IEEE 1235-2000 en Guide for the Properties of Identifiable Jackets for Underground Power Cables and Ducts《地下电力电缆和管道用可识别护套的性能指南》.pdf

1、Copyright 1998 IEEE All Rights Reserved 1IEEE Std 1235-2000 (R20)IEEE Guide for the Properties of Identifiable Jackets for Underground Power Cables and DuctsSponsorInsulated Conductors Committeeof theIEEE Power Engineering SocietyApproved 20 June 2000Reaffirmed HFember 20IEEE-SA Standards BoardAbstr

2、act: Identification markings of jacketed underground power cables and ducts are established in this guide.Included are various methods of identifying underground power cables and ducts, and the visual, chemical, andmechanical properties of the identification materials and/or methods, and their impac

3、t on the properties of the overalljacket or duct as well as their impact on installation practices.Keywords: duct, identification, jacket, power cables, raised ridge, red stripeThe Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2000 by the

4、 Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 10 October 2000. Printed in the United States of America.Print: ISBN 0-7381-2502-4 SH94860PDF: ISBN 0-7381-2503-2 SS94860No part of this publication may reproduced in any form, in an electronic retrieval system or

5、 otherwise, without theprior written permission of the publisher.IEEE Standardsdocuments are developed within the IEEE Societies and the Standards Coordinating Com-mittees of the IEEE Standards Association (IEEE-SA) Standards Board. Members of the committees servevoluntarily and without compensation

6、. They are not necessarily members of the Institute. The standardsdeveloped within IEEE represent a consensus of the broad expertise on the subject within the Institute aswell as those activities outside of IEEE that have expressed an interest in participating in the development ofthe standard.Use o

7、f an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that thereare no other ways to produce, test, measure, purchase, market, or provide other goods and services related tothe scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a standard

8、is approved andissued is subject to change brought about through developments in the state of the art and commentsreceived from users of the standard. Every IEEE Standard is subjected to review at least every five years forrevision or reaffirmation. When a document is more than five years old and ha

9、s not been reaffirmed, it is rea-sonable to conclude that its contents, although still of some value, do not wholly reflect the present state ofthe art. Users are cautioned to check to determine that they have the latest edition of any IEEE Standard.Comments for revision of IEEE Standards are welcom

10、e from any interested party, regardless of membershipaffiliation with IEEE. Suggestions for changes in documents should be in the form of a proposed change oftext, together with appropriate supporting comments.Interpretations: Occasionally questions may arise regarding the meaning of portions of sta

11、ndards as theyrelate to specific applications. When the need for interpretations is brought to the attention of IEEE, theInstitute will initiate action to prepare appropriate responses. Since IEEE Standards represent a consensus ofall concerned interests, it is important to ensure that any interpret

12、ation has also received the concurrence of abalance of interests. For this reason, IEEE and the members of its societies and Standards CoordinatingCommittees are not able to provide an instant response to interpretation requests except in those cases wherethe matter has previously received formal co

13、nsideration. Comments on standards and requests for interpretations should be addressed to:Secretary, IEEE-SA Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAIEEE is the sole entity that may authorize the use of certification marks, trademarks, or other designations toindicate c

14、ompliance with the materials set forth herein.Authorization to photocopy portions of any individual standard for internal or personal use is granted by theInstitute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to CopyrightClearance Center. To arrange for p

15、ayment of licensing fee, please contact Copyright Clearance Center,Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (978) 750-8400. Permission to photo-copy portions of any individual standard for educational classroom use can also be obtained through theCopyright Clearance Center.Note:

16、Attention is called to the possibility that implementation of this standard mayrequire use of subject matter covered by patent rights. By publication of this standard,no position is taken with respect to the existence or validity of any patent rights inconnection therewith. The IEEE shall not be res

17、ponsible for identifying patents forwhich a license may be required by an IEEE standard or for conducting inquiries intothe legal validity or scope of those patents that are brought to its attention.Copyright 2000 IEEE. All rights reserved.iiiIntroduction(This introduction is not part of IEEE Std 12

18、35-2000, IEEE Guide for the Properties of Identifiable Jackets for Under-ground Power Cables and Ducts.)This guide is concerned with the identification of a jacket as it is defined in The IEEE Standard Dictionary ofElectrical and Electronic Terms, Sixth Edition (“A thermoplastic or thermosetting pla

19、stic covering, some-times fabric reinforced, applied over the insulation, core, metallic sheath, or armor of a cable”). Users shouldnote that this guide makes reference to standards developed by the Insulated Cable Engineers Association(ICEA), and other organizations.This guide is written for the ma

20、ny persons with responsibilities for selecting underground power cablejackets and ducts. The purpose of the guide is to present methods for defining and selecting red stripes orraised ridges used in conjunction with underground power cable and duct. Other methods of power cable andduct identificatio

