ISO 10145-1-2016 End mills with brazed helical hardmetal tips - Part 1 Dimensions of end mills with parallel shank《焊有硬质合金螺旋刀头的端铣刀 第1部分 直柄端铣刀尺寸》.pdf

1、 ISO 2016 End mills with brazed helical hardmetal tips Part 1: Dimensions of end mills with parallel shank Fraises cylindriques deux tailles plaquettes hlicodales en mtaux- durs, brases Partie 1: Dimensions des fraises queue cylindrique INTERNATIONAL STANDARD ISO 10145-1 Second edition 2016-03-01 Re

2、ference number ISO 10145-1:2016(E) ISO 10145-1:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, elec

3、tronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Ver

4、nier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 10145-1:2016(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 Annex A (informative) Relationship between designations in this part of ISO 10145 and ISO 13399 . 3 ISO 2016 All righ

5、ts reserved iii Contents Page ISO 10145-1:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

6、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa

7、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different

8、types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not

9、 be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is inf

10、ormation given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see

11、 the following URL: Foreword - Supplementary information. The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items. This second edition cancels and replaces the first edition (ISO 10145-1:1993), which constitutes a mino

12、r revision. ISO 10145 consists of the following parts, under the general title End mills with brazed helical hardmetal tips: Part 1: Dimensions of end mills with parallel shank Part 2: Dimensions of end mills with 7/24 taper shankiv ISO 2016 All rights reserved INTERNATIONAL ST ANDARD ISO 10145-1:20

13、16(E) End mills with brazed helical hardmetal tips Part 1: Dimensions of end mills with parallel shank 1 Scope This part of ISO 10145 specifies the general dimensions of end mills with brazed helical hardmetal tips, with parallel shank. The following two types of end mills with parallel shank are sp

14、ecified: end mills with plain parallel shank; end mills with flatted parallel shank. This part of ISO 10145 applies to right-hand and left-hand end mills, irrespective of the helix angle and number of flutes. 2 Normative references The following documents, in whole or in part, are normatively refere

15、nced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 33381, Parallel shanks for milling cutters Part 1: Dimensions of plain

16、parallel shanks ISO 33382, Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks 3 Dimensions The dimensions for end mills as shown in Figure 1 are specified in Table 1. l L d d l L d d Type 1: With plain parallel shank, in accordance with ISO 33381

17、 Type 2: With flatted parallel shank, in accordance with ISO 33382 Figure 1 Dimensions for end mills ISO 2016 All rights reserved 1 ISO 10145-1:2016(E) Table 1 Dimensions for end mills Dimensions in millimetres d l d 1 L k12 nom. tol. 12 20 12 75 25 80 16 25 16 88 32 95 20 32 20 97 40 105 25 40 25 1

18、11 50 121 32 40 32 120 50 130 40 50 40 140 63 1532 ISO 2016 All rights reserved ISO 10145-1:2016(E) Annex A (informative) Relationship between designations in this part of ISO 10145 and ISO 13399 For relationship between designations in this part of ISO 10145 and preferred symbols according to ISO 1

19、3399, see Table A.1. Table A.1 Relationship between designations in this part of ISO 10145 and ISO 13399 series Symbol in ISO 101451 Reference in ISO 101451 Property name in ISO 13399 Symbol in ISO 13399 Reference in ISO 13399 d Figure 1 and Table 1 cutting diameter DC ISO/TS 13399-3 71CE7A96D9F7D d

20、 1 Figure 1 and Table 1 connection diameter machine side DCONMS ISO/TS 13399-3 71EBDBF5060E6 l Figure 1 and Table 1 depth of cut maximum APMX ISO/TS 13399-3 71D07576C0558 L Figure 1 and Table 1 overall length OAL ISO/TS 13399-3 71D078EB7C086 ISO 2016 All rights reserved 3 ISO 10145-1:2016(E) ISO 2016 All rights reserved ICS 25.100.20 Price based on 3 pages