ASTM C933-2018 Standard Specification for Welded Wire Lath.pdf

1、Designation: C933 18Standard Specification forWelded Wire Lath1This standard is issued under the fixed designation C933; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates t

2、he year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers welded wire lath, flat orself-furring, with or without backing, designed for use as a baseto receive portland cement-based interior plaster a

3、nd exteriorstucco.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with i

4、nternationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A

5、641/A641M Specification for ZincCoated (Galvanized)Carbon Steel WireC11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsE2556/E2556M Specification for Vapor Permeable FlexibleSheet Water-Resistive Barriers Intended for MechanicalAttachment2.2 Federal Specifications:UU-B-790 B

6、uilding Paper, Vegetable Fiber: (Kraft,Waterproofed, Water Repellent and Fire Resistant)33. Terminology3.1 Definitions of terms used in this standard shall be inaccordance with Terminology C11.4. Materials and Manufacture4.1 Welded wire lath shall be fabricated from not less than0.0625 in. (1.588 mm

7、), cold-drawn, galvanized steel wire,conforming to Specification A641/A641M.4.1.1 Diameter tolerance for galvanized wire shall be inaccordance with Specification A641/A641M.4.1.2 The wire shall be zinc-coated (galvanized) in accor-dance with Specification A641/A641M.4.1.3 The factory-attached water-

8、resistive barrier shall con-form to Federal Specification UU-B-790 or ASTM Specifica-tion E2556/E2556M. The water-resistive barrier shall be eitherabsorptive or water resistant. The water-resistive barrier shallhave a bursting strength of not less than that required tomaintain integrity under normal

9、 hand- or machine-applicationpressures.4.1.4 The factory-attached water-resistive barrier shall beattached to the lath to prevent accidental removal duringshipping, handling or installation. Attachment of the water-resistive barrier shall allow lapping of wire-to-wire and water-resistive barrier to

10、water-resistive barrier of not less than onemesh at ends and edges and shall permit full embedment, in notless than14 in. (6 mm) of plaster, of not less than one-half ofthe total length and width of the wire.4.1.5 The thickness of the embedment of the lath and plastershall be measured from the back

11、plane of the back wire,exclusive of furring, to the water-resistive barrier or surface ofthe substrate.5. Dimensions and Permissible Variations5.1 Openings and Stiffening:5.1.1 Lath shall be welded at all intersections of wire toform openings not more than 2 by 2 in. (51 by 51 mm).5.1.2 Reinforced l

12、ath shall be permitted to be reinforcedcontinuously and parallel to the long dimension of the lath atintervals of not more than 6 in. (150 mm). Wires used for thispurpose shall range from 0.072 to 0.1205 in. (1.9 to 3.1 mm).Reduction of the size of the openings to less than 2 by 2 in. (51by 51 mm) s

13、hall also be permitted.5.1.3 Self-furring crimps on self-furring lath shall projectnot less than14 in. (6 mm) from the plane of the back of thelath.5.2 ThicknessThe nominal thickness shall be18 in.(3.2 mm), exclusive of self-furring crimps, with a permissiblevariation of 6132 in. (0.8 mm).1This spec

14、ification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilityof Subcommittee C11.02 on Specifications and Test Methods for Accessories andRelated Products.Current edition approved Oct. 1, 2018. Published October 2018. O

15、riginallyapproved in 1980. Last previous edition approved in 2014 as C933 14. DOI:10.1520/C0933-18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Doc

16、ument Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700,

17、West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World

18、 Trade Organization Technical Barriers to Trade (TBT) Committee.15.3 WidthThe nominal width shall be 28 to 54 in. (700 to1370 mm), with a permissible variation of 634 in. (19 mm).5.4 LengthThe minimum length shall be 48 in. (1200 mm)for sheets or a maximum of 150 ft (45.720 m) for rolls with apermis

19、sible variation of 634 in. (19 mm) for sheets or rolls.5.5 WeightThe weight, exclusive of factory-attachedwater-resistive barrier, shall be a minimum of 1.14 lb/yd2(0.618 kg/m2). The weight of reinforced lath, exclusive ofwater-resistive barrier, shall be a minimum of 1.95 lb yd2(1.058 kg/m2).6. Sam

20、pling6.1 When specified by the purchase agreement, samples ofwelded wire lath shall be taken at the place of manufacture orat the place of destination. If samples are taken at thedestination, such samples shall be taken within 24 h of thereceipt of the material.6.2 At least 0.25 % of the number of s

21、heets of welded wirelath in a shipment, but not less than three sheets, shall be soselected as to be representative of the shipment and shallconstitute a sample for the purpose of tests by the purchaser oruser.7. Inspection7.1 Inspection of the welded wire lath shall be agreed uponbetween the purcha

22、ser and the producer or supplier as part ofthe purchase agreement.8. Rejection8.1 Rejection of welded wire lath that fails to conform to therequirements of the specification shall be reported to theproducer or supplier promptly and in writing. The notice ofrejection shall contain a statement documen

23、ting how thewelded wire lath has failed to conform to the requirements ofthe specification.9. Packaging and Package Marking9.1 PackagingWelded wire lath shall be packaged inbundles, rolls, or pallets.9.2 MarkingUnless otherwise required by the purchaseagreement, lath shall have legibly marked thereo

24、n the follow-ing: the product description; the name of the manufacturer ordistributor, country of origin and contact information; thebrand name (if any); and the ASTM designation for theproduct.9.2.1 Each bundle or roll of lath without factory-attachedwater-resistive barrier shall be marked with met

25、al or paper tagssecurely attached to the bundles or with metal tags, paper tags,plastic or metal banding, or paper wrapping on rolls.9.2.2 Each flat sheet and roll of lath with factory-attachedwater-resistive barrier shall be marked on the water-resistivebarrier or face paper attached to the water-r

26、esistive barrier.9.2.3 The quantity for flat sheet bundles shall be squareyards and number of sheets per bundle marked with metal orpaper tags on the pallet or bundle. Rolls shall be marked withmetal tags, paper tags, plastic or metal banding, or paperwrapping on rolls. The marking for flat sheets a

27、nd rolls shallindicate the mesh-opening size and wire thickness of rolls.10. Keywords10.1 lath; metal plaster base; plaster; self-furring lath;stucco; wire lathSUMMARY OF CHANGESCommittee C11 has identified the location of selected changes to this standard since the last issue (C933 14)that may impa

28、ct the use of this standard. (Approved Oct. 1, 2018.)(1) Added Specification E2556/E2556M to list of referenceddocuments (Section 2).(2) Replaced the word “backing” with “factory-attached waterresistive barrier” or “water-resistive barrier” throughout.ASTM International takes no position respecting

29、the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard

30、 is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International

31、Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This

32、 standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 182