ISO 25297-2-2011 Optics and photonics - Electronic exchange of optical data - Part 2 Mapping to the classes and properties defined in ISO 23584《光学和光子学 光学数据的电子交换.pdf

1、 Reference number ISO 25297-2:2011(E) ISO 2011INTERNATIONAL STANDARD ISO 25297-2 First edition 2011-12-15 Optics and photonics Electronic exchange of optical data Part 2: Mapping to the classes and properties defined in ISO 23584 Optique et photonique Transfert lectronique des donnes optiques Partie

2、 2: Mappage des classes et proprits definies dans lISO 23584 ISO 25297-2:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopy

3、ing and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerl

4、and ii ISO 2011 All rights reservedISO 25297-2:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Mapping 1 4.1 General . 1 4.2 Mapping table 2 Annex A (informative) Class hierarchy . 22 Bibliography 23 ISO 25297-2:2011(

5、E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int

6、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic

7、al Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the

8、technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

9、ISO shall not be held responsible for identifying any or all such patent rights. ISO 25297-2 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 1, Fundamental standards. ISO 25297 consists of the following parts, under the general title Optics and photonics Electro

10、nic exchange of optical data: Part 1: NODIF information model Part 2: Mapping to the classes and properties defined in ISO 23584 INTERNATIONAL STANDARD ISO 25297-2:2011(E) ISO 2011 All rights reserved 1Optics and photonics Electronic exchange of optical data Part 2: Mapping to the classes and proper

11、ties defined in ISO 23584 1 Scope This International Standard specifies the relationship between the terms used in ISO 25297-1 and the properties defined in ISO 23584-2, and provides the means to facilitate the use of both standards. NOTE This International Standard does not define all attributes of

12、 properties in ISO 23584-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

13、. ISO 25297-1:2010, Optics and photonics Electronic exchange of optical data Part 1: NODIF information model ISO 23584-1, Optics and photonics Specification of reference dictionary Part 1: General overview on organization and structure ISO 13584-42, Industrial automation systems and integration Part

14、s library Part 42: Description methodology: Methodology for structuring parts families 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 25297-1, ISO 23584-1 and ISO 13584-42 apply. 4 Mapping 4.1 General The terms of the application objects and their a

15、ttributes in NODIF are used as the preferred names in the reference dictionary. Underscores used in the terms in NODIF are omitted in the reference dictionary. NOTE The reference dictionary ID numbers given for the keywords will be filled once they are registered in the ISO/TC 172 reference dictiona

16、ry database, which is under construction. ISO 25297-2:2011(E) 2 ISO 2011 All rights reserved4.2 Mapping table Table 1 and Table 2 show the relationship between keywords in NODIF and the classes and properties in the ISO/TC 172 reference dictionary. Class hierarchy is depicted in Annex A for referenc

17、e. ISO 25297-2:2011(E) Table 1 Mapping of the terms of classes in NODIF to the reference dictionary NODIF keyword Hierarchy Super class Preferred name Definition Note Reference dictionary ID number aperture Application class ISO TC172SC1/NODIF aperture application object to describe aperture of opti

18、cal system 4.3.25.6, 4.3.26.8 aperture in NODIF Assembly_tolerance Application class ISO TC172SC1/NODIF assembly tolerance application object to specify assembly tolerance 4.3.18 Assembly_tolerance in NODIF Diffractive_surface_description Application class ISO TC172SC1/NODIF diffractive surface desc

19、ription application object to describe diffractive optical surface 4.3.12 Diffractive_surface_description in NODIF AAA017-001 Dimensional_tolerance Application class ISO TC172SC1/NODIF dimensional tolerance application object to specify tolerance for dimensions of optical part 4.3.17 Dimensional_tol

20、erance in NODIF Material_property Application class ISO TC172SC1/NODIF material property application object to specify material 4.3.36 Material_property in NODIF Optical_design_formulation Application class ISO TC172SC1/NODIF optical design formulation application object to collect information relev

21、ant to optical design 4.3.5 Optical_design_formulation in NODIF Optical_evaluation Application class ISO TC172SC1/NODIF optical evaluation application object to describe conditions and results of optical evaluations 4.3.23 Optical_evaluation in NODIF Optical_part_view_designator Application class IS

