IEEE 1159-2009 en Recommended Practice for Monitoring Electric Power Quality《电力质量监测用推荐实施规程》.pdf

1、IEEE Std 1159-2009(Revision of IEEE Std 1159-1995)IEEE Recommended Practice forMonitoring Electric Power Quality IEEE3 Park Avenue New York, NY 10016-5997, USA26 June 2009IEEE Power +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be

2、 obtained through the Copyright Clearance Center. iv Copyright 2009 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 1159-2009, IEEE Recommended Practice for Monitoring Electric Power Quality. This recommended practice encompasses the monitoring of electrical quality

3、 of single-phase and polyphase ac power systems. It is important that all power quality monitors, as well as users of monitors and monitoring data, use consistent terminology and definitions of power quality phenomena. Therefore, this recommended practice provides consistent descriptions of electrom

4、agnetic phenomena occurring on power systems. It describes nominal conditions of the power supply and of deviations from these nominal conditions that may originate within the power supply or in the load equipment or may originate from interactions between the source and the load. Monitoring and mea

5、surements can be utilized for power system performance studies as well as compatibility assessment. Brief, generic descriptions of load susceptibility to deviations from nominal power supply conditions are presented to identify which deviations may be of interest. Further, this recommended practice

6、discusses the selection of appropriate measuring instruments, limitations of these instruments, application techniques, and the interpretation of monitoring results. While there is no implied limitation on the voltage rating of the power system being monitored, signal inputs to monitoring instrument

7、s are generally limited to 1000 V ac root mean square (rms) or less. Instrument transformers and attenuators enable the use of monitoring equipment on a wide range of voltages and currents. Typically, the frequency ratings of the ac power systems being monitored are in the range of 45 Hz to 450 Hz.

8、Some monitors can also acquire dc signals from the load or control system to assist in the interpretation of load response to deviations from the nominal. The interpretation of dc signals is beyond the scope of this recommended practice. It is also recognized that these instruments may perform monit

9、oring functions for environmental conditions (e.g., temperature, humidity, high-frequency electromagnetic radiation); however, the scope of this recommended practice is limited to conducted electrical parameters derived from ac voltage or current measurements, or both. The definitions presented and

10、used in this recommended practice are intended solely for characterizing common electromagnetic phenomena to facilitate communication between various sectors of the power quality community. The definitions are not intended to represent performance standards or equipment tolerances. For example, elec

11、tric power providers (e.g., electric utilities) may utilize different thresholds for undervoltage and overvoltage in the supply from the descriptions in Table 2. On the other hand, sensitive equipment may malfunction due to electromagnetic phenomena that lie within the thresholds of the Table 2 crit

12、eria. Notice to users Laws and regulations Users of these documents should consult all applicable laws and regulations. Compliance with the provisions of this standard does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or r

13、eferring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. v Copyright 2009 IEEE. All rights reserved. Copyrights This document is

14、copyrighted by the IEEE. It is made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making this document availa

15、ble for use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to this document. Updating of IEEE documents Users of IEEE standards should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended

16、from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the curren

17、t edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Standards Association Web site at http:/ieeexplore.ieee.org/xpl/standards.jsp, or contact the IEEE at the address listed previously. For more information about the IEEE Standards Assoc

18、iation or the IEEE standards development process, visit the IEEE-SA Web site at http:/standards.ieee.org. Errata Errata, if any, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/updates/errata/index.html. Users are encouraged to check this

19、URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/interp/ index.html. Patents Attention is called to the possibility that implementation of this recommended practice may require use of subject matter cover

20、ed by patent rights. By publication of this recommended practice, no position is taken with respect to the existence or validity of any patent rights in connection therewith. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inqui

21、ries into the legal validity or scope of Patents Claims or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or nondiscriminatory. Users of this recommended practice are express

22、ly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. vi Copyright 2009 IEEE. All rights reserved. Participants At the time this r

23、ecommended practice was submitted for approval, the Electric Power Quality Monitoring Working Group had the following membership: E. R. (Randy) Collins, Jr., Chair Timothy D. Unruh, Vice Chair Richard Bingham Math Bollen James Bouford Reuben Burch Gary Chang Charles DeNardo Russell Ehrlich Thomas Ge

