ISO 17612-2004 Tractors and machinery for agriculture and forestry - Auxiliary-power-transmission connector for the operator station《农业和林业用牵引车和机械 操纵台用辅助动力传输连接器》.pdf

1、INTERNATIONAL STANDARD ISO 17612 First edition 2004-02-15 Reference number ISO 17612:2004(E) ISO 2004 Tractors and machinery for agriculture and forestry Auxiliary-power- transmission connector for the operator station Tracteurs et matriels agricoles et forestiers Connecteur de transmission dnergie

2、auxiliaire au poste de loprateurISO 17612:2004(E) ii ISO 2004 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed t

3、o and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the sof

4、tware products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it

5、is found, please inform the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permiss

6、ion in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandISO 17612:2004(E) ISO 2004 All

7、rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a s

8、ubject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission

9、IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical comm

10、ittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not

11、be held responsible for identifying any or all such patent rights. ISO 17612 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tr a c t o r s.ISO 17612:2004(E) iv ISO 2004 All rights reserved Introduction This International Standar

12、d specifies an electrical connector for the transmission of auxiliary power within the operator station of enclosed agricultural machines. The specification thus established will allow manufacturers to provide both individual and multiple outlets in the cab. Typical applications include monitors, li

13、ght-duty controllers, remote operating devices and miscellaneous off-the-shelf items. Only the application dimensions and electrical characteristics are covered. Other electrical transmission connectors for agricultural tractors and machinery are specified in ISO/TR 12369. For this and other Interna

14、tional Standards dealing with connectors for electrical power transmission from tractor to implement or other means, see the Bibliography.INTERNATIONAL STANDARD ISO 17612:2004(E) ISO 2004 All rights reserved 1 Tractors and machinery for agriculture and forestry Auxiliary- power-transmission connecto

15、r for the operator station 1S c o p e This International Standard specifies the essential interface dimensions of a connector and its plug for the transmission of electrical power within the enclosed operator station of agricultural tractors and machinery. The device is intended to be used as a non-

16、environmentally sealed, convenient source for power auxiliary devices, providing a means for the operator to obtain electrical power without altering the tractor/machine electrical wiring harness. The maximum current capacity of the specified device is : it is not applicable to any other voltage sys

17、tem ( or ). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, Ge

18、neral tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 contact current-carrying element of the connector, either male or female 3.2 pin ma

19、le contact 3.3 contact socket female contact 3.4 power strip socket female half of the connector, integral to the power strip 3.5 power strip plug male half of the connector, attached to the device to be powered 3.6 connector complete mated assembly containing socket, plug, pins and contact sockets

20、12 V 30 A 6 V 24 VISO 17612:2004(E) 2 ISO 2004 All rights reserved 3.7 power strip connector containing one or more distribution positions 3.8 switched current electrical current path containing a switching component between battery and power strip 3.9 un-switched current electrical current path hav

21、ing an uninterrupted current path between battery and power strip 3.10 auxiliary device device attached to the power strip plug EXAMPLE Monitor, controller, communication device, computer. 4 Requirements 4.1 Dimensional requirements 4.1.1 Power strip socket The connector shall consist of a base cont

22、aining one or more sockets. Each socket shall be covered with a lid, which shall be spring-loaded to close or have a detent to hold it in the closed position. The lid shall have symbols defining the contact positions and their respective use. A typical example is shown in Figure 1, for reference pur

23、poses only. The socket and pin spacing dimensions shall be in accordance with Figure 2. Female contacts shall be of at least a tin-plated material designed to mate with the male contacts specified in Figure 3. 4.1.2 Power strip plug Critical outside dimensions of the power strip plug shall be in acc

24、ordance with Figure 4 to allow typical mating with the power strip socket.ISO 17612:2004(E) ISO 2004 All rights reserved 3 Dimensions in millimetres Figure 1 Typical power strip socket (for information only)ISO 17612:2004(E) 4 ISO 2004 All rights reserved Dimensions in millimetres, tolerances in acc

25、ordance with ISO 2768-m Figure 2 Socket and pin spacing dimensions Dimensions in millimetres, tolerances in accordance with ISO 2768-m Figure 3 Male contacts of power strip plugISO 17612:2004(E) ISO 2004 All rights reserved 5 Dimensions in millimetres, tolerances in accordance with ISO 2768-m Figure

26、 4 Power strip plugISO 17612:2004(E) 6 ISO 2004 All rights reserved 4.2 Electrical requirements 4.2.1 Voltage There shall be a nominal voltage of d.c. at Contacts A and C, with reference to Contact B, at the vehicle rated engine speed. See Table 1. 4.2.2 Current The “sum” of the switched and unswitc

27、hed current at any one connector (socket) shall be specified to be a maximum of . Total current draw of a multiple connector power strip shall not exceed . 4.2.3 Contact electrical requirements Circuit protections of Contacts A and C shall be provided based on the maximum current capacity of the ele

28、ctrical circuit (sourced from an electrical distribution centre) and shall not exceed . Contact B shall have a dedicated electrical path direct to a convenient termination point near, or at, the frame ground point of the battery. 4.2.4 Contact layout and function The layout of the contacts shall be

29、as shown in Figures 2, 3 and 4. Contacts shall have contact designation, symbol and function in accordance with Table 1. Table 1 Contact designation, function and symbol Contact designation Function Symbol ContactA Unswitched d.c. A Contact B Negative battery reference (Ground) B ContactC Switched d

30、c. C +12 V 30 A 30 A 30 A +12 V +12 VISO 17612:2004(E) ISO 2004 All rights reserved 7 Bibliography 1 ISO 1724, Road vehicles Connectors for the electrical connection of towing and towed vehicles 7- pole connector type 12 N (normal) for vehicles with 12 V nominal supply voltage 2 ISO 8092-2, Road ve

31、hicles Connections for on-board electrical wiring harnesses Part 2: Definitions, test methods and general performance requirements 3 ISO 8935, Tractors for agriculture and forestry Mountings and apertures for external equipment controls 4 ISO/TR 12369, Agricultural tractors and machinery Electrical power transmission connectorsISO 17612:2004(E) ICS 65.060.10 Price based on 7 pages ISO 2004 All rights reserved