ISO 18418-1-2016 Gasoline engines - Medium pressure liquid fuel supply connections - Part 1 60female cone connectors《汽油发动机 中压液体燃料供应连接 第1部分 60 内锥接头》.pdf

1、 ISO 2016 Gasoline engines Medium pressure liquid fuel supply connections Part 1: 60 female cone connectors Moteurs essence Connexions pour des lignes de combustible liquide moyenne pression Partie 1: Raccords cnes femelle de 60 INTERNATIONAL STANDARD ISO 18418-1 Second edition 2016-12-01 Reference

2、number ISO 18418-1:2016(E) ISO 18418-1:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic o

3、r mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Ge

4、neva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 18418-1:2016(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Requirements 1 4.1 Dimensions and tolerances 1 4.2 Materials . 3 5 Operating pressure 3 6 Design

5、ation 3 Bibliography 4 ISO 2016 All rights reserved iii Contents Page ISO 18418-1:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried ou

6、t through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO co

7、llaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different app

8、roval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the

9、 subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any

10、 trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organi

11、zation (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 34, Propulsion, powertrain, and powertrain fluids. This second edition cancels and replaces

12、the first edition (ISO 18418-1:2014), which has been technically revised. A list of all parts in the ISO 18418 series can be found on the ISO website.iv ISO 2016 All rights reserved ISO 18418-1:2016(E) Introduction Some spark ignition (SI) engines use direct injection (DI) fuel systems which supply

13、gasoline under pressure to a rail and to the injectors via pipe assemblies with a 60 female cone connector. Such components are similar to ISO 2974 and ISO 13296 for the diesel injection systems, except for the relationship between the outside and inside diameters of the pipes due to the lower press

14、ure range. Connectors defined either in ISO 2974 or in this document can be used. ISO 2016 All rights reserved v Gasoline engines Medium pressure liquid fuel supply connections Part 1: 60 female cone connectors 1 Scope This document specifies the dimensional requirements of medium-pressure pipe end-

15、connections for gasoline (spark ignition) engine fuel injection equipment. It is applicable to externally threaded end-connections having a 60 female cone (see Figure 1), as well as to the pipe end assemblies of medium-pressure fuel injection pipes with outside diameters of up to and including 10 mm

16、 (see Table 1). 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced doc

17、ument (including any amendments) applies. ISO 261, ISO general purpose metric screw threads General plan 3 T erms a nd definiti ons No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electrope

18、dia: available at http:/ /www.electropedia.org/ ISO Online browsing platform: available at http:/ /www.iso.org/obp 4 Requirements 4.1 Dimensions and tolerances Figure 1 indicates the basic requirements for the end-connection at the rail, at the fuel injection pump, and at the injector to allow inter

19、changeability for medium-pressure fuel injection pipe assemblies. The 60 female cone and its relationship to the external thread of the end-connection shall meet the requirements of Figure 1. It is important that the dimensions and tolerances are valid after the final assembly (heat treating, brazin

20、g, welding) of the end-connection to the rail, the pump, or the injector and prior to the assembly of the pipe. Dimensions and tolerances are given in Table 1. Unspecified details are left to the manufacturers choice. INTERNATIONAL ST ANDARD ISO 18418-1:2016(E) ISO 2016 All rights reserved 1 ISO 184

21、18-1:2016(E) Dimensions in millimetres Surface roughness in micrometres, as defined in ISO 1302 A S F E T a Key A thread S reference diameter E depth of reference diameter plane F bore diameter T connector length a Undercut: design according to agreement between customer and supplier maintaining a m

22、inimum thread engagement of 3x pitch when assembled with pipe end nut. NOTE 1 See Table 1 for dimensions of A, S, E, F, and T. NOTE 2 All non-dimensioned edges . Figure 1 End-connector with integral 60 female cone2 ISO 2016 All rights reserved ISO 18418-1:2016(E) Table 1 60 female cones Dimension in

23、 millimetres Tube outside diameter Thread aA Reference diameter S Bore diameter F max. Depth of reference diameter plane E Connector length T min. 8 M14 1,5 8,5 6,1 2,2 0,08 11 10 M16 1,5 8,5 8,1 3,9 0,08 11 aTolerance classes of threads 6 g for external threaded end-connection. 4.2 Materials The sp

24、ecification of material and heat treatment shall be made according to the intended use. 5 Operating pressure The permissible operating pressure shall be specified with an adequate safety margin to ensure the sealing of the joint under maximum internal pressure and shall be agreed upon between suppli

25、er and customer. 6 Designation An end-connection conforming to this document shall be designated by the following elements, in the order given: a) a reference to this document, i.e. ISO 18418-1; b) the tube outside diameter, in millimetres (mm); c) the thread designation, in accordance with ISO 261.

26、 EXAMPLE An end-connection of pipe outside diameter 8 mm, with an M14 thread is designated: ISO 18418-1 - M14 ISO 2016 All rights reserved 3 ISO 18418-1:2016(E) Bibliography 1 ISO 1302, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 2 ISO 29

27、74, Diesel engines 60 degree female cones for high-pressure fuel injection components 3 ISO 3508, Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO 262 4 ISO 13296, Diesel engines High-pressure fuel injection pipe assemblies General requirements and dimensions 5 ISO 18418-2, Gasoline engines Medium pressure liquid fuel supply connections Part 2: Pipe assemblies4 ISO 2016 All rights reserved ISO 18418-1:2016(E) ISO 2016 All rights reserved IC S 43.060.40 Price based on 4 pages