IEEE 1901 2A-2015 en Low-Frequency (less than 500 kHz) Narrowband Power Line Communications for Smart Grid Applications Amendment 1《智能电网应用的低频率(低于500 kHz)窄带电力线通信.pdf

1、 IEEE Standard for Low-Frequency (less than 500 kHz) Narrowband Power Line Communications for Smart Grid Applications Amendment 1 Sponsored by the Power Line Communications Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Communications Society IEEE Std 1901.2a-2015 (Amendment

2、 to IEEE Std 1901.2-2013) IEEE Std 1901.2a-2015 (Amendment to IEEE Std 1901.2-2013) IEEE Standard for Low-Frequency (less than 500 kHz) Narrowband Power Line Communications for Smart Grid Applications Amendment 1 Sponsor Power Line Communications Standards Committee of the IEEE Communications Societ

3、y Approved 3 September 2015 IEEE-SA Standards Board Abstract: Changes to clarify how and when to encrypt header and payload information elements, update the interleaver design in order to eliminate some drawbacks in certain channels, a new PHY data primitive attribute so sub-band SNR data can be obt

4、ained from the PHY, modification to the frame counter size for security to make it consistent with IEEE Std 802.15.4e-2012, and adding a beacon attribute and change the zero crossing detector text are addressed in this amendment. Keywords: coexistence, G3-PLC, IEEE 1901.2a TM , IFFT OFDM, MAC, mediu

5、m access control, narrowband, PHY, physical layer, PLC, power line communications, PRIME. The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2015 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Publish

6、ed 2 October 2015. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating t

7、o: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and

8、services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standa

9、rds available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own in

10、dependent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

11、CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY

12、 WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE

13、 standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the

14、official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be c

15、onsidered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting informatio

16、n or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comment

17、s and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been address

18、ed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Bo

19、ard 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the

20、 standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and ap

21、proved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization

22、, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a lim

23、ited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923

24、 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded

25、at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect

26、. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are caut

27、ioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/

28、xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the follow

29、ing URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standar

30、d, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/stan

31、dards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimin

32、ation to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or

33、scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the valid

34、ity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Copyright 2015 IEEE. All rights reserved. vi Participants At the time this IEEE standard was completed, the 1901.2 Wor

35、king Group had the following membership: James LeClare, Chair Oleg Logvinov, Vice Chair James D. Allen, Editor Ed Eckert Gordon Gregg Cedric Lavenu Vern Olson Tarkesh Pande Daniel Popa Rob Ranck Kaveh Razazian Gary Stuebing The following members of the individual balloting committee voted on this st

36、andard. Balloters may have voted for approval, disapproval, or abstention. ABB, Inc. Broadcom Corporation Cisco Systems, Inc. Electric Power Research Institute, Inc. (EPRI) Itron Inc. Marvell Semiconductor, Inc. Microsemi Corporation Qingdao Eastsoft Communication Technology Co., Ltd. Renesas Electr

37、onics Corporation Sensus Southwest Jiaotong University STMicroelectronics John D. Kulick, Chair Jon Walter Rosdahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Ted Burse Stephen Dukes Jean-Philippe Faure J. Travis Griffith Gary Hoffman Michael Janez

38、ic Joseph L. Koepfinger* David J. Law Hung Ling Andrew Myles T. W. Olsen Glenn Parsons Ronald C. Petersen Annette D. Reilly Stephen J. Shellhammer Adrian P. Stephens Yatin Trivedi Phillip Winston Don Wright Yu Yuan Daidi Zhong *Member Emeritus vii Copyright 2015 IEEE. All rights reserved. Introducti

39、on This introduction is not part of IEEE Std 1901.2a-2015, IEEE Standard for Low-Frequency (less than 500 kHz) Narrowband Power Line Communications for Smart Grid ApplicationsAmendment 1. This standard is designed to enable low-frequency (500 kHz) narrowband power line communications (PLC) over indo

40、or and outdoor electrical wiring. The standard supports data rates of up to 500 kb/s and was developed as the result of a collaborative effort undertaken by a large cross section of the PLC industrys technical experts and stakeholders. It also contains a coexistence mechanism that was developed base

41、d on the requirements provided by the industry and with the input from the Smart Grid Interoperability Panel (SGIP) Priority Action Plan 15 (PAP15). This coexistence mechanism may be used by any PLC technology in this band without implementing the rest of the standard and will be maintained through

42、the IEEE-SA. The project was authorized 25 March 2010. The first draft was available in early January 2011. The first letter ballot was started in January 2012 and received final working group approval on 29 May 2013. Sponsor ballot was completed on 7 September 2013. The document was approved by the

43、 IEEE-SA Standards Board on 31 October 2013. The base standard amendment project was authorized 26 March 2015 and approved by the IEEE SA Standards Board on xx Month 2015. The scope of this amendment is as follows: Change to clarify how and when to encrypt header and payload information elements. Ch

44、ange to the interleaver design to eliminate some drawbacks in certain channels. Insert an attribute into a PHY data primitive so sub-band SNR data can be obtained from the PHY. Change to the frame counter size for security to make it consistent with IEEE Std 802.15.4e- 2012. Insert a beacon attribute Change the zero crossing detector text.