21、n, all red jackets, stripes other than red, and the National Electrical Safety Code identifierare beyond the scope of this guide and will not be covered in this guide.At the time this guide was completed, the Working Group on the Properties of Identifiable Jackets forUnderground Power Cables and Duc

22、ts had the following membership:S. R. Szaniszlo,ChairE. E. Walcott,Co-ChairThe following members of the balloting committee voted on this standard:T. ArnoldR. S. BakerP. BloyedJ. E. Cherry M. L. Dyer J. V. FitzgeraldR. E. Fleming J. M. HansD. R. Jeter L. J. Kelly F. L. Kuchta F. E. LaGase M. E. Lowe

23、ll E. P. Marsden H. A. MayerW. PetersonJ. PickeringE. PerezK. W. PrierC. K. ShortR. L. SilvermanJ. H. SnowH. J. Soleski, Jr.J. C. SpenceG. J. StanoC. ThompsonD. TomaszewskiH. T. VollkommerJ. N. WareTorben AaboTheodore A. BalaskaMartin BaurM. Thomas BlackDavid T. BogdenKenneth E. BowHarvey L. BowlesK

24、ent W. BrownPaul S. CardelloJack E. CherryJohn H. CooperJames M. DalyRuss C. DantzlerMarcel FortinKenneth HancockRichard L. HarpStanley V. HeyerLauri J. HiivalaLawrence J. KellyCarl LandingerMark E. LowellMatthew S. MashikianJohn E. Merando, Jr.Shantanu NandiArthur V. Pack, Jr.Dennis C. PrattPeter R

25、alstonGilbert L. SmithHenry J. SoleskiPeter W. SpencerOrloff W. StyveDuc B. TrinhRoland H. W. WatkinsCarl J. WentzelJohn L. WhiteWilliam D. WilkensJoseph T. ZimnochivCopyright 2000 IEEE. All rights reserved.When the IEEE-SA Standards Board approved this standard on 20 June 2000, it had the following

26、membership:Donald N. Heirman,ChairJames T. Carlo,Vice ChairJudith Gorman,Secretary*Member EmeritusAlso included is the following nonvoting IEEE-SA Standards Board liaison:Alan Cookson, NIST RepresentativeDonald R. Volzka, TAB RepresentativeAndrew D. IckowiczIEEE Standards Project EditorSatish K. Agg

27、arwalMark D. BowmanGary R. EngmannHarold E. EpsteinH. Landis FloydJay Forster*Howard M. FrazierRuben D. GarzonJames H. GurneyRichard J. HollemanLowell G. JohnsonRobert J. KennellyJoseph L. Koepfinger*Peter H. LipsL. Bruce McClungDaleep C. MohlaJames W. MooreRobert F. MunznerRonald C. PetersenGerald

28、H. PetersonJohn B. PoseyGary S. RobinsonAkio TojoDonald W. ZipseCopyright 2000 IEEE. All rights reserved.vContents1. Overview 11.1 Scope 11.2 Purpose. 22. References 23. Dimensional criteria. 33.1 Red stripe . 33.2 Raised ridge . 34. Measurement technique . 34.1 Red stripe . 34.2 Raised ridge . 35.

29、Color stability. 45.1 Outdoor color stability . 45.2 In-ground color stability 46. Additional markings. 57. Physical properties. 57.1 Red stripe . 57.2 Raised ridge . 58. Storage criteria. 69. Duct for power cable 69.1 Duct 6viCopyright 2000 IEEE. All rights reserved.Copyright 2000 IEEE. All rights

30、reserved.1IEEE Guide for the Properties of Identifiable Jackets for Underground Power Cables and Ducts1. OverviewMany methods have been used to identify underground power cables and ducts. They range from markertapes, raised ridges, indent printing, and colored or striped jackets. In 1993, the Natio

31、nal Electrical SafetyCode(NESC) adopted rule 350G, which applies to all direct buried jacketed supply cable meeting rule350B and all direct buried communication cables. NESCrule 350G stipulates a lightning bolt be indentedor embossed in the outermost cable jacket of supply cable or duct at a repeati

32、ng frequency of not more than1 meter (40 inches). The symbol may be sequentially combined with other data or symbols, or both, printedon the jacket, but shall be separated as indicated in Figure 350-1 of the NESC. Some utilities are usingadditional identification, such as red stripes or raised ridge

33、s, to supplement the NESCrequirement.It is left to the utilitys discretion to determine the appropriate type of cable identification, as well as whatsize and type installation merits being identified. Since the red stripes and raised ridges are extruded (or co-extruded) with the outer protective jac

