ASTM D5003-2018 Standard Test Method for Hardgrove Grindability Index (HGI) of Petroleum Coke.pdf

1、Designation: D5003 06a (Reapproved 2017)D5003 18Standard Test Method forHardgrove Grindability Index (HGI) of Petroleum Coke1This standard is issued under the fixed designation D5003; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONIntroduction of petroleum coke into the coal market in recent years has necessitated the use of manyof th

3、e test methods for coal so like data would be available for comparison and blending purposes.TestMethod D409 does not cover petroleum coke in its scope and its statements of precision and bias donot include petroleum coke. This test method provides the procedures and precision and bias data forthe h

4、ardgrove grindability index (HGI) of petroleum coke. Use of this test method or Test MethodD409 produces the same value for the sample of petroleum coke being analyzed.1. Scope Scope*1.1 This test method covers the determination of the hardgrove grindability index (HGI) of those petroleum cokes that

5、 containno dedusting additive. The procedure for this test method is the same as in Test Method D409. Sections of this test method containthe significance and use of the HGI of petroleum coke, preliminary sample preparation procedures, and procedure and precisionand bias data specific to petroleum c

6、oke.NOTE 1The size consistency (particle size distribution) of fluid petroleum coke is generally 100 % passing a 6.73 mm (No. 3) sieve and greater than80 % passing a 2.00 mm (No. 10) sieve. Much of fluid cokes will pass a 0.59 mm (No. 30) sieve. Because of this fineness the HGI value is related toth

7、e coarser particles in fluid coke and large samples are required to prepare sufficient material of the correct particle size for Test Method D409.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.2.1 ExceptionHardgrove gri

8、ndability index is unitless.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability ofregulator

9、y limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organizati

10、on Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D409 Test Method for Grindability of Coal by the Hardgrove-Machine MethodD4930 Test Method for Dust Control Material on Calcined Petroleum Coke3. Terminology3.1 Definitions:3.1.1 calcined petroleum coke, npetro

11、leum coke that has been thermally treated to drive off the volatile matter and to developcrystalline structure.3.1.2 fluid coke, npetroleum coke with a granular, microscopic layered structure resulting from injection of petroleumfeedstock into a flowing, loose bed of coke particles.1 This test metho

12、d is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.Current edition approved Oct. 1, 2017June 15, 2018. Published November 2017January 20

13、19. Originally approved in 1989. Last previous edition approved in 20112017as D5003 06a (2011).(2017). DOI: 10.1520/D5003-06AR17.10.1520/D5003-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standards

14、volume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to a

15、dequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright AS

16、TM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.3 Hardgrove Grindability Index, HGI, unitless, nin petroleum coke technology, measurement of the relative ease ofpulverizing a raw petroleum coke or green petroleum coke in comparison with coal

17、standards. The higher the HGI value, the easierthe petroleum coke is to grind.3.1.4 petroleum coke, nsolid, carbonaceous residue produced by thermal decomposition of heavy petroleum fractions orcracked stocks, or both.3.1.5 raw petroleum coke, npetroleum coke that has not been calcined.4. Summary of

18、 Test Method4.1 The sample of petroleum coke is reduced (crushed) to produce a high yield of particles passing a 1.19 mm (No. 16) sieveand retained on a 0.59 mm (No. 30) sieve. These particles are reduced in the hardgrove grindability machine according to TestMethod D409. The quantity of particles r

19、etained on a 0.074 mm (No. 200) sieve is used to calculate the HGI of the sample.5. Significance and Use5.1 The HGI is used to predict the ranking of raw petroleum cokes or calcined petroleum cokes in industrial size mills used forcrushing operations. The rankings are based on energy required and fe

20、ed rate or both.5.2 The HGI is also used to select raw petroleum cokes and coals that are compatible with each other when milled together ina blend so that segregation of the blend does not occur during particle size reduction.6. Hazards6.1 Calcined petroleum coke is generally coated with a dedustin

21、g agent to decrease the occurrence and the quantity of dustduring subsequent transporting of the calcined petroleum coke. The dedusting agent is an oil or suitable material. When a dedustingagent is present and is not removed prior to the determination of HGI there can be interference in the sieving

22、 step to measure theportions retained on and passing a 0.074 mm (No. 200) sieve. Removal of the dedusting agent after calcined petroleum coke isreduced to pass the 4.76 mm (No. 4) sieve and before stage crushing to pass the 1.19 mm (No. 16) sieve is required. Suitablesolvents for oil removal are dic

23、hloromethane, dichloroethane and toluene. (WarningSee the appropriate materials safety datasheet.) The solvent used must be removed prior to the reduction to pass the 1.19 mm (No. 16) sieve. Heating to 10 C above theboiling point of the solvent used or application of vacuum is satisfactory for the r

24、emoval.7. Sampling and Sample Preparation7.1 Aguide for sampling petroleum cokes and calcined coke3 and a practice for preparing samples of petroleum coke are in theASTM process of development and will be referenced when they are available. The sample preparation in Test Method D409 isadequate.7.2 W

25、hen a dedusting agent is present remove it in the manner required by the supplier of the calcined petroleum coke. Thesupplier knows what the added agent is, and should best know how to remove it. See Test Method D4930.8. Procedure8.1 The procedure (including apparatus) for raw petroleum coke and for

26、 calcined petroleum coke having no dedusting agent isthe same as listed in Test Method D409.9. Precision and Bias49.1 PrecisionThe statements for repeatability and reproducibility for petroleum coke and calcined petroleum coke are beingdeveloped followingprecision of this test method as determined b

27、y the statistical examination of the interlaboratory test resultsRR:D02-1007. is as follows:9.1.1 RepeatabilityThe difference between successive results obtained by the same operator with the same apparatus underconstant operating conditions on identical test materials would, in the long run, in the

28、 normal and correct operation of the testmethod exceed the following values only in one case in twenty.Repeatability = 2 (1)9.1.2 ReproducibilityThe difference between two single and independent results obtained by different operators working indifferent laboratories on identical material would in t

29、he long run, exceed the following values only in one case in twenty.Reproducibility = 5 for HGI ,=70 (2)Reproducibility = 9 for HGI . 70 (3)3 The guide and practice are being developed by ASTM Committee D02 on Petroleum Products Products, Liquid Fuels, and Lubricants.4 Filed Supporting data have bee

30、n filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1007RR:D02-1892. ContactASTM Customer Service at serviceastm.org.D5003 1829.1.2.1 This precision is valid in the HGI range 35 to 115.9.2 BiasThe procedure in this test method has no bias because the v

31、alue of the hardgrove grindability index can be definedonly in terms of the test method.Bias depends on conformance to the empirical conditions of the test. The ash content must notbe understood to be the same as the mineral content of the petroleum coke.10. Keywords10.1 coke; grindability; petroleu

32、m cokeANNEX(Mandatory Information)A1. TEST METHOD D409A1.1 Test Method D409 is under the jurisdiction of ASTM Committee D05 on Coal and Coke. Committee D02 follows allrevisions and modifications of Test Method D409 through liaison contact with Committee D05.ASTM Committee D02 will reviseother sectio

33、ns of this test method when necessary to conform to changes in Test Method D409.SUMMARY OF CHANGESSubcommittee D02.05 has identified the location of selected changes to this standard since the last issue(D5003 06a (2017) that may impact the use of this standard. (Approved June 15, 2018.)(1) Revised

34、Section 9.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such r

35、ights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additiona

36、l standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the AST

37、M Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 183