IEEE C57 13 3-2014 en Guide for Grounding of Instrument Transformer Secondary Circuits and Cases《仪表用变压器次级线圈电路外壳接地指南》.pdf

1、 IEEE Guide for Grounding of Instrument Transformer Secondary Circuits and Cases Sponsored by the Power System Relaying Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std C57.13.3-2014 (Revision of IEEE Std C57.13.3-2005) IEEE Std C57.13.3-2014 (Revision

2、of IEEE Std C57.13.3-2005) IEEE Guide for Grounding of Instrument Transformer Secondary Circuits and Cases Sponsor Power System Relaying Committee of the IEEE Power and Energy Society Approved 10 December 2014 IEEE-SA Standards Board Abstract: General and specific recommendations for grounding curre

3、nt and voltage transformer secondary circuits and cases of connected equipment are covered in this guide. Although most diagrams included in this guide show relaying applications, the recommended practices apply equally to metering and other areas where instrument transformers are used. Grounding pr

4、actices presently used, and practices that were not previously reported, are included in this guide. Specifically, a review of other than North American grounding practices is included. Keywords: Capacitive voltage transformer, combined metering unit, current transformer, grounding of cases of instr

5、ument transformers, grounding secondary circuits of instrument transformers, IEEE C57.13.3, instrument transformer, linear coupler, low energy transducer, resistive voltage transformer, voltage transformer. The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016

6、5997, USA Copyright 2015 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 23 January 2015. Printed in the United States of America. IEEE and NESC are registered trademarks in the U.S. Patent fitness for a particular purpose; non-infringement; and quality

7、 accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEE

8、E standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about thr

9、ough developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed

10、 by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropria

11、teness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AN

12、D ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.

13、Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that i

14、s not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or ed

15、ucational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome

16、from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate suppor

17、ting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not

18、able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the r

19、elevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the pro

20、visions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action tha

21、t is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and p

22、rivate uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not wai

23、ve any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange fo

24、r payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center.

25、 Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any p

26、oint in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable

27、to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has

28、been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website

29、at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility

30、that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed

31、a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without

32、compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible fo

33、r identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensin

34、g agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Asso

35、ciation. Participants At the time this IEEE guide was completed, the PC57.13.3 Working Group for Grounding of Instrument Transformer Secondary Circuits and Cases had the following membership: Brian P. Mugalian, Chair Bruce A. Magruder, Vice Chair George Bartok Dean Bender Robert Beresh Lee Bigham Ze

36、eky Bukhala Stephen Conrad Dominick Fontana Gerald Johnson Gary Kobet Jeff Long Dhirenkumar Patel Bruce Pickett Jeff Pond Mohindar Sachdev Donald Sevcik Mike Stojak Joe Uchiyama Johan Vandenberg Delbert D. Weers Ray Young Richard Young The following members of the individual balloting committee vote

37、d on this guide. Balloters may have voted for approval, disapproval, or abstention. William Ackerman Ali Al Awazi Mihaela Albu Steven Alexanderson Jay Anderson Jeffrey Barsch George Bartok Michael Basler Philip Beaumont Kenneth Behrendt Robert Beresh Martin Best Steven Bezner Wallace Binder Gustavo

38、Brunello Zeeky Bukhala Paul Cardinal Stephen Conrad Randall Crellin Ratan Das Gary Donner Randall Dotson Sourav Dutta Doaa Galal Frank Gerleve Jeffrey Gilbert Jalal Gohari Stephen Grier Randall Groves Ajit Gwal Scott Hietpas Jerry Hohn David Horvath Gerald Johnson Laszlo Kadar John Kay Gael Kennedy

39、Yuri Khersonsky James Kinney Gary Kobet Joseph L. Koepfinger Boris Kogan Jim Kulchisky Saumen Kundu Chung-Yiu Lam Michael Lauxman Greg Luri Bruce Mackie Bruce A. Magruder John Miller Venkatesh Minisandram Brian P. Mugalian Randolph Mullikin Jerry Murphy Arthur Neubauer Michael Newman Joe Nims Gary N

40、issen James OBrien Gearold O. H. Eidhin Ted Olsen Lorraine Padden Mirko Palazzo Dhirenkumar Patel Bruce Pickett Samala Santosh Reddy Michael Roberts Charles Rogers Zoltan Roman Jesse Rorabaugh Mohindar Sachdev Steven Sano Bartien Sayogo Robert Seitz Donald Sevcik Veselin Skendzic James Smith Jeremy

41、Smith Jerry Smith Gary Smullin Gary Stoedter Michael Thompson Robert Thornton-Jones Demetrios Tziouvaras Joe Uchiyama John Vergis Ilia Voloh John Wang Delbert D. Weers Kenneth White Philip Winston Ray Young Richard Young Jian Yu Copyright 2015 IEEE. All rights reserved. viWhen the IEEE-SA Standards

42、Board approved this guide on 10 December 2014, it had the following membership: John Kulick, Chair Jon Walter Rosdahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Peter Balma Farooq Bari Ted Burse Clint Chaplin Stephen Dukes Jean-Philippe Faure Gary Hoffman Michael J

43、anezic Jeffrey Katz Joseph L. Koepfinger* David J. Law Hung Ling Oleg Logvinov T. W. Olsen Glenn Parsons Ron Petersen Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Don Wright Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard De

44、Blasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE-SA Content Production and Management Erin Spiewak IEEE-SA Technical Program Operations Copyright 2015 IEEE. All rights reserved. viiIntroduction This introduction is not part of IEEE Std C57.13.3-2014, IEEE Guide fo

45、r Grounding of Instrument Transformer Secondary Circuits and Cases. The primary emphases of this guide are personnel safety and proper performance of relays at the electric power system frequencies. The grounding and shielding of cables and other grounding considerations are not addressed. However,

46、references dealing with these and related subjects are included in the bibliography (see Annex D). Historically, it has been a common practice in the U.S. to connect the secondary circuits of current transformers (CTs) and voltage transformers (VTs) to the station ground. The present preferred pract

47、ice is to locate a ground on the instrument transformer secondary circuit, along with suitable ground isolation test facilities, at the first point of application (switchboard or relay panel). The circuit ground isolation facilities make it convenient to test the integrity of the insulation from gro

48、und. Previous publications have made significant contributions toward making the grounding practices more consistent in some areas. This guide includes the contributions that are generally practiced today, makes revisions where present experience and practice show them to be desirable, and suggests

49、grounding techniques in new areas of interest. Diagrams are included to illustrate the grounding techniques. This guide contains general and specific recommendations for grounding CT and VT secondary circuits and cases of connected equipment. The recommended practices apply to all transformers of this type, including capacitive VTs and linear couplers, irrespective of the voltage of the primary circuit or whether the primary windings are connected to the power circuits or are connected to the secondary circuits of other transformers, such as auxiliary CTs or VTs. Most diagrams