ISO 14930-2012 Leather - Leather for dress gloves - Specification《皮革 礼服手套皮革 规范》.pdf

1、 Reference number ISO 14930:2012(E) ISO 2012INTERNATIONAL STANDARD ISO 14930 First edition 2012-02-01 Leather Leather for dress gloves Specification Cuir Cuir pour gants de crmonie Spcifications ISO 14930:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified,

2、no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case pos

3、tale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2012 All rights reservedISO 14930:2012(E) ISO 2012 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide fe

4、deration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that com

5、mittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accord

6、ance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard require

7、s approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14930 was prepared by Technical

8、Committee ISO/TC 120, Leather, Subcommittee SC 2, Tanned leather. INTERNATIONAL STANDARD ISO 14930:2012(E) ISO 2012 All rights reserved 1Leather Leather for dress gloves Specification 1 Scope This International Standard specifies the requirements, sampling and methods of testing for chrome and chrom

9、e-alum tanned leather used for the manufacture of dress gloves. This International Standard does not apply to chamois and alum tanned (tawed) leather or to leather for safety or sports gloves. 2 Normative references The following referenced documents are indispensable for the application of this doc

10、ument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 105-B02, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test ISO 2418, L

11、eather Chemical, physical and mechanical and fastness tests Sampling location ISO 2419, Leather Physical and mechanical tests Sample preparation and conditioning ISO 2588, Leather Sampling Number of items for a gross sample ISO 3376, Leather Physical and mechanical tests Determination of tensile str

12、ength and percentage extension ISO 3377-2, Leather Physical and mechanical tests Determination of tear load Part 2: Double edge tear ISO 3380, Leather Physical and mechanical tests Determination of shrinkage temperature up to 100 C ISO 4044, Leather Chemical tests Preparation of chemical test sample

13、s ISO 4045, Leather Chemical tests Determination of pH ISO 11640, Leather Tests for colour fastness Colour fastness to cycles of to-and-fro rubbing ISO 11641, Leather Tests for colour fastness Colour fastness to perspiration ISO 14930:2012(E) 2 ISO 2012 All rights reserved3 Terms and definitions For

14、 the purposes of this document, the following terms and definitions apply. 3.1 alum tanned leather tawed leather leather prepared solely with a mixture of which the essential active ingredient is an aluminium salt, and often, but not necessarily, alum-egg yolk and flour NOTE The natural colour of th

15、e leather is white. 3.2 chamois leather leather made from the flesh split of sheep, goat or lamb skin, or from sheep or lamb skin from which the grain has been removed by frizing and tanned by processes involving the oxidation of fish or marine animal oils in the skin, using either solely such oils

16、(full-oil chamois) or first an aldehyde and then such oils (combination chamois) 3.3 chrome-alum tanned leather leather that has first been chrome tanned throughout its thickness, then further treated or tanned with aluminium tanning agent 3.4 chrome tanned leather leather tanned either solely with

17、chromium salts or with chromium salts together with quite small amounts of some other tanning agent used merely to assist the chrome-tanning process, and not in sufficient amount to alter the essential chrome-tanned character of the leather 4 Requirements Leather for dress gloves shall conform to th

18、e requirements given in Table 1. Table 1 Requirements for leather for dress gloves Characteristics Requirements Test method pH of aqueous extract pH of aqueous extract 3,5 If the pH value is below 4, pH shall be 0,7. ISO 4045 Shrinkage temperature 90 C ISO 3380 Colour fastness to to-and-fro rubbing

19、Change of colour and staining of the felt pad to be assessed Dry felt 50 cycles 3 grey scale Wet felt 10 cycles 2 grey scale ISO 11640 Tear strength 15,0 N ISO 3377-2 Colour fastness to perspiration 3 grey scale (for unlined gloves) ISO 11641 to light 3 blue scale ISO 105-B02 Elongation at 2 N/mm 2

20、, in percent 20 % ISO 3376 ISO 14930:2012(E) ISO 2012 All rights reserved 35 Sampling 5.1 When possible, the location and identification of laboratory samples shall be in accordance with ISO 2418. 5.2 The number of samples shall be by agreement between the interested parties, except in cases of disp

21、ute when the number of samples shall be in accordance with ISO 2588. If the lot size of the leathers is high, the maximum number of samples shall be five. 6 Sample preparation and conditioning 6.1 Samples for physical and fastness tests shall be prepared and conditioned in accordance with ISO 2419.

22、6.2 Samples for chemical analysis shall be prepared in accordance with ISO 4044. 7 Test report The test report shall contain at least the following information: a) reference to this International Standard; b) results of the tests listed in Table 1; c) date and place of tests; d) full details for the identification of samples; e) any deviations from this International Standard or the test procedures used. ISO 14930:2012(E) ICS 59.140.30 Price based on 3 pages ISO 2012 All rights reserved