ISO 16145-3-2012 Ships and marine technology - Protective coatings and inspection method - Part 3 Cargo oil tanks of crude oil tankers《船舶和海洋技术 防护涂层和检验方法 第3部分 原油.pdf

1、 ISO 2012 Ships and marine technology Protective coatings and inspection method Part 3: Cargo oil tanks of crude oil tankers Navires et technologie maritime Revtements de protection et mthode dinspection Partie 3: Rservoirs dhuile de chargement de rservoirs de ptrole brut INTERNATIONAL STANDARD ISO

2、16145-3 First edition 2012-10-01 Reference number ISO 16145-3:2012(E) ISO 16145-3:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec

3、tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.

4、org Web www.iso.org Published in Switzerland ISO 16145-3:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 T erms and definitions . 2 4 Symbols and abbreviated terms . 3 4.1 Symbols . 3 4.2 Abbreviated terms . 3 5 General procedu

5、res for coating work 3 6 Standard for coating work 4 6.1 Areas considered 4 6.2 Surface preparation 6 6.3 Primary surface preparation and shop priming 7 6.4 Secondary surface preparation . 9 6.5 Coating .10 6.6 Treatment for coating defects 13 7 Inspection 14 7.1 Inspection procedure .14 7.2 Coating

6、 inspection 14 7.3 Dry film thickness measurement 16 Annex A (informative) Measurement of the conductivity for abrasives .21 Annex B (informative) Measurement of water soluble salt23 Annex C (informative) Inspection items and management of inspection .25 Annex D (informative) Assessment of the degre

7、e of damage 30 Annex E (informative) Standard for coating technical file (CTF) .31 Bibliography .40 ISO 16145-3:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St

8、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also

9、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committee

10、s is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib

11、ility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16145-3 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 8, Ship design. ISO 16145 cons

12、ists of the following parts, under the general title Ships and marine technology Protective coatings and inspection method: Part 1: Dedicated sea water ballast tanks Part 2: Void spaces of bulk carriers and oil tankers Part 3: Cargo oil tanks of crude oil tankers The following parts are under prepar

13、ation: Part 4: Automated measuring method for the total amount of water-soluble salts Part 5: Assessment method for coating damages iv ISO 2012 All rights reserved ISO 16145-3:2012(E) Introduction The ISO 16145 series addresses qualified coating and inspection works in accordance with the requiremen

14、ts of IMO PSPC. Technical Committee ISO/TC 8, Ships and marine technology, SC 8, Ship design has decided to standardize a coating and inspection method for the IMO PSPC series. Coating quality itself depends largely on the surface preparation and coating application. Therefore, the right application

15、 of surface preparation and coating in accordance with coating manufacturers recommendations including inspections at each step are of vital importance. This part of ISO 16145 is intended to serve as a standard for ship owners, shipyards, coating manufacturers, coating inspectors and coating applica

16、tors in applying IMO PSPC in the new building stage. ISO 2012 All rights reserved v Ships and marine technology Protective coatings and inspection method Part 3: Cargo oil tanks of crude oil tankers 1 Scope This part of ISO 16145 specifies a method of protective coatings and its inspection of cargo

17、oil tanks for crude oil tankers of not less than 5 000 tones deadweight, which are contracted for new building on or after 1 January 2013; or in the absence of a building contract, the keels of which are laid or which are at a similar stage of construction on or after 1 July 2013; or the delivery of

18、 which is on or after 1 January 2016. NOTE A crude oil tanker is an oil tanker engaged in the trade of carrying crude oil. This part of ISO 16145 applies to crude oil tankers and crude oil/product carriers as defined in items 1.11.1 or 1.11.4 of the Supplement to the International Oil Pollution Prev

19、ention Certificate (Form B). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

20、document (including any amendments) applies. ISO 8501-1:2007, Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall remov

21、al of previous coatings ISO 8501-3:2001 1) , Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 3: Preparation grades of welds, cut edges and other areas with surface imperfections ISO 8502-3:1992, Preparation of steel subs

22、trates before application of paints and related products Tests for the assessment of surface cleanliness Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) ISO 8502-9:1998, Preparation of steel substrates before application of paints and related produ

23、cts Tests for the assessment of surface cleanliness Part 9: Field method for the conductometric determination of water- soluble salts ISO 8503-1:2012, Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates

24、 Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive ISO 8503-2:2012, Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part 2: Method for the gra

25、ding of surface profile of abrasive blast-cleaned steel Comparator procedure IACS UI SC223, For Application of SOLAS Regulation II-1/3-2 Performance Standard for Protective Coatings (PSPC) for Dedicated Seawater Ballast Tanks in All Types of Ships and Double-side Skin Spaces of Bulk Carriers, adopte

26、d by Resolution MSC.215 (82) IMO Res.MSC.288 (87), Performance standard for protective coatings for cargo oil tanks of crude oil tankers 1) Withdrawn International Standard revised by ISO 8501-3:2006. INTERNATIONAL STANDARD ISO 16145-3:2012(E) ISO 2012 All rights reserved 1 ISO 16145-3:2012(E) 3 T e

27、rms and definitio ns For the purposes of this document, the following terms and definitions apply. 3.1 90/10 rule rule according to which 90% of all thickness measurements should be greater than or equal to nominal dry film thickness (NDFT) and none of the remaining 10% measurements shall be below 9

28、0% of NDFT 3.2 abrasive metallic or non-metallic particles which are used in blasting work for removing mill scale, rust or foreign substance on the surface to be coated using pressurized air or a high-speed rotating impeller NOTE A steel shot ball is used mainly in the primary surface preparation a