34、ket material, it is the intent of this guide to ensure that the red stripematerials be fully compatible and firmly bonded to the overall outer protective jackets or ducts. The redstripes should not discolor significantly during limited outdoor storage of cable reels at cable manufacturersand utiliti

35、es, or when buried underground. This guide recommends 1000 hours Xenon-Arc aging to demon-strate acceptable outdoor exposure, and 672 hours aging at 60 C in tap water, 5% hydrochloric acid (HCL)solution, and 5% sodium hydroxide (NaOH) to demonstrate acceptable color stability when buried.1.1 ScopeTh

36、is guide provides recommendations for red stripe and raised ridge identification markings on insulatingand semiconducting linear low density polyethylene (LLDPE), medium density polyethylene (MDPE), highdensity polyethylene (HDPE) and polyvinyl chloride (PVC) jacketed underground power cables, and H

37、DPEduct containing jacketed or unjacketed underground power cables. The red stripe recommendations includethe number of stripes, color, width, thickness, retention characteristics, physical properties, storage criteria,and testing methods. The raised ridge recommendations include physical properties

38、, width, height, andcircumferential spacing. It is the intent of this guide to provide a minimum level of physical, chemical, andcolor durability on red stripes used to identify underground power cables and ducts.IEEEStd 1235-2000 IEEE GUIDE FOR THE PROPERTIES OF IDENTIFIABLE2Copyright 2000 IEEE. Al

39、l rights reserved.1.2 PurposeJacketed underground power cables and their related duct systems are similar in size and appearance tocommunication cables and underground pipes. Identification and differentiation of underground powercables and ducts has been attempted by marker tapes, raised ridges, in

40、dent printing, colors (other thanblack), and striped jackets. In the absence of a standard or guide on the properties of red stripes used as iden-tification markings, some utilities have reported that red stripes whiten after limited (in some cases, less thanone year) outdoor storage. This guide pro

41、vides recommendations for the properties, design, dimensionalrequirements, and testing of red stripes used as identification markings on underground power cables andducts. In addition, this guide provides physical attribute recommendations for raised ridge identification.2. ReferencesThis guide shal

42、l be used in conjunction with the following references. When the following standards aresuperseded by an approved revision, the revision shall apply:Accredited Standards Committee C2-1997, National Electrical Safety Code(NESC).1ANSI/ICEA S-94-649-1997, Standard for Concentric Neutral Cables, 546 kV.

43、2ASTM G66-99, Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of5XXX Series Aluminum Alloys (ASSET Test).3ASTM D1712-96, Standard Practice for Resistance of Plastics to Sulfide Staining.NEMA WC3-1992/ICEA S-19-81, Rubber-Insulated Wire and Cable for the Transmissio

44、n and Distributionof Electrical Energy (Rev.1, 1994).4NEMA WC5-1992/ICEA S-61-402, Thermoplastic-Insulated Wire and Cable for the Transmission andDistribution of Electrical Energy (Rev. 2, 1996).NEMA WC7-1988/ICEA S-66-524, Cross-Linked-Thermosetting-Polyethylene-Insulated Wire and Cablefor the Tran

45、smission and Distribution of Electrical Energy (Rev. 4, 1998).NEMA WC8-1988/ICEA S-68-516, Ethylene-Propylene-Rubber-Insulated Wire and Cable for the Trans-mission and Distribution of Electrical Energy (Rev. 3, 1996).UL 44-1999, UL Standard for Safety for Thermoset-Insulated Wires and Cables.5UL 107

46、2-1997, UL Standard for Safety for Medium-Voltage Power Cables.UL 1569-2000, UL Standard for Safety for Metal-Clad Cables.1The NESC is available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ08855-1331, USA (http:/standards.ieee.org/).2ANSI p

47、ublications are available from the Sales Department, American National Standards Institute, 11 West 42nd Street, 13th Floor,New York, NY 10036, USA (http:/www.ansi.org/). ICEA publications are available from ICEA, P.O. Box 20048, Minneapolis, MN55420, USA (http:/www.icea.org/).3ASTM publications are

48、 available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken,PA 19428-2959, USA (http:/www.astm.org/). 4NEMA publications are available from Global Engineering Documents, 15 Inverness Way East, Englewood, Colorado 80112, USA(http:/ standards are available

49、from Global Engineering Documents, 15 Inverness Way East, Englewood, Colorado 80112, USA(http:/ FOR UNDERGROUND POWER CABLES AND DUCTS Std 1235-2000Copyright 2000 IEEE. All rights reserved.33. Dimensional criteria3.1 Red stripeWhere red stripe identification is specified, there should be three (3) longitudinal red stripes spaced approxi-mately 120 apart, extruded into the outer protective jacket or duct.The thickness of the measured extruded red stripes may vary from 0.125 mm to 0.635