IEEE 1653 6-2013 en Trial-Use Recommended Practice for Grounding of DC Equipment Enclosures in Traction Power Distribution Facilities《动力配电设施中直流设备附件接地用IEEE试验用推荐性.pdf

1、 IEEE Trial-Use Recommended Practice for Grounding of DC Equipment Enclosures in Traction Power Distribution Facilities Sponsored by the Rail Transportation Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Vehicular Technology Society IEEE Std 1653.6-2013 IEEE Std 1653.6-2013

2、IEEE Trial-Use Recommended Practice for Grounding of DC Equipment Enclosures in Traction Power Distribution Facilities Sponsor Rail Transportation Standards Committee of the IEEE Vehicular Technology Society Approved 11 December 2013 IEEE-SA Standards Board Abstract: The grounding of dc equipment en

3、closures installed in dc traction power distribution facilities as well as related insulation treatments required for solid and resistance grounding methods are covered in this standard. Guidelines are also given for material, installation, and testing of insulation used in dc traction facilities an

4、d further recommended criteria for acceptability are provided. System grounding, though related, is not covered in this document. Keywords: 64, 64GS, 64HS, 64M, 64MR, bonding, building enclosure, dc, dc circuit breakers, device 64, diode ground, direct current, distribution facilities, electric trol

5、ley bus, enclosure ground, equipment enclosure, equipment ground, ETB, floor insulation, ground, ground protection, ground relay, grounded structure, grounding, GS, heavy rail, high resistance, high-resistance grounding, hot structure, HS, IEEE 1653.6, insulation dielectric test, insulation testing,

6、 light rail, low resistance, low-resistance grounding, low-voltage equipment, negative return, rail transit, rectifier, single-point grounding, switchgear, system grounding, traction power, transfer trip, wall insulation The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New

7、York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 December 2013. Printed in the United States of America. IEEE and NESC are registered trademarks in the U.S. Patent fitness for a particular purpose; non-infringeme

8、nt; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The exis

9、tence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change br

10、ought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perfor

11、m any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determinin

12、g the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HO

13、WEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WA

14、S FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written

15、or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia,

16、seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documen

17、ts are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with app

18、ropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Comm

19、ittees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcom

20、e to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Complian

21、ce with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to

22、urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of bo

23、th public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IE

24、EE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only

25、. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Cl

26、earance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE do

27、cument at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it

28、 is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and

29、whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the I

30、EEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to t

31、he possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent appli

32、cant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent

33、rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not

34、 responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or

35、in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE

36、 Standards Association. Copyright 2013 IEEE. All rights reserved. vi Participants At the time this IEEE trial-use recommended practice was completed, the 1653.6 Working Group had the following membership: Ethan Kim, Chair Paul Forquer, Vice Chair Roger Avery William Aycock Steven Bezner Alan Blatchf

37、ord Radomir Bulayev Steve Cavallo Yunxiang Chen Vasant Chokshi Ron Clark Ray Davis Mike Dinolfo Earl Fish John Fish Rajen Ganeriwal Charles Garten Michael Girdwood David R. Gobelle Lowell Goudge John Grantham David Groves Steve Hamilton Bob Jaccino Sharon James Mladen Jeftic Andrew Jones Saumen Kund

38、u Michael Lam Ming Li Thomas Li Louie Luo Abdullah Mahmud Jack Martin Sujeet Mishra Craig Norman Constantinos Orphanides Moustapha Ouattara Henry Oviedo John Pascu Dev Paul Charles Ross Edward Rowe Narendra Shah Mohinder Sharma Lee Shostle Suresh Shrimavle Jeffrey Sisson Ralph Stell Rick Straubel Ra

39、ymond Strittmatter Gary Touryan Jeffrey Wharton Robert Wilson Dave Wong Tom Young Gordon Yu Kelvin Zan Matthew Zeedyk The following members of the individual balloting committee voted on this trial-use recommended practice. Balloters may have voted for approval, disapproval, or abstention. William A

40、ycock Steven Bezner William Bush William Byrd Keith Chow Timothy Cramond Ray Davis Mike Dinolfo Paul Forquer H. Glickenstein Lowell Goudge Randall Groves Werner Hoelzl Walter Keevil Yuri Khersonsky Ethan Kim Jim Kulchisky Saumen Kundu Thomas Kurihara Greg Luri Sujeet Mishra Michael Newman Mark Pfeif

41、fer Jesse Rorabaugh Charles Ross Edward Rowe Bartien Sayogo Suresh Shrimavle James Smith Ralph Stell Raymond Strittmatter Gary Touryan Joe Uchiyama John Vergis Kenneth White Paul White Robert Wilson Jian Yu Matthew Zeedyk Copyright 2013 IEEE. All rights reserved. viiWhen the IEEE-SA Standards Board

42、approved this trial-use recommended practice on 11 December 2013, it had the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Ph

43、ilippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting

44、 IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE Standards Program Manager, Document Development Michael Kipness IEEE Standards Program Manager, Technical Program Development Copyright 2013 IEEE. All rights reserved. vi

45、ii Introduction This introduction is not part of IEEE Std 1653.6-2013, IEEE Trial-Use Recommended Practice for Grounding of DC Equipment Enclosures in Traction Power Distribution Facilities. This document contains recommended practices for grounding and bonding of dc equipment enclosures installed w

46、ithin traction power distribution facilities where the conventional practice in most dc traction power systems is to isolate both the positive and negative poles from ground. There exists a variety of system grounding methods, including single-point grounding, positive- or negative-pole grounding, r

47、esistive grounding, diode grounding, etc; however, details on system grounding and related applications, e.g., stray current control, rail-to-ground protective relay devices, are not covered by the scope of this document. For additional information regarding transit power systems grounding, refer to

48、 IEEE Std 142, IEEE Recommended Practice for Grounding of Industrial and Commercial Power Systems.a,b,cThe necessity of this recommended practice stems from the lack of uniformity of enclosure grounding practices in the dc traction industry. Furthermore, grounding of dc traction equipment enclosures

49、 is not covered in the National Electric Code B4dand National Electrical Safety Code B2. As such, the goal of this document is to provide users with the various grounding methods used specifically for grounding dc traction equipment enclosures and preparing dc traction distribution facilities when implementing these grounding methods. The organization of this document follows a typical equipment layout within a dc traction distribution facility. The main sections include ac equipment enclosures, dc equipment enclosures, floor insulation, and wall insulation. Refer to