24、ntile Erich Gunther Mark Halpin Dennis Hansen Fred Hensley John Kennedy Harold Kirkham Joseph L. Koepfinger Michael Lowenstein Alexander McEachern W. A. Moncrief David Mueller Ram Mukherji Marty Page Charles Perry Dan Sabin Andrew Sagl Bob Saint Kenneth Sedziol Michael Shepherd James Wikston Charles

25、 Williams Wilsun Xu The following members of the individual balloting committee voted on this recommended practice. Balloters may have voted for approval, disapproval, or abstention. William J. Ackerman Steven Alexanderson Ali Al Awazi Thomas Basso David Beach Kenneth Behrendt Wallace Binder Richard

26、 Bingham James Bouford Steven Brockschink Chris Brooks William Brumsickle Gustavo Brunello Reuben Burch William Byrd Mario Manana Canteli Wen-Kung Chang Edward Collins Michael Comber Tommy Cooper Luis Coronado A. Csomay Charles Denardo F. A. Denbrock Randall Dotson Neal Dowling Donald Dunn Russell E

27、hrlich Gearold O. H. Eidhin Gary Engmann C. Erven Dan Evans Thomas Field James Funke James Gardner Thomas Grebe Randall Groves Ajit Gwal Daryl Hallmark Dennis Hansen Kenneth Hanus Adrienne Hendrickson Werner Hoelzl Farshad Hormozi R. Jackson Innocent Kamwa Piotr Karocki Gael Kennedy John Kennedy Jos

28、eph L. Koepfinger David W. Krause Jim Kulchisky Scott Lacy Chung-Yiu Lam Albert Livshitz Michael Lowenstein G. Luri Keith Malmedal Alexander McEachern Gary Michel W. A. Moncrief David Mueller Jerry Murphy Michael S. Newman Joe Nims Gregory Olson Marty Page Neal Parker Bansi Patel Charles Perry Dean

29、Philips Percy Pool Iulian Profir Michael Roberts Charles Rogers Thomas Rozek Bob Saint Bartien Sayogo Kenneth Sedziol Cata Slatineanu James E. Smith Jerry Smith Aaron Snyder John Spare K. Stump Michael Swearingen S. Thamilarasan Demetrios Tziouvaras Eric Udren Timothy Unruh John Vergis Reigh Walling

30、 Daniel Ward Larry Yonce Larry Young Donald Zipse Ahmed Zobaa vii Copyright 2009 IEEE. All rights reserved. When the IEEE-SA Standards Board approved this recommended practice on 18 March 2009, it had the following membership: Robert M. Grow, Chair Thomas Prevost, Vice Chair Steve M. Mills, Past Cha

31、ir Judith Gorman, Secretary John Barr Karen Bartleson Victor Berman Ted Burse Richard DeBlasio Andy Drozd Mark Epstein Alexander Gelman Jim Hughes Richard H. Hulett Young Kyun Kim Joseph L. Koepfinger* John Kulick David J. Law Ted Olsen Glenn Parsons Ronald C. Petersen Narayanan Ramachandran Jon Wal

32、ter Rosdahl Sam Sciacca *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Howard L. Wolfman, TAB Representative Michael Janezic, NIST Representative Satish K. Aggarwal, NRC Representative Don Messina IEEE Standards Project Editor Matthew J. Ceglia IEEE Stan

33、dards Program Manager, Technical Program Development viii Copyright 2009 IEEE. All rights reserved. Contents 1. Overview 1 1.1 Scope . 1 1.2 Purpose 1 2. Normative references 2 3. Definitions 2 4. Power quality phenomena 3 4.1 Introduction . 3 4.2 Electromagnetic compatibility. 3 4.3 General classif

34、ication of phenomena. 4 4.4 Detailed descriptions of phenomena 5 5. Monitoring objectives. 23 5.1 Introduction . 23 5.2 Need for monitoring power quality . 24 5.3 Equipment tolerances and effects of disturbances on equipment 25 5.4 Equipment types 25 5.5 Effect on equipment by phenomena type. 26 6.

