IEEE C37 41-2016 en Design Tests for High-Voltage ( 1000 V) Fuses and Accessories《高电压（ 1000 V）熔断器和附件的设计试验》.pdf

1、 IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Sponsored by the Switchgear Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std C37.41-2016 (Revision of IEEE Std C37.41-2008) IEEE Std C37.41-2016 (Revision of IEEE Std C37.41-200

2、8) IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Sponsor Switchgear Committee of the IEEE Power and Energy Society Approved 22 September 2016 IEEE-SA Standards Board IEEE Std C37.41-2016 IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Abstract:

3、 Required procedures for performing design tests for high-voltage fuses, as well as for fuse disconnecting switches, are specified. These design tests, as appropriate to a particular device, include the following test types: dielectric, interrupting, radio-influence, temperature-rise, time-current,

4、manual-operation, liquid-tightness, thermal-cycle, bolt-torque, withstand tests for motor circuit fuses, expulsion fuses using polymeric insulators, load-break, and short-time current. Keywords: fuse accessories, fuse design tests, fuse disconnecting switches, fuse-enclosure package (FEP), high-volt

5、age fuses, IEEE 37.41 The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 9 December 2016. Printed in the United States of America. IEEE is

6、 a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are su

7、pplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, th

8、e viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or

9、other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given

10、circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT O

11、F SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD,

12、 EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. IEEE Std C37.41-2016 IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Translations The IEEE consensus development process involves the review of documents in English on

13、ly. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be cons

14、idered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that

15、 his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not

16、provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important

17、that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matte

18、r has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Se

19、cretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requ

20、irements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so

21、Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self

22、-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. IEEE Std C37.41-2016 IEEE Standard Design Tests for Hi

23、gh-Voltage (1000 V) Fuses and Accessories Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for p

24、ayment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Up

25、dating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any poin

26、t in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to

27、conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has bee

28、n amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ieeexplore.ieee.org/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.

29、org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of t

30、his standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance

31、 via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under re

32、asonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential

33、Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasona

34、ble or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association IEEE Std C37.41-

35、2016 IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Participants At the time this IEEE standard was completed, the Revision of Fuse Standards Working Group had the following membership: John G. Leach, Chair Glenn R. Borchardt, Secretary Chris Ambrose Chris Borck Samuel Ch

36、ang Sterlin Cochran Jonathan Deverick Rodolfo Elizondo Doug Fitchett David Frisch Dan Gardner Gary Haynes Blake Henard Frank C. Lambert Chris Lettow Bradley Lewis Eric Li Jim R. Marek Sean Moody R. Neville Parry Timothy Royster Jon Spencer Mark W. Stavnes Tom Stefanski Dustin Sullivan William Walter

37、 Randy Ward James Wenzel Charles Worthington Alan Yerges The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Chris Ambrose Charles Ball Paul Barnhart Craig Befus Robert Behl Jean-Marc Biasse Gustavo Br

38、unello William Byrd Thomas Callsen Paul Cardinal Suresh Channarasappa Frank Decesaro Gary Donner Edgar Dullni Rodolfo Elizondo Marcel Fortin Edwin Goodwin Randall Groves Gary Haynes Jeffrey Helzer Richard Jackson John Kay Yuri Khersonsky Boris Kogan Jim Kulchisky Saumen Kundu Chung-Yiu Lam Frank C.

39、Lambert John G. Leach Bradley Lewis Albert Livshitz William McBride Sean Moody Daniel Mulkey Michael Newman T. W. Olsen Lorraine Padden Bansi Patel Iulian Profir Michael Roberts Timothy Robirds Timothy Royster Thomas Rozek Bartien Sayogo Jeremy Smith Jerry Smith Mark Stavnes Tom Stefanski David Tepe

40、n James Van De Ligt John Vergis William Walter Terry Woodyard Charles Worthington Alan Yerges When the IEEE-SA Standards Board approved this standard on 22 September 2016, it had the following membership: Jean-Philippe Faure, Chair Ted Burse, Vice Chair John D. Kulick, Past Chair Konstantinos Karach

41、alios, Secretary Chuck Adams Masayuki Ariyoshi Stephen Dukes Jianbin Fan J. Travis Griffith Gary Hoffman Ronald W. Hotchkiss Michael Janezic Joseph L. Koepfinger* Hung Ling Kevin Lu Annette D. Reilly Gary Robinson Mehmet Ulema Yingli Wen Howard Wolfman Don Wright Yu Yuan Daidi Zhong *Member Emeritus

42、 Copyright 2016 IEEE. All rights reserved. 6 IEEE Std C37.41-2016 IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories Introduction This introduction is not part of IEEE Std C37.41-2016, IEEE Standard Design Tests for High-Voltage ( 1000 V) Fuses and Accessories. IEEE Std C37.4

43、1-2016 is a revision of IEEE Std C37.41-2008, done in order to bring it up to date and into agreement with current requirements for high-voltage fuses and switches. The structure of the document has changed significantly. An attempt has been made to better separate testing requirements between expul

44、sion fuses and current-limiting fuses. Fuse types that have restricted application, in terms of performance requirements or geographical applicability, have been separated from those that have essentially universal applicability, and placed in a normative Annex. Test requirements for distribution cl

45、ass high-voltage ( 1000 V) enclosed single-pole air switches have been moved to IEEE Std C37.45. Several changes to the expulsion and current-limiting fuse-testing requirements have been made to align more closely with the latest International Electrotechnical Commission (IEC) test requirements. The

46、 Revision of Fuse Standards Working Group of the IEEE Subcommittee on High-Voltage Fuses prepared the standard. Liaison was maintained with the IEC during the development of the revisions in order to incorporate the latest activities at the time of publication. This standard is one of a series of co

47、mplementary standards covering various types of high-voltage fuses and switches and covers basic testing requirements, while IEEE Std C37.42-2016 contains the specification requirements for those devices. IEEE Std C37.45-2016 contains all of the testing requirements and specifications for high-volta

48、ge distribution class enclosed single-pole air switches. IEEE Std C37.41-2016 and IEEE Std C37.42-2016 together, and IEEE Std C37.45-2016 alone, provide all of the testing requirements for a device. In addition, IEEE Std C37.48-2005 provides application, operation, and maintenance guidance for all t

49、he devices, and it is supplemented by IEEE Std C37.48.1-2011 which is an application, operation, and coordination guide for current-limiting fuses. At the time this standard was approved, this series comprised the following standards: IEEE Std C37.41-2016, IEEE Standard Design Tests for High-Voltage (1000 V) Fuses and Accessories. IEEE Std C37.42-2016, IEEE Standard Specifications for High-Voltage (1000 V) Fuses and Accessories. IEEE Std C37.45-2016,IEEE Standard Design Tests and Specifications for High-Voltage (1000 V) Distribution Class Enclosed Single-Pole Air Switche