API MPMS 8 4-2014 Manual of Petroleum Measurement Standards Chapter 8 4 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement (THIRD E.pdf

1、Manual of Petroleum Measurement Standards Chapter 8.4 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement THIRD EDITION, MARCH 2014Special Notes API publications necessarily address problems of a general nature. With respect to particular circumstances, local, state, and

2、federal laws and regulations should be reviewed. Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information contained h

3、erein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon

4、 privately owned rights. API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarantee in connection with this publicat

5、ion and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict. API publications are published to facilitate the broad availability of proven, sound engi

6、neering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any way to inhibit anyone from using

7、 any other practices. Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact

8、 conform to the applicable API standard. Classified areas may vary depending on the location, conditions, equipment, and substances involved in any given situation. Users of this standard should consult with the appropriate authorities having jurisdiction. Users of this standard should not rely excl

9、usively on the information contained in this document. Sound business, scientific, engineering, and safety judgment should be used in employing the information contained herein. Where applicable, authorities having jurisdiction should be consulted. Work sites and equipment operations may differ. Use

10、rs are solely responsible for assessing their specific equipment and premises in determining the appropriateness of applying the instructions. At all times users should employ sound business, scientific, engineering, and judgment safety when using this standard. API is not undertaking to meet the du

11、ties of employers, manufacturers, or suppliers to warn and properly train and equip their employees, and others exposed, concerning health and safety risks and precautions, nor undertaking their obligations to comply with authorities having jurisdiction. All rights reserved. No part of this work may

12、 be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005. Copyrigh

13、t 2014 American Petroleum InstituteForeword Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the publi

14、cation be construed as insuring anyone against liability for infringement of letters patent. Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification. Should: As used in a standard, “should” denotes a recommendation or that which is advised but not

15、 required in order to conform to the specification. This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API standard. Questions concerning the interpretation of the content of this

16、 publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any

17、part of the material published herein should also be addressed to the director. Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to two years may be added to this review cycle. Status of the publication can be ascertain

18、ed from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005. Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW, Washington,

19、DC 20005, standardsapi.org. iiiContents Page 1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Referenced Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 Summary of Practice. . . . . . . . . . . . . . . .

21、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 Significance and Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 General Comments . . . .

22、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 Specific Sampling Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 Speci

23、al Precautions and Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 9 Keywords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24、 . . . . . . . 6 Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figures 1 Nozzle Extension for Nozzle Sampling with 4 oz Bottle . . . . . . . . . . . . . . . . . . . . . . . . . .

25、. . . . . . . . . . . . . . . 3 2 Slotted Stand Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Assembly for Bottle Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26、. . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Tank Sampling Depths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 Assemblies for Tap Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6 Cooling Bath for Reid Equivalent Vapor Pressure Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7 Probes for Line Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 8 Spacer for Nozzle Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 9 Extension for Nozzle Sampling . . . . . . . . . . . . . . . . . . . . .

29、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 10 Assembly for Nozzle Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tables 1 Summary of Gasoline Sampling Procedures and Applicabi

30、lity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 vDesignation: D5842 14 Manual of Petroleum Measurement Standards (MPMS) Chapter 8.4 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement 1 This standard is issued under the xed designation D5842; t

31、he number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.

32、 1. Scope* 1.1 This practice covers procedures and equipment for obtaining, mixing, and handling representative samples of volatile fuels for the purpose of testing for compliance with the standards set forth for volatility related measurements appli- cable to light fuels. The applicable dry vapor p

33、ressure equiva- lent range of this practice is 13 to 105 kPa (2 to 16 psia). 1.2 This practice is applicable to the sampling, mixing, and handling of reformulated fuels including those containing oxygenates. 1.3 The values stated in SI units are to be regarded as the standard except in some cases wh

34、ere drawings may show inch-pound measurements which are customary for that equip- ment. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro- priate safety and health practi

