ISO 23206-2005 Agricultural wheeled tractors and attachments - Front loaders - Carriages for attachments《农用轮式拖拉机及附件 前端式装载机 附件用拖板》.pdf

1、 Reference number ISO 23206:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 23206 First edition 2005-06-01 Agricultural wheeled tractors and attachments Front loaders Carriages for attachments Tracteurs agricoles roues et accessoires Chargeuses frontales Accouplements sur structures pour les accessoires

2、ISO 23206:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downl

3、oading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the

4、General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address g

5、iven below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs memb

6、er body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 23206:2005(E) ISO 2005 All rights reserved iiiForeword ISO

7、(the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical comm

8、ittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrote

9、chnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the memb

10、er bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifyi

11、ng any or all such patent rights. ISO 23206 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. INTERNATIONAL STANDARD ISO 23206:2005(E) ISO 2005 All rights reserved 1Agricultural wheeled tractors and attachments Front load

12、ers Carriages for attachments 1 Scope This International Standard specifies the dimensions and clearance requirements for the carriages for attachments on agricultural tractors and machines equipped with front loaders and having a maximum load capacity of 30 kN and a maximum unladen tractor weight o

13、f 7 500 kg. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 front loader detachable unit consisting of lifting arms and fastening devices designed to be mounted on a frame on the front of a tractor and equipped with a carriage for mounting va

14、rious attachments See Figure 1. 2.2 attachment working device to be mounted on and operated with a front loader See Figure 1. Key 1 attachment 2 carriage 3 lifting arm Figure 1 Tractor with front loader and an attachment ISO 23206:2005(E) 2 ISO 2005 All rights reserved2.3 carriage coupler assembly a

15、t the front loader arm end for mounting various attachments to the front loader See Figure 1. 2.4 maximum load capacity maximum vertical lift capacity generated at a point 800 mm horizontal in front of the locking pin of the carriage, when operating the lift and/or tilt cylinders See Figure 2. Dimen

16、sions in millimetres Figure 2 Maximum load capacity 3 Dimensions and clearances The carriage dimensions and the dimensions associated with the attachment shall be in accordance with Figures 3 and 4. For the carriage clearance zones, see Figure 3. For the clearance at the back of the attachment, see

17、Figure 5. ISO 23206:2005(E) ISO 2005 All rights reserved 3Dimensions in millimetres Key 1 clearance zone for hook 2 clearance zone for eyelet 3 buffer for attachment 4 border of front of carriage 5 locking pin Figure 3 Carriage dimensions and clearances ISO 23206:2005(E) 4 ISO 2005 All rights reserv

18、edDimensions in millimetres Key 1 hook 2 eyelet 3 attachment buffer aaThe buffer shall be wide enough (W 790 mm) so that the attachment does not deform the carriage during normal operation. Figure 4 Dimensions associated with the attachment ISO 23206:2005(E) ISO 2005 All rights reserved 5Dimensions

19、in millimetres Key 1 clearance Figure 5 Clearance at back of attachment ISO 23206:2005(E) 6 ISO 2005 All rights reserved4 Requirements 4.1 General The front loader manufacturer shall specify the type and capacity of the allowable attachments that can be fitted and safely operated. 4.2 Locking device

20、 The locking pin on the carriage as shown in Figure 3 may be placed either inside or outside of the frame. 4.3 Locking and unlocking Locking and unlocking of the carriage to the attachment may be operated either from the drivers seat or from a place near the locking device. A means of visually verif

21、ying that the locking process is completed shall be provided such that it is visible from the position where the locking device is operated. 4.4 Clearance zones Clearance zones 1 and 2 according to Figure 3 and the clearance at the back of the attachment as shown in Figure 5 shall be maintained to f

22、acilitate the coupling process. 4.5 Mounting height of eyelet to an attachment The recommended distance between the base surface and the centre of the eyelet is W 150 mm. See Figure 6. Dimensions in millimetres Key 1 attachment 2 base surface Figure 6 Mounting height of eyelet to an attachment ISO 23206:2005(E) ICS 65.060.10 Price based on 6 pages ISO 2005 All rights reserved