29、nd steel grit is used mainly in the secondary surface preparation; however, garnet or non-metallic abrasives may be used in some circumstances. 3.3 coating inspector qualified person certified to at least NACE Coating Inspector Level 2, FROSIO Inspector Level III, or an equivalent qualification with

30、 at least two years documented relevant coating inspection experience and as agreed by ship owner, shipyard and coating manufacturer as specified in IACS UI SC223, adopted by Resolution MSC.215 (82) 3.4 erection final assembly of blocks or pre-erected blocks EXAMPLE On the dry dock or ground buildin

31、g berth. 3.5 line quality controller line QC person, other than the coating inspector or assistant to the coating inspector, who carries out the inspection work prior to the official inspection 3.6 m ea s urem ent of represent at iv e dr y fil m thickness (D F T ) measurement of typical dry film thi

32、ckness (DFT) after each main coating in order to use it as a reference in a follow-up coating by measuring the film thickness of certain representative parts of the compartment NOTE It is not necessary to keep a record of the representative DFT. 3.7 pre-erection assembly of blocks in large units cor

33、responding to the crane capacity for erection 3.8 shop primer prefabrication primer coating applied to steel plates, often in automatic plants (and before the first coat of a coating system) 3.9 stain light shadows, slight streaks or minor discolorations 2 ISO 2012 All rights reserved ISO 16145-3:20

34、12(E) 4 Symbols and abbreviated terms 4.1 Symbols C m electric conductivity of solutions C s electric conductivity of abrasive K cell constant 4.2 Abbreviated terms CTF coating technical file DFT dry film thickness FROSIO Faglig Rd for Opplring og Sertifisering av Inspektrer innen Overflatebehandlin

35、g (The Norwegian Professional Council for Education and Certification of Inspectors for Surface Treatment) IACS International Association of Classification Societies Ltd IMO International Maritime Organization JSRA-SPSS The Shipbuilding Research Association of Japan - Standard for the preparation of

36、 steel surface prior to painting JSTRA SPSS for PSPC Japan Ship Technology Research Association - Standard for the preparation of steel substrate for PSPC (SPSS for PSPC) NACE NACE International NDFT nominal dry film thickness PSPC performance standard for protective coatings QA quality assurance QC

37、 quality control SOC statement of compliance SSPC The Society for Protective Coatings (former Steel Structure Painting Council, USA) TAC type approval certificate COT cargo oil tank 5 General procedures for coating work The typical hull construction process for coating is listed in Table 1 below. IS

38、O 2012 All rights reserved 3 ISO 16145-3:2012(E) Table 1 Typical coating and inspection steps for hull structure Step Item Description 1 Storage of steel Storage area for plates and profiles. 2 Primary surface preparation (pre-treatment) and shop priming Remove mill scale, rust, and other contaminan

39、ts and apply shop primer. Details are given in 6.2. 3 Inspection for primary surface preparation and shop priming Carry out a self-inspection in accordance with the QA system. The QA system contains a regular check and record of surface cleanness, surface profile, DFT measurement, salt measurement,

40、etc. 4 Steel cutting Cut steel for assembly. 5 Sub-assembly Primary assembly step on a small or medium scale. Carry out the work including edge preparation in accordance with ISO 8501-3:2001 (P2 grade). Details are given in 6.3.3 for edge preparation. 6 Block assembly or unit and panel assembly A st

41、ep of assembling the members assembled in a small or medium scale into block unit. Carry out the work including edge preparation in accordance with ISO 8501-3:2001 (P2 grade). Details are given in 6.3.3 for edge preparation. 7 Pre-outfitting Install outfits such as pipes and supports prior to block

42、coating. 8 Secondary surface preparation (block stage) Details are given in 6.4 for the secondary surface preparation for completed block. 9 Inspection for secondary surface preparation (block stage) Inspection by a coating inspector (or an assistant to coating inspector under direct supervision of

43、the coating inspector). 10 Block coating Details are given in 6.5 for the step of coating on the block where surface preparation and inspection are completed. 11 Inspection for block coating Inspection by a coating inspector (or an assistant to coating inspector under direct supervision of the coati

44、ng inspector). 12 Pre-erection Assemble blocks in large units corresponding to the crane capacity for erection. 13 Secondary surface preparation and coating for pre-erection joint Details are given in 6.4 and 6.5 for surface preparation and coating work of the welding joint of pre-erection. 14 Inspe

45、ction for pre-erection joint Inspection by a coating inspector (or an assistant to coating inspector under direct supervision of the coating inspector). 15 Erection Final assembly step of blocks or pre-erected blocks on the dry dock or ground building berth. 16 Secondary surface preparation and coat

46、ing for erection joint Details are given in 6.4 and 6.5 for the step of secondary surface preparation and coating work on erection joint. 17 Inspection erection joint Inspection by a coating inspector (or an assistant to coating inspector under direct supervision of the coating inspector). 18 Comple

47、tion Completion and final coating touch up and repair. Steps 12 to 14 may be omitted depending on the size of blocks and the conditions of each shipyard. 6 Standard for coating work 6.1 Areas considered The following areas are the minimum areas that shall be coated according to IMO Res.MSC.288 (87).

48、 See Figure 1. a) Deckhead with complete internal structure, including brackets connecting to longitudinal and transverse bulkheads. In tanks with ring frame girder construction, the under deck transverse framing shall be coated down to the level of the first tripping bracket below the upper facepla

49、te. 4 ISO 2012 All rights reserved ISO 16145-3:2012(E) b) Longitudinal and transverse bulkheads shall be coated to the uppermost means of access level. The uppermost means of access and its supporting brackets shall be fully coated. c) On cargo tank bulkheads without an uppermost means of access the coating shall extend to 10 % of the height of the tank at centre line but need not extend more than 3 m down from the deck. d) The flat inner bottom and all structures to a height of 0,3 m above t