35、ces and determine the applica- bility of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: 2 D4057 Practice for Manual Sampling of Petroleum and Petroleum Products (API MPMS Chapter 8.1) D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products (API MPM

36、S Chapter 8.2) D5854 Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products (API MPMS Chap- ter 8.3) D7717 Practice for Preparing Volumetric Blends of Dena- tured Fuel Ethanol and Gasoline Blendstocks for Labora- tory Analysis 2.2 API Standards: 3 MPMS Chapter 8.1Prac

37、tice for Manual Sampling of Pe- troleum and Petroleum Products (ASTM Practice D4057) MPMS Chapter 8.2Practice for Automatic Sampling of Petroleum and Petroleum Products (ASTM Practice D4177) MPMS Chapter 8.3Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products (ASTM

38、Practice D5854) 3. Terminology 3.1 Denitions of Terms Specic to This Standard: 3.1.1 bottom sample, na sample obtained from the mate- rial at the bottom of the tank, container, or line at its lowest point. 3.1.1.1 DiscussionIn practice the term bottom sample has a variety of meanings. As a result, i

39、t is recommended that the exact sampling location (for example, 15 cm 6 in. from the bottom) should be specied when using this term. 3.1.2 dead legs, nsections of pipe that, by design, do not allow for the ow of material through them. 3.1.2.1 DiscussionDead legs are not suitable for obtaining repres

40、entative samples. 3.1.3 relief lines, nsections of pipe that lead to a pressure/ vacuum relief valve. 3.1.3.1 DiscussionRelief lines are not suitable for obtain- ing representative samples. 3.1.4 stand pipes, nvertical sections of pipe or tubing extending from the gaging platform to near the bottom

41、of tanks that are equipped with external or internal oating roofs. Stand pipes also may be found on ships and barges. 3.1.4.1 DiscussionStand pipes which are not slotted or perforated will not yield representative samples. Further infor- mation on proper stand pipe design is given in 6.4.3. 1 This p

42、ractice is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and the API Committee on Petroleum Measurement, and is the direct responsibility of Subcommittee D02.02 /COMQ on Hydrocarbon Measurement for Custody Transfer (Joint ASTM-API). This practice ha

43、s been approved by the sponsoring committees and accepted by the Cooperating Societies in accordance with established procedures. This practice was issued as a joint ASTM-API standard in 1995. Current edition approved Jan. 15, 2014. Published January 2014. Originally approved in 1995. Last previous

44、edition approved in 2009 as D584204 (2009). DOI: 10.1520/D5842-14. 2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standards volume information, refer to the standards Document Summary page on the AST

45、M website. 3 Available from American Petroleum Institute (API), 1220 L. St., NW, Washington, DC 20005-4070, http:/www.api.org. *A Summary of Changes section appears at the end of this standard Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United

46、States 13.1.5 Other sample denitions are given in Practice D4057/ API MPMS Chapter 8.1. 4. Summary of Practice 4.1 It is necessary that the samples be representative of the fuel in question. The basic principle of each sampling proce- dure involves obtaining a sample in such a manner and from such l

47、ocations in the tank or other container that the sample will be representative of the fuel. A summary of the sampling procedures and their application is presented in Table 1. Each procedure is suitable for sampling a material under denite storage, transportation, or container conditions. The precau

48、- tions required to ensure the representative character of the samples are numerous and depend upon the tank, carrier, container, or line from which the sample is being obtained, the type and cleanliness of the sample container, and the sampling procedure that is to be used. 5. Signicance and Use 5.

49、1 The dry vapor pressure equivalent (DVPE) of volatile motor fuels is regulated by federal and state air pollution control agencies. In order to meet the letter of these regulations, it is necessary to sample, handle, and test these products in the precise manner as prescribed in this practice. 6. General Comments 6.1 Sample Containers: 6.1.1 Sample containers are clear or brown glass bottles, uorinated high-density polyethylene bottles, or metal cans. The clear glass bottle is advantageous because it is easily examined visually for cleanliness, and also ma