IEEE C37 13 1-2016 en Definite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage (600 V AC and Below) Power Circuit Breaker Switchgear《附金属壳的低压(600.pdf

1、IEEE Standard for Definite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage (600 V AC and Below) Power Circuit Breaker SwitchgearIEEE Std C37.13.1-2016(Revision of IEEE Std C37.13.1-2006)IEEE Power and Energy SocietySponsored by the Switchgear CommitteeIEEE3 Park AvenueNew York, NY 10

2、016-5997USAIEEE Std C37.13.1-2016(Revision of IEEE Std C37.13.1-2006)IEEE Standard for Definite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage (600 V AC and Below) Power Circuit Breaker SwitchgearSponsor Switchgear Committee of the IEEE Power and Energy SocietyApproved 30 June 2016I

3、EEE-SA Standards BoardAbstract: Defi nite-purpose switching devices for use in metal-enclosed low-voltage power circuit breaker switchgear are covered in this standard. The switching devices are fused, drawout type, three-pole construction, with one or more rated maximum ac voltages of 600 V, 508 V,

4、 and 254 V for application on systems having nominal ac voltages of 600 V, 480 V, and 240 V. The switching devices are power operated with integral or separately mounted overcurrent protective devices. Service conditions, ratings, functional components, temperature limitations and classifi cations o

5、f insulating materials, insulation (dielectric) withstand voltage requirements, test procedures, and application are addressed in this standard. The switching devices are normally used in applications that require frequency of operation greater than normal operations expected of low-voltage power ci

6、rcuit breakers.Keywords: defi nite-purpose switching device, IEEE C37.13.1, low-voltage ac power circuit breakerThe Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2017 by the Institute of Electrical and Electronics Engineers, Inc.All right

7、s reserved. Published 15 February 2017. Printed in the United States of America.IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all c

8、onditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.”Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provi

9、de other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard.In publishing and

10、 making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon

11、 his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropri-ate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard.IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECI

12、AL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCURE-MENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CON-TRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHER

13、WISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.4Copyright 2017 IEEE. All rights reserved.TranslationsThe IEEE consensus development process involves the re

14、view of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard.Official statementsA statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operat

15、ions Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE stand

16、ards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE.Comments on standardsComments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IE

17、EE. However, IEEE does not provide consulting information or advice pertain-ing to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned

18、 interests, it is important that any responses to comments and questions also receive the concur-rence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordi-nating Committees are not able to provide an instant response to comments or questions except

19、in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group.Comments on standards should be submitted

20、 to the following address:Secretary, IEEE-SA Standards Board445 Hoes LanePiscataway, NJ 08854 USALaws and regulationsUsers of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any ap

21、plicable regulatory require-ments. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not

22、be construed as doing so.CopyrightsIEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations,

23、 and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adop-tion by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5Copyright 2017 IEEE. All righ

24、ts reserved.PhotocopiesSubject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, pleas

25、e contact Copyright Clearance Center, Customer Ser-vice, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center.Updating of IEEE Standards docume

26、ntsUsers of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corri-genda, or errata. An official IEEE document at any point in time consists of the curre

27、nt edition of the document together with any amendments, corrigenda, or errata then in effect.Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, alth

28、ough still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard.In order to determine whether a given document is the current edition and whether it has been amended through the issuance of

29、 amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ieeexplore.ieee.org/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org.ErrataErrata, if any, for all

30、 IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically.PatentsAttention is called to the possibility that implementation of this standard may require use of subje

31、ct matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance,

32、 then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms

33、 and conditions that are demonstrably free of any unfair discrim-ination to applicants desiring to obtain such licenses.Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not re-sponsible for identifying Essential Patent Claims for which a license ma

34、y be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of

35、this standard are expressly advised that determination of the valid-ity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6Copyright 2017 IEEE. All rights reserved.Participa

36、ntsAt the time this IEEE standard was completed, the IEEE standard for Defi nite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear Working Group had the following membership:Dan Hrncir, ChairDean Sigmon, Vice ChairClint CarneDavid DunneDouglas J. Edward

37、sMike FlackKeith FlowersLou GrahorThomas HawkinsJeffrey HidakaArt JurMike LafondAllan MorseDarryl MoserRichard RohrPaul SullivanRob WarrenThe following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention.Paul Barnhar

