IEEE 45 INT 1-2004 en Recommended Practice for Electric Installations on Shipboard《IEEE Std 45-2002用IEEE标准解释文件 船舶上电装置用IEEE推荐实施规程》.pdf

1、IEEE Std 45-2002_InterpretationIEEE Standards Interpretation for IEEE Std 45-2002IEEE Recommended Practice for Electric Installations on ShipboardCopyright 2004 by the Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue New York, New York 10016-5997 USA All Rights Reserved.This is

2、an interpretation of IEEE Std 45-2002. Interpretations are issued to explain and clarify the intent of a standard and are not intended to constitute an alteration to the original standard or to supply consulting information. Permission is hereby granted to download and print one copy of this documen

3、t. Individuals seeking permission to reproduce and/or distribute this document in its entirety or portions of this document must contact the IEEE Standard Department for the appropriate license. Use of the information contained in this document is at your own risk.IEEE Standards Department Copyright

4、s and Permissions 445 Hoes Lane, P. O. Box 1331 Piscataway, New Jersey 08855-1331, USAApril 9, 2004 Interpretation Number: #1 Clause Nos.: 31.15.1, and 3.16 Interpretation request #1IEEE Std 45-2002, Clause 31. Electric propulsion and maneuvering system, subclause 31.15.1 (Generators and motors), st

5、ates that “Generators and motors should successfully pass the following tests at the place of manufacture“ and continues to list a required battery of tests for propulsion motors. http:/standards.ieee.org/reading/ieee/interp/45-2002.html (1 of 4) 2009/01/06 7:05:18 PMIEEE Std 45-2002_InterpretationC

6、lause 13. Motors, subclause 13.16 Tests, states that “Prior to delivery, tests should be performed to ensure that the machine is in accordance with these recommendations and operates at its specified rating. When a machine is a duplicate of one already tested, only such check tests need be made as m

7、ay be necessary to demonstrate that the machine operates successfully.Does the allowance of type testing for motors, as laid out in subclause 13.16, also apply to propulsion motors covered by subclause 31.15.1, or should each propulsion motor undergo the tests listed in subclause 31.15.1?Interpretat

8、ion for IEEE Std IEEE Std 45-2002 No. Duplicate motor testing requirements as delineated in Clause 13 are not enough for propulsion motor. The propulsion motors are often custom designed due to the power range and propulsion service requirements. The propulsion motor cooling system testing, full loa

9、d testing, overload testing and propulsion duty cycle load testing require extensive preparation. Third party certification is necessary for the propulsion motor manufacture and testing. In general, the motor manufacturer prepares detail motor test procedures for all propulsion motors for customer a

10、nd regulatory body approval. The manufacturer usually follow the approved test procedure which usually witnessed and certified by authorized third party having jurisdiction in this field, such as ABS, Lloyds, DNV, etc. If certain tests are not to be performed due to cost consideration, the certifyin

11、g authority may consider waiver of certain requirements in writing. As an example, the ABS class ship must follow the ABS requirement for manufacture and testing the propulsion motors in accordance with ABS certification requirement. The propulsion motor procurement cost estimate should include manu

12、facture and testing. References a, b, and c are the IEEE Std 45 pertinent clauses provided for information in support of the response. References: a. IEEE-45-2002- Clause 31-Electric Propulsion 31.15 Tests 31.15.1 Generators and motors Generators and motors should successfully pass the following tes

13、ts at the place of manufacture. The following tests should be conducted in accordance with IEC60034 or IEEE http:/standards.ieee.org/reading/ieee/interp/45-2002.html (2 of 4) 2009/01/06 7:05:18 PMIEEE Std 45-2002_InterpretationStd 112-1996, IEEE Std 115-1995, or ANSI/NEMA MG 1-1998, as applicable: a

14、) Temperature rise under rated load or rated current conditions b) Dielectric strength of insulation c) Overload capacity, as specified b. IEEE-45-1998 Clause 36-Electric Propulsion 36.18 Tests-generators and motors Generators and motors should successfully pass the following tests at the place of m

15、anufacture. The following tests should be conducted in accordance with IEEE Std 112 1996, IEEE Std 115-1995, or ANSI/NEMA MG 1-1993, as applicable: a) Temperature rise under full-load conditions b) Dielectric strength of insulation c) Overload capacity, as specified d) Cold resistance of all circuit

16、s e) Electrical balance f) Mechanical balance c. IEEE-45-2002 Clause 13-Motor -13.16 Tests Prior to delivery, tests should be performed to ensure that the machine is in accordance with these recommendations and operates at its specified rating. When a machine is a duplicate of one already tested, on

17、ly such check tests need be made as may be necessary to demonstrate that the machine operates successfully. Spare parts should be given a regular insulation resistance test, but need not be given any running test. Tests should be conducted in accordance with the following: a) For single-phase motors

18、 ANSI/NEMA MG-1-1998 b) For polyphase induction motors, IEEE Std 112-1996 c) For synchronous motors, IEEE Std 115-1995 d) For dc motors, ANSI/NEMA MG-1-1998 e) For IEC motors, IEC 60034 f) For chemical duty motors up to and including 373 kW (500 HP), IEEE Std 841-2001 g) For chemical duty motors ab

19、ove 373kW (500 HP), API Std 541 The tests that should be performed are -.Temperature-rise -Insulation resistance -High potential -Overload -Commutation test http:/standards.ieee.org/reading/ieee/interp/45-2002.html (3 of 4) 2009/01/06 7:05:18 PMIEEE Std 45-2002_InterpretationCopyright 2004 IEEE. All rights reserved.Back to Available IEEE Standards Interpretations Online Copyright IEEE-SA Contact IEEE-SA For questions or comments, please contact the IEEE-SA Webmaster. http:/standards.ieee.org/reading/ieee/interp/45-2002.html (4 of 4) 2009/01/06 7:05:18 PM