of Petroleum QuantitiesAddendum 1August 2007SPECIAL NOTESAPI publications necessarily address problems of a general nature. With respect to particularcircumstances, local, state, and federal laws and regulations should be reviewed.Neither

2、 API nor any of APIs employees, subcontractors, consultants, committees, or otherassignees make any warranty or representation, either express or implied, with respect to theaccuracy, completeness, or usefulness of the information contained herein, or assume anyliability or responsibility for any us

3、e, or the results of such use, of any information or processdisclosed in this publication. Neither API nor any of APIs employees, subcontractors, con-sultants, or other assignees represent that use of this publication would not infringe upon pri-vately owned rights.API publications may be used by an

4、yone desiring to do so. Every effort has been made bythe Institute to assure the accuracy and reliability of the data contained in them; however, theInstitute makes no representation, warranty, or guarantee in connection with this publicationand hereby expressly disclaims any liability or responsibi

5、lity for loss or damage resultingfrom its use or for the violation of any authorities having jurisdiction with which this publi-cation may conflict.API publications are published to facilitate the broad availability of proven, sound engineer-ing and operating practices. These publications are not in

6、tended to obviate the need forapplying sound engineering judgment regarding when and where these publications shouldbe utilized. The formulation and publication of API publications is not intended in any wayto inhibit anyone from using any other practices.Any manufacturer marking equipment or materi

7、als in conformance with the markingrequirements of an API standard is solely responsible for complying with all the applicablerequirements of that standard. API does not represent, warrant, or guarantee that such prod-ucts do in fact conform to the applicable API standard.All rights reserved. No par

8、t of this work may be reproduced, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, N.W., Washington, D.C. 20005

9、.Copyright 2007 American Petroleum InstituteFOREWORDNothing contained in any API publication is to be construed as granting any right, by impli-cation or otherwise, for the manufacture, sale, or use of any method, apparatus, or productcovered by letters patent. Neither should anything contained in t

10、he publication be construedas insuring anyone against liability for infringement of letters patent.This document was produced under API standardization procedures that ensure appropriatenotification and participation in the developmental process and is designated as an API Stan-dard. Questions conce

11、rning the interpretation of the content of this publication or commentsand questions concerning the procedures under which this publication was developed shouldbe directed in writing to the Director of Standards, American Petroleum Institute, 1220 LStreet, N.W., Washington, D.C. 20005. Requests for

12、permission to reproduce or translate allor any part of the material published herein should also be addressed to the director.Generally, API Standards are reviewed and revised, reaffirmed, or withdrawn at least everyfive years. A one-time extension of up to two years may be added to this review cycl

13、e. Statusof the publication can be ascertained from the API Standards Department, telephone (202)682-8000. A catalog of API publications and materials is published annually and updatedquarterly by API, 1220 L Street, N.W., Washington, D.C. 20005.Suggested revisions are invited and should be submitte

14、d to the Standards and PublicationsDepartment, API, 1220 L Street, NW, Washington, D.C. 20005, standardsapi.org.Addendum 1 to API MPMS Chapter 12Calculation of Petroleum Quantities1Guidance to Industry on the Application of API MPMS Chapter 11IntroductionAfter considerable time and effort, a revisio

15、n of API MPMS Ch. 11.1 (Physical PropertiesDataTemperature and Pressure Correction Factors for Generalized Crude Oils, RefinedProducts, and Lubricating Oils) was published as an AdobePDF file on CD with anaccompanying executable program (for calculating and printing) in September 2004. Laterthat yea

16、r, a CD with a MicrosoftExcel Add-In was released, as was another CD with ANSIC-code subroutines. As users have started to implement the 2004 version of API MPMSCh. 11.1, a number of concerns and questions have arisen on how the API MPMS Ch. 11.1(2004) harmonizes with existing MPMS Standards, partic

17、ularly API MPMS Ch. 12.MPMS Chapter InterrelationshipsCurrently, the Manual of Petroleum Measurement Standards is organized into Chapters cov-ering general measurement areas and several of these Standards are interrelated. Forinstance, numerous Standards reference API MPMS Ch. 11.1. There is at pres

18、ent consider-able uncertainty amongst users as to which takes precedence when Standards do not concuron a specific subject, in particular Chapters 11 and 12. When these differences occur the fol-lowing criteria should be applied.API MPMS Ch. 11.1 is the primary standard for the determination of the

19、temperature(CTL), pressure (CPL), and combined temperature and pressure (CTPL) correction factorsfor crude oil, refined products, and lubricating oils, either by presentation of specific imple-mentation procedures or by reference to other publications. API MPMS Ch. 12 is the primary standard for the

20、 calculation of volume quantities. It deter-mines the discrimination levels (rounding) required for each input variable and correctionfactor in a specific volume calculation procedure, and the sequence and manner in which toapply the appropriate parameters (RHOb, APIb, RDb, CTL, Fp, CPL, and CTPL).N

21、ote: While the determination of a combination pressure and temperature factor, CTPL, is specified inAPI MPMS Ch. 11.1, its application is not currently addressed in API MPMS Ch. 12 but will beupon the next revision. 8/07#FFKVKQPCNEQRKGUCTGCXCKNCDNGVJTQWIJ+*52JQPG1TFGTU 6QNNHTGGKPVJG75CPF%CPCFC .QECNCPF+PVGTPCVKQPCN (CZ1TFGTU 1PNKPG1TFGTU INQDCNKJUEQO+PHQTOCVKQPCDQWV#2+2WDNKECVKQPU2TQITCOUCPF5GTXKEGUKUCXCKNCDNGQPVJGYGDCVYYYCRKQTI.5VTGGV099CUJKPIVQP&%75#