IEEE 1732-2017 en Recommended Practice for Space Charge Measurements on High- Voltage Direct-Current Extruded Cables for Rated Voltages up to 550 kV.pdf

1、IEEE Recommended Practice for Space Charge Measurements on High- Voltage Direct-Current Extruded Cables for Rated Voltages up to 550 kV IEEE Std 1732-2017 IEEE Dielectrics and Electrical Insulation Society Sponsored by the Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std 17

2、32-2017 IEEE Recommended Practice for Space Charge Measurements on High- Voltage Direct-Current Extruded Cables for Rated Voltages up to 550 kV Sponsor Standards Committee of the IEEE Dielectrics and Electrical Insulation Society Approved 23 March 2017 IEEE-SA Standards BoardAbstract: The aim of thi

3、s recommended practice is establishing a protocol for the measurement of space charges in high-voltage direct-current (HVDC) extruded cables having rated voltage up to 550 kV. Such measurements are prescribed to be carried out at the beginning and at the end of load cycle qualification tests (either

4、 the long-duration voltage test of prequalification tests or the load cycle test of type tests). The various steps of the protocol for the measurement of space charges in such cables are carefully described. Details are given about the procedure for applying and switching off the voltage, the prepar

5、ation and conditioning of specimens, the measurement times during poling and depolarization, and the calculations for checking electric field stabilization. The ultimate goal of this recommended practice is not verifying the compliance with any maximum acceptable limit of either space charge or elec

6、tric field, but rather assessing the variation of the electric field profile in the cable insulation wall during load cycle qualification tests. Keywords: HVDC extruded insulation, IEEE 1732, power cables, power cable testing, space charge measurements The Institute of Electrical and Electronics Eng

7、ineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2017 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 30 June 2017. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purp

8、ose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly

9、voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is s

10、ubject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE un

11、dertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent profess

12、ional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINE

13、SS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHE

14、THER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2017 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the ap

15、proved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be rel

16、ied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Commen

17、ts on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should

18、 be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE a

19、nd the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would

20、 like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documen

21、ts should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements.

22、 IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws. They are ma

23、de available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for

24、 use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2017 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of a

25、ny individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portion

26、s of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be

27、amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least

28、every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest ed

29、ition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For m

30、ore information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html.

31、Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existe

32、nce or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Lette

33、rs of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses

34、 Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any

35、licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringeme

36、nt of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2017 IEEE. All rights reserved. Participants At the time this IEEE recommended practice was completed, the DEI/SC/HVDC Cable Systems Working Group had the foll

37、owing membership: Giovanni Mazzanti, Chair Massimo Marzinotto, Vice Chair Jerome Castellon George Chen John Fothergill Mingli Fu Naohiro Hozumi June-Ho Lee Jian Li Frank Mauseth Peter Morshuis Clive Reed Yasuhiro Tanaka Antonios Tzimas Kai Wu The following members of the individual balloting committ

38、ee voted on this recommended practice. Balloters may have voted for approval, disapproval, or abstention. Ettore Bartolucci William Byrd Jerome Castellon George Chen Namal Fernando John Fothergill Mingli Fu Paul Gaberson Randall Groves Werner Hoelzl Alexander Kraetge Michael Lauxman Jian Li Arturo M

39、aldonado Massimo Marzinotto Frank Mauseth Giovanni Mazzanti Peter Morshuis Clive Reed Yasuhiro Tanaka Antonios Tzimas Kai Wu When the IEEE-SA Standards Board approved this recommended practice on 23 March 2017, it had the following membership: Jean-Philippe Faure, Chair Vacant Position, Vice Chair J

40、ohn D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Gary Hoffman Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald C. Petersen Annette D. Reilly Robby Robson Do

41、rothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Y u Y uan *Member Emeritus7 Copyright 2017 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 1732-2017, IEEE Recommended Practice for Space Charge Measurements on High-V oltage Direct-Current Extr

42、uded Cables for Rated V oltages up to 550 kV . Recently many high-voltage direct-current (HVDC) cable systems with extruded insulation have been installed all over the world (Mazzanti and Marzinotto B13). Since extruded insulation for HVDC cables is strongly affected by trapped space charge, several

43、 space charge measurement methods have been developed since the mid-1980s. So far, space charge measurements have mostly been made using thin, small-size plaques and mini-cables. Much less effort has been devoted to cables of size and design comparable or equal to the full- size cables installed in

44、the field. On the other hand, space charge measurements on full-size cables are of great interest for practical cable systems, as such measurements enable actual service conditions of power cables to be evaluated. Inherent difficulties mainly related to thick insulation make measuring space charge o

45、n full-size cables difficult. However, since the 1990s, satisfactory space charge measurements on large HVDC extruded cables have been described in the literature. Furthermore, space charge measurements on full-size HVDC extruded cable loops have been, and are being, used worldwide in qualification

46、tests for HVDC extruded cable link projects. These measurements are based on project-dependent agreements between cable manufacturers and the customers, as there is no agreed standard procedure. Aiming to fill this gap, in 2015 a position paper prepared by the IEEE DEIS HVDC Cable Systems Technical

47、Committee was published (Mazzanti, et al. B12). The paper illustrates a protocol for the measurement of space charge on full-size HVDC extruded cables during load cycle qualification tests (either the long-duration voltage test of prequalification tests or the load cycle test of type tests). The pro

48、tocol incorporates experience gained in the above-mentioned space charge measurements for HVDC extruded cable system projects. This recommended practice aims at improving this protocol and establishing it as a reference IEEE best practice for the measurement of space charge on full-size HVDC extrude

49、d cables. At the time of writing of this document, the maximum rated voltage of HVDC extruded cable systems commissioned worldwide is 320 kV , but systems with rated voltage up to 525 kV are being qualified. Moreover, in 2012 CIGR issued the Technical Brochure 496 entitled “Recommendations for Testing DC Extruded Cable Systems for Power Transmission at a Rated V oltage up to 500 kV” (see Clause 2). Aiming at accounting for these recent and/or ongoing developments, an upper limit of 550 kV has been selected for the rated voltage of HVDC extruded cables to which the presen