IEEE 1905 1A-2014 en A Convergent Digital Home Network for Heterogeneous Technologies Amendment 1 Support of New MAC PHYs and Enhancements《一种融合数字家庭网络的异构技术 修改件1 .pdf

1、 IEEE Standard for a Convergent Digital Home Network for Heterogeneous Technologies Amendment 1: Support of New MAC/PHYs and Enhancements Sponsored by the Power Line Communications Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Communications Society IEEE Std 1905.1a-2014 (Amendment t

2、o IEEE Std 1905.1-2013) IEEE Std 1905.1a-2014 (Amendment to IEEE Std 1905.1-2013) IEEE Standard for a Convergent Digital Home Network for Heterogeneous Technologies Amendment 1: Support of New MAC/PHYs and Enhancements Sponsor Power Line Communications Committee of the IEEE Communications Society Ap

3、proved 23 December 2014 IEEE-SA Standards Board Abstract: An abstraction layer for multiple home networking technologies that provides a common interface to widely deployed home networking technologies is defined in this standard: IEEE 1901 over power lines, IEEE 802.11 for wireless, Ethernet over t

4、wisted pair cable, and MoCA 1.1 over coax. Additional network technologies are supported by an extensible mechanism using an IEEE OUI and an XML-formatted document. Connectivity selection for transmission of packets arriving from any interface or application is supported by the 1905 abstraction laye

5、r. Modification to the underlying home networking technologies is not required by the 1905 abstraction layer, and hence it does not change the behavior or implementation of existing home networking technologies. The 1905 abstraction layer is between layers 2 and 3 and abstracts the individual detail

6、s of each interface, aggregates available bandwidth, and facilitates seamless integration. The 1905 abstraction layer also facilitates end-to-end quality of service (QoS) while simplifying the introduction of new devices to the network, establishing secure connections, extending network coverage, an

7、d facilitating advanced network management features including discovery, path selection, autoconfiguration, and QoS negotiation. Keywords: abstraction layer, access point (AP) autoconfiguration, data models, extensibility, fragmentation and reassembly, Generic Phy, IEEE 802.1 bridge discovery, IEEE

8、Std 802.11, IEEE Std 1901, IEEE Std 1905.1, L2, MoCA, pairwise master key, power management, push button, registration, security, topology discovery protocol, Wi-Fi, XML The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2015 by The Inst

9、itute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 February 2015. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or compl

10、eteness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no o

11、ther ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and

12、 comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. An

13、y person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT

14、SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONT

15、RACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development p

16、rocess involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-S

17、A Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting i

18、nformation on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of memb

19、ership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent

20、 a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to commen

21、ts or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on stand

22、ards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does n

23、ot imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws,

24、and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by refer

25、ence, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.

26、Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact C

27、opyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users o

28、f IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition

29、of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still

30、 of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendmen

31、ts, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, i

32、f any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may requ

33、ire use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Lett

34、er of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with

35、reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for whi

36、ch a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discrimina

37、tory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. vi Copyright 2015 IEEE. All rights r

38、eserved. Participants At the time this amendment was submitted to the IEEE-SA Standards Board for approval, the Convergent Digital Home Network Working Group had the following membership: Purva Rajkotia, Chair C. Scott Willy, Vice Chair Stephen Palm, Editor The following entities submitted technical

39、 contributions or commented on this amendment at various stages of project development. AT if the value is 1, then the EUI-48 field shall be present. 6 octets any EUI-48 value 1905.1 AL MAC address of a neighbor of the receiving device. 1 octet 0x00 : Tx link metrics only 0x01 : Rx link metrics only

40、 0x02 : Both Tx and Rx link metrics 0x030xFF: Reserved values. If any reserved value is received, ignore this TLV. The link metrics requested. IEEE Std 1905.1a-2014 IEEE Standard for a Convergent Digital Home Network for Heterogeneous Technologies Amendment 1: Support of New MAC/PHYs and Enhancement

41、s 11 Copyright 2015 IEEE. All rights reserved. 6.4.11 1905.1 transmitter link metric TLV Change the title and following rows in Table 6-18 in 6.4.11: Table 6-181905.1 transmitter link metrics Name Type Length Value range Description IEEE802.1BridgeFlag Boolean 1 octet 0x00: Indicates that the 1905.1

42、 link does not include an IEEE 802.1 bridge. 0x01: Indicates that the 1905.1 link includes one or more IEEE 802.1 bridges. 0x020xFF Reserved values. If any reserved value is received, ignore this TLV. Indicates whether or not the 1905.1 link includes one or more IEEE 802.1 bridges. phyRate Integer 1

43、6 2 octets Any integer value If the Media type of the link is IEEE 802.3, then IEEE 1901, MoCA 1.1, or Generic Phy (8 MSB bits value of Media type as defined in Table 6-12 is 0, 2, or 3, or 0xFF), then tThis value is the PHY rate estimated at the transmitter of the link expressed in Mb/s; otherwise,

44、 it is set to 0xFFFF. If any networking technology does not want to supply the PHY rate, it should set to 0xFFFF. 6.4.12 1905.1 receiver link metric TLV Change the title and following rows in Table 6-20 in 6.4.12: Table 6-201905.1 receiver link metrics Name Type Length Value range Description packet

45、ErrorsReceived Integer32 4 octets Any integer value Estimated number of lost packets during the measurement period. rssiRSSI Integer 8 1 octet Any integer value If the Media type of the link is IEEE 802.11 or Generic Phy (8 MSB value of Media type as defined in Table 6-12 is 1 or 0xFF), then this va

46、lue is the estimated RSSI in dB at the receive side of the Link expressed in dB; otherwise, it is set to 0xFF. If any networking technology does not want to supply RSSI, it should set to 0xFF. IEEE Std 1905.1a-2014 IEEE Standard for a Convergent Digital Home Network for Heterogeneous Technologies Am

47、endment 1: Support of New MAC/PHYs and Enhancements 12 Copyright 2015 IEEE. All rights reserved. 6.4.13 1905.1 link metric result code TLV Change the title and following row in Table 6-21 in 6.4.13: Table 6-211905.1 link metric result code TLV Field Length Value range Description tlvValue 1 octet 0x

48、00: Invalid neighbor 0x010xFF: Reserved values. If any reserved value is received, ignore this TLV. Result code for the link metric query message 6.4.14 SearchedRole TLV Change the following row in Table 6-22 in 6.4.14: Table 6-22SearchedRole TLV Field Length Value range Description tlvValue 1 octet

49、 0x00: Registrar 0x010xFF: Reserved values. If any reserved value is received, ignore this TLV. Type of role of the unconfigured interface requesting an autoconfiguration 6.4.15 AutoconfigFreqBand TLV Change the following row in Table 6-23 in 6.4.15: Table 6-23AutoconfigFreqBand TLV Field Length Value range Description tlvValue 1 octet 0x00: 802.11 2.4 GHz 0x01: 802.11 5 GHz 0x02: 802.11 60 GHz 0x030xFF: Reserved values. If any reserved value is received, ignore this TLV. Frequency band of the unconfigured interface requesting an autoconfiguration 6.4.16 Sup