IEEE 1187-2013 en Recommended Practice for Installation Design and Installation of Valve-Regulated Lead-Acid Batteries for Stationary Applications《固定设备用的阀调节铅酸电池.pdf

1、 IEEE Recommended Practice for Installation Design and Installation of Valve-Regulated Lead-Acid Batteries for Stationary Applications Sponsored by the Stationary Batteries Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 1187-2013 (Revision of IEEE Std

2、 1187-2002) IEEE Std 1187-2013 (Revision of IEEE Std 1187-2002) IEEE Recommended Practice for Installation Design and Installation of Valve-Regulated Lead-Acid Batteries for Stationary Applications Sponsor Stationary Batteries Committee of the IEEE Power and Energy Society Approved 11 December 2013

3、IEEE-SA Standards Board Abstract: Guidance for the installation and installation design of valve-regulated lead-acid (VRLA) batteries is provided in this recommended practice. This recommended practice is intended for all standby stationary installations. However, specific applications, such as emer

4、gency lighting units and semi-portable equipment, may have other appropriate practices and are beyond the scope of this recommended practice. Alternative energy applications are not covered. Keywords: acceptance test, battery capacity, battery installation, battery installation design, battery maint

5、enance, battery terminal voltage, battery testing, connection resistance measurements, float voltage, IEEE 1187, internal ohmic measurements, standby power applications, valve-regulated lead-acid battery The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-59

6、97, USA Copyright 2014 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 11 March 2014. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, ef

7、fectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard doe

8、s not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developme

9、nts in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other

10、person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a gi

11、ven IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEOR

12、Y OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations T

13、he IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processe

14、d in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied on as, a formal position of IEEE. At lectures, symposia, seminars, or educational course

15、s, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interes

16、ted party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. S

17、ince IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide

18、an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE wor

19、king group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any I

20、EEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in comp

21、liance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. The

22、se include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in

23、 copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of lic

24、ensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEE

25、E Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time con

26、sists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that

27、 its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended thr

28、ough the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standar

29、ds.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementat

30、ion of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of a

31、ssurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or

32、under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Es

33、sential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are

34、 reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. vi Copy

35、right 2014 IEEE. All rights reserved. Participants At the time this recommended practice was submitted to the IEEE-SA Standards Board for approval, the VRLA Battery Installation Working Group had the following membership: John Polenz, Chair Allen Byrne, Vice Chair Edward Amato Curtis Ashton Gary Bal

36、ash William Cantor Terry Chapman Troy Chatwin Pete Demar Paul Anthonius Cornelis Hectors John Kopera Daniel Lambert Stephen McCluer Daniel McMenamin Robert Schmidt Richard Tressler Lesley Varga Stephen Vechy The following members of the individual balloting committee voted on this recommended practi

37、ce. Balloters may have voted for approval, disapproval, or abstention. Michael Adams Samuel Aguirre Edward Amato Phyllis Archer Curtis Ashton Gary Balash Thomas Barnes Robert Beavers Steven Bezner John Bonner Derek Brown Nissen Burstein William Bush William Cantor Paul Cardinal Larry Carson Leonard

38、Casella Terry Chapman Troy Chatwin Mark Clark Garth Corey Charles Cotton Mark Crisler Ray Davis Peter Demar Gary Donner Randall Dotson Neal Dowling Sourav Dutta Charles Finin Robert Fletcher John Gagge Doaa Galal David Gilmer James Gleason Joseph Gravelle Randall Groves Ajit Gwal Paul Anthonius Corn

39、elis Hectors Scott Hietpas David Horvath David Ittner Alan Jensen Wayne Johnson Gael Kennedy James Kinney Jim Kulchisky Saumen Kundu Thomas Ladson Chung-Yiu Lam Jeffrey LaMarca Daniel Lambert Michael Lauxman Greg Luri Jose Marrero John McAlhaney William McBride Stephen McCluer Daniel McMenamin Peter

40、 McNutt Larry Meisner Kimberly Mosley Haissam Nasrat Dennis Neitzel Arthur Neubauer Michael Newman Charles Ngethe Joe Nims Gary Nissen Lorraine Padden Bansi Patel Roger Pocock John Polenz Shawn Pryer Edward Rafter John Randolph Jan Reber Michael Roberts Charles Rogers Steven Sano Bartien Sayogo Robe

41、rt Schmidt Robert Schuerger Christo Searles Robert Seitz Gil Shultz David Singleton David Smith Jeremy Smith Gary Stoedter Richard Tressler Eric Udren Lesley Varga Stephen Vechy John Vergis Kenneth White Jian Yu Ahmed Zobaa vii Copyright 2014 IEEE. All rights reserved. When the IEEE-SA Standards Boa

42、rd approved this recommended practice on 11 December 2013, it had the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Stephen Dukes Jean-Philippe Faure Alexander Ge

43、lman Mark Halpin Gary Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan*Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board l

44、iaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Michelle Turner IEEE Standards Program Manager, Document Development Malia Zaman IEEE Standards Program Manager, Technical Program Developer viii Copyright 2014 IEEE. All rights reserved. Introduction This introductio

45、n is not part of IEEE Std 1187-2013, IEEE Recommended Practice for Installation Design and Installation of Valve-Regulated Lead-Acid Batteries for Stationary Applications. Guidance for the installation and installation design of valve-regulated lead-acid (VRLA) batteries is provided in this recommen

46、ded practice. This recommended practice is intended for all standby stationary installations. However, specific applications, such as emergency lighting units and semi-portable equipment, may have other appropriate practices and are beyond the scope of this recommended practice. Alternative energy a

47、pplications are not covered. ix Copyright 2014 IEEE. All rights reserved. Contents 1. Overview . 1 1.1 Scope 1 1.2 Purpose . 2 2. Normative references . 2 3. Definitions, acronyms, and abbreviations 3 3.1 Definitions 3 3.2 Acronyms and abbreviations . 3 4. Safety . 4 4.1 General 4 4.2 Electrical haz

48、ards 4 4.2.1 Shock hazard . 4 4.2.2 Ground fault detection . 4 4.2.3 Arc flash hazard 5 4.3 Chemical hazards 5 4.4 Thermal hazards 6 4.5 Lifting and handling hazards 6 4.6 Personal protective equipment (PPE) . 6 5. Installation design criteria 6 5.1 Location 7 5.1.1 General considerations 7 5.1.2 De

49、sign for maintainability . 7 5.2 Mounting. 8 5.3 Seismic 8 5.4 Ventilation 9 5.4.1 Ventilation for temperature control . 9 5.4.2 Ventilation for hydrogen control . 9 5.5 Instrumentation, controls, and alarms . 10 5.5.1 Instrumentation . 10 5.5.2 Controls . 10 5.5.3 Alarms . 10 5.6 Parallel-battery strings 11 5.7 Charging . 11 5.8 Battery protection . 12 5.8.1 General 12 5.8.2 Additional considerations for parallel battery strings 12 6. Installation procedures . 12 6.1 Receiving and storage . 12 6.1.1 Receiving inspection . 12 6.1.2 Unpacking . 12 6.1.3 Storage 13 6.2 Assemb