38、tWilliam BloetheTed BurseWilliam ByrdEldridge ByronPaul CardinalGlenn DavisStephen DeRocheGary DonnerDavid DunneDouglas J. EdwardsRonald EscoKeith FlowersMietek GlinkowskiEdwin GoodwinLou GrahorRandall GrovesThomas HawkinsJeffrey HelzerJeffrey HidakaDan HrncirDavid JacksonRichard JacksonJohn KayYuri

39、 KhersonskyBoris KoganJim KulchiskyEd LarsenFrank MayleWilliam McBrideCharles MorseDarryl MoserJerry MurphyDennis NeitzelMichael NewmanNick S. A. NikjooT. W. OlsenShawn PattersonChristopher PetrolaIulian Profi rMichael RobertsTimothy RobirdsThomas RozekBartien SayogoMichael SigmonJeremy SmithJerry S

40、mithPaul SullivanDonald SwingDavid TepenJohn VergisJohn WangKenneth WhiteIain WrightLarry YonceJian YuWhen the IEEE-SA Standards Board approved this standard on 30 June 2016, it had the following membership:Jean-Philippe Faure, ChairTed Burse, Vice ChairJohn D. Kulick, Past ChairKonstantinos Karacha

41、lios, SecretaryChuck AdamsMasayuki AriyoshiStephen DukesJianbin FanJ. Travis Griffi thGary HoffmanRonald W. HotchkissMichael JanezicJoseph L. Koepfi nger*Hung LingKevin LuAnnette D. ReillyGary RobinsonMehmet UlemaYingli WenHoward WolfmanDon WrightYu YuanDaidi Zhong*Member Emeritus7Copyright 2017 IEE

42、E. All rights reserved.IntroductionThis introduction is not part of IEEE Std C37.13.1-2016, IEEE Standard for Definite-Purpose Switching Devices for Use in Metal-Enclosed Low-Voltage (600 V AC and Below) Power Circuit Breaker Switchgear.IEEE Std C37.13.1-2006 was written specifically to provide requ

43、irements for switching devices other than low-voltage power circuit breakers installed in low-voltage power circuit breaker switchgear. Definite-pur-pose switching (DPS) device in this standard is defined as a switching device used on a frame in a manner similar to a power circuit breaker and instal

44、led in low-voltage power circuit breaker switchgear.This standard was developed because several incidents in the industry indicated that switching devices (i.e., switching devices utilizing contactors) were being improperly designed, applied, and installed in low-voltage power circuit breaker switch

45、gear.This standard is limited to DPS devices using contactors protected by current-limiting fuses. Additional types of DPS devices may be addressed in future editions of this standard.This standard has been revised to reflect needed technical changes that have been suggested since the original editi

46、on was published in 2006. Major editorial and technical changes have been incorporated. The more signif-icant changes include the following: IEEE Std C37.13.1a-2010 has been incorporated into this revision. Equipment voltage rating was added to the title of the standard. For clarification purposes,

47、LV” (low voltage) was added to all instances of the acronym “DPS” (defi-nite-purpose switching). References to IEEE Std C37.16 have been replaced by references to IEEE Std C37.13. Dates (i.e., year of approval) were removed from all referenced standards.8Copyright 2017 IEEE. All rights reserved.Con

48、tents1. Overview . 91.1 Scope 91.2 Purpose . 92. Normative references 93. Definitions . 104. Normal service condition 105. Ratings 115.1 General . 115.2 Rated maximum voltage . 125.3 Rated power frequency . 125.4 Rated continuous current 125.5 Rated short-circuit current 125.6 Rated control voltage

49、126. Functional components . 136.1 General . 136.2 Nameplate(s) 136.3 Contact position indicator . 146.4 Stored-energy indicator (for stored-energy type-closing mechanisms only) 146.5 LV-DPS device retention and locking . 146.6 Fuse accessibility 146.7 Interlocks 146.8 Secondary disconnect devices 156.9 Removable element interchangeability 157. Temperature limitations and classification of insulting materials 157.1 Temperature limits 157.2 Limits of temperature rise . 158. Tests 168.1 General . 168.2 Design (type) test 168.3 Production (routine) tests . 198.4 Field