ISO 1341-1976 Straight bevel gears Information to be given to the manufacturer by the purchaser in order to obtain the gear required《锥齿轮 图样上应注明的买方要求的尺寸数据》.pdf

1、INTERNATIONAL STANDARD 1341 Straight bevel gears - Information to be given to the manufacturer by the purchaser in order to obtain the gear required Ertgrenages coniques - Indications i fournir au tailleur dengrenages par le client pour obtenir la denture dksirtie First edition - 1976-08-01 iii UDC

2、621.833.2 : 658.74 Ref. No. IS0 1341-1976 (E) co - 6 i Descriptors : gears, bevel gears, engineering drawings, specifications. 0 5!2 Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permi

3、tted without license from IHS-,-,-FOREWORD IS0 (the International Organization for Standardization) is a worldwide federation of national standards institutes (IS0 Member Eodies). The work of developing International Standards is carried out through IS0 Technical Committees. Every Member Body intere

4、sted in a subject for which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees are

5、circulated to the Member Bodies for approval before their acceptance as International Standards by the IS0 Council. Prior to 1972, the results of the work of the Technical Committees were published as IS0 Recommendations; these documents are now in the process of being trans- formed into Internation

6、al Standards. As part of this process, Technical Committee ISOnC 60 has reviewed IS0 Recommendation R 1341 and found it technically suitable for transformation. International Standard IS0 1341 therefore replaces IS0 Recommendation R 1341-1971 to which it is technicallv identical. IS0 Recommendation

7、R 1341 was approved by the Member Bodies of the following countries : Australia Austria Belgium Chile Czechoslovakia Egypt, Arab Rep. of Finland France Germany Greece India Israel Italy Japan Korea, Rep. of Netherlands New Zealand Paraguay Poland South Africa, Rep. of Spain Sweden Switzerland Thaila

8、nd Turkey United Kingdom U.S.S.R. Yugoslavia The Member Body of the following country expressed disapproval of the Recommendation on technical grounds : Hungary The Member Body of the following country disapproved the transformation of 60/R 1341 into an International Standard : Germany 0 Intomhod Or

9、gmization for Standardization, 1976 l Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD IS0 1341-1976 (E) Straight bevel gears

10、 - Information to be given to the manufacturer by the purchaser in order to obtain the gear required 1 SCOPE AND FIELD OF APPLICATION This International Standard specifies the information which should be stated on all straight bevel gear drawings. For each particular case they should be completed by

11、 such information as may be necessary or useful. 2 REFERENCES I SO1 R 468, Surface roughness. IS0 677, Basic rack of straight bevel gears for general engineering and heavy engineering. IS0 1302, Technical drawings - Method of indicating surface texture on drawings. IS0 2203, Technical drawings - Con

12、ventional represen- ta tion of gears. IS0 . . ., Conical gears - IS0 system of accuracy.) 3 GENERAL DIMENSIONS AND CHARACTERISTICS TO BE INDICATED ON THE DRAWING - Tip diameter and tolerance - Facewidth - Tip angle - Angle of the back cone (and, if applicable, inner cone) - Bore diameter and toleran

13、ce (or diameter and tolerance for the part of the shaft used for the setting on the cutting machine) - Locating face(s) - Distance to the locating face : a : from the pitch cone apex (locating distance) and tolerance b : from the pitch circle c : from the tip circle of the tip cone (tip distance) an

14、d tolerance d : from the tip circle of the inner cone e : from the inner face - Surface finish of the tooth flank surfaces and, if applicable, of the root surface and of the fillets2) Locating face J 1) In preparation. 2) Specifications concerning surface texture and the symbols used should be in ac

15、cordance with lSO/R 468 and IS0 1302. Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 1341-1976 (E) 4 INFORMATION TO BE GIVEN IN A TABLE The following information sho

16、uld preferably be given in the upper right-hand corner of the drawing : - Module of diametral pitch - Number of teeth (for a sector : total number of teeth of the gear from which the sector is taken) - Basic rack (give the number of the corresponding national standard or the pressure angle of 20. If

17、 the basic rack differs from the standard rack, its character- istics should be specified, preferably by a figure) - Reference diameter - Reference cone angle - Cone distance - Addendum modification coefficient (to be expressed in unit module) - Root angle or dedendum angle - Tooth thickness : basic

18、 value and upper and lower deviations - All useful information on tolerances (see ISO. . .) - Shaft angle of the gear pair and tolerance - Number of teeth and drawing number of the mating gear. NOTE - The features outlined in clauses 3 and 4 are those which are considered essential. Any other useful

19、 information should be given to the gear manufacturer for the manufacture and inspection of the teeth as required by the particular form and characteristics of the gear. In particular : a) the necessity of ensuring firm location of the body of the gaar on the cutting machine will require that the su

20、pport and clamping faces (which should be perpendicular to the axis) and their permissible axial run-out should ba indicated; b) for shafted pinions and wheels the bores of which will not be used as reference for centring. it is necessary to specify the maximum radial run-out of the surface which se

21、rves as datum for checking the centring before commencement of cutting. 5 EXAMPLE I a H 8 Dimensions in millimetres “O-0.025 0 18-0.025_ yc Bj : locating face . Charecteristics of the teeth Module 5 Number of teeth 16 Basic rack IS0 677 - 20” Reference diameter 80 mm Reference cone angle 18,08” or 1

22、8”448” Cone distance 128.87 mm I Addendum modification coefficient 0.42 I Root angle 16.38” or 16”2248” Tooth thickness : Constant chord/Addendum I Quality classl) I I I Shaft angle 90” I Mating gear z=49 drawing No. 54321 I 2) 1 1) According to IS0 . . . or to a corresponding national standard. 2) Complementary information which may be necessary or useful. 2 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-