35、Measurement instruments. 29 6.1 Introduction . 29 6.2 Historyfour generations . 30 6.3 Reasons to monitor versus type of monitor . 30 6.4 Parameters to be measured 30 6.5 Monitoring instruments . 33 6.6 Pitfalls/Cautions. 38 6.7 Safety. 39 7. Application techniques . 39 7.1 Safety. 40 7.2 Monitoring

36、 location . 43 7.3 Equipment connection . 46 7.4 Measurement thresholds 51 8. Interpreting power monitoring results 55 8.1 Introduction . 55 8.2 Interpreting data summaries 56 8.3 Critical data extraction. 57 8.4 Interpreting critical events . 61 8.5 Verifying data interpretation 70 Annex A (informa

37、tive) Calibration and self-testing. 72 A.1 Introduction 72 A.2 Calibration issues 73 Annex B (informative) Glossary 75 Annex C (informative) Bibliography 79 1 Copyright 2009 IEEE. All rights reserved. IEEE Recommended Practice for Monitoring Electric Power Quality IMPORTANT NOTICE: This standard is

38、not intended to ensure safety, security, health, or environmental protection in all circumstances. Implementers of the standard are responsible for determining appropriate safety, security, environmental, and health practices or regulatory requirements. This IEEE document is made available for use s

39、ubject to important notices and legal disclaimers. These notices and disclaimers appear in all publications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE

40、or viewed at http:/standards.ieee.org/IPR/ disclaimers.html 1. Overview 1.1 Scope This recommended practice encompasses the monitoring of electrical characteristics of single-phase and polyphase ac power systems. It includes consistent descriptions of conducted electromagnetic phenomena occurring on

41、 power systems. This recommended practice presents definitions of nominal conditions and deviations from these nominal conditions that may originate within the source of supply or load equipment or may originate from interactions between the source and the load. Also, this recommended practice discu

42、sses measurement techniques, application techniques, and the interpretation of monitoring results. 1.2 Purpose The use of equipment that causes and is susceptible to various electromagnetic phenomena has heightened the interest in power quality. An increase in operational problems has led to a varie

43、ty of attempts to describe the phenomena. Because different segments of the technical community have used different terminologies to describe these electromagnetic events, this recommended practice provides users with a consistent set of terms and definitions for describing these events. An understa

44、nding of how power quality events impact the power system and end-use equipment is required in order to make monitoring useful. Proper measuring techniques are required to safely obtain useful, accurate data. Appropriate location of monitors, systematic studies, and interpretation of results will en

45、hance the value of power quality monitoring. The purpose of this recommended practice is to assist users as well as equipment and software manufacturers and vendors by describing techniques for defining, measuring, quantifying, and interpreting electromagnetic disturbances on the power system. IEEE

46、Std 1159-2009 IEEE Recommended Practice for Monitoring Electric Power Quality 2 Copyright 2009 IEEE. All rights reserved. 2. Normative references The following referenced documents are indispensable for the application of this recommended practice (i.e., they must be understood and used; therefore,

47、each referenced document is cited in text and its relationship to this recommended practice is explained). For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments or corrigenda) applies. No normative refere

48、nces apply to this recommended practice. 3. Definitions For the purposes of this recommended practice, the following terms and definitions apply. The Authoritative Dictionary of IEEE Standards Terms B181should be referenced for terms not defined in this clause. 3.1 flicker: Impression of unsteadines

49、s of visual sensation induced by a light stimulus whose luminance or spectral distribution fluctuates with time. 3.2 fundamental (component): The component of an order 1 (e.g., 50 Hz, 60 Hz) of the Fourier series of a periodic quantity. 3.3 imbalance (voltage or current): The ratio of the negative sequence component to the positive sequence component, usually expressed as a percentage. Syn: unbalance (voltage or current) 3.4 impulsive transient: A sudden nonpower frequency change in the steady-state condition of voltage or current that is unidirectional in polarity (prim