22、O TC172SC1/NODIF optical part view designator application object to link information on optical systems/parts and the object “design discipline product definition” in ISO 10303-203 4.3.2 Optical_part_view_designator in NODIF Optical_process_specification Application class ISO TC172SC1/NODIF optical

23、process specification application object to describe machining process 4.3.15 Optical_process_specification in NODIF Optical_specification Application class ISO TC172SC1/NODIF optical specification application object to contain various specifications 4.3.13 Optical_specification in NODIF Optical_sys

24、tem_specification Application class ISO TC172SC1/NODIF optical system specification application object to contain specifications of optical system 4.3.4 Optical_system_specification in NODIF Optical_tolerance Application class ISO TC172SC1/NODIF optical tolerance application object to describe optic

25、al tolerance 4.3.16 Optical_tolerance in NODIF Other_optical_evaluation Application class ISO TC172SC1/NODIF other optical evaluation application object to describe optical evaluation based on external definition 4.3.31 Other_optical_evaluation in NODIF paraxial_ray_tracing Application class ISO TC1

26、72SC1/NODIF paraxial ray tracing application object to describe paraxial ray tracing results 4.3.24.6 paraxial_ray_tracing in NODIF 3 ISO 2011 All rights reserved ISO 25297-2:2011(E) Table 1 (continued) NODIF keyword Hierarchy Super class Preferred name Definition Note Reference dictionary ID number

27、 ray_tracing Application class ISO TC172SC1/NODIF ray tracing application object to describe real ray tracing results 4.3.25.10 ray_tracing in NODIF Specification_distinction Application class ISO TC172SC1/NODIF specification distinction application object to indicate type of optical design specific

28、ation; official specification requirements of optical system or design requirements for optical system 4.3.3 Specification_distinction in NODIF wavelength Application class ISO TC172SC1/NODIF wavelength application object to specify wavelength value or spectral line 4.3.14.5.2, 4.3.24.2, 4.3.25.5, 4

29、.3.14.5.2, 4.3.28.2 wavelength in NODIF Zone Application class ISO TC172SC1/NODIF zone application object to specify optically effective area 4.3.19 Zone in NODIF zone_form Application class ISO TC172SC1/NODIF zone form application object to describe optically effective elementary area 4.3.19.2 zone

30、_form in NODIF three-dimensional_real_vector Application class ISO TC172SC1/NODIF three-dimensional real vector data type of component consisting of three elements; vector component or direction cosine Figure A.6, Figure A.20 three- dimensional_real_vector in NODIF other_tolerance Application class

31、dimensional tolerance other tolerance application object to describe tolerance for optical part based on external definition 4.3.17.5 other_tolerance in NODIF change_position Application class multi-configuration change position application object to specify arrangement of dynamic blocks in optical

32、system 4.3.8.13 change_position in NODIF Block_description Application class optical design formulation block description application object to describe moving range of optical block 4.3.6 Block_description in NODIF Cemented_part Application class optical design formulation cemented part application

33、 object to indicate cemented optical part 4.3.7 Cemented_part in NODIF Optical_path_definition Application class optical design formulation optical path definition application object to specify data necessary to trace rays through optical system 4.3.8 Optical_path_definition in NODIF Ghost_image_eva

34、luation Application class optical evaluation ghost image evaluation application object to describe ghost image evaluation 4.3.29 Ghost_image_evaluation in NODIF Illuminance_distribution _evaluation Application class optical evaluation illuminance distribution evaluation application object to describ

35、e illuminance distribution evaluation 4.3.27 Illuminance_distribution_evaluation in NODIF 4 ISO 2011 All rights reservedISO 25297-2:2011(E) Table 1 (continued) NODIF keyword Hierarchy Super class Preferred name Definition Note Reference dictionary ID number Optical_sensitivity_evaluation Application

36、 class optical evaluation optical sensitivity evaluation application object to describe optical sensitivity evaluation 4.3.30 Optical_sensitivity_evaluation in NODIF OTF_evaluation Application class optical evaluation OTF evaluation application object to specify optical evaluation based on OTF 4.3.2

37、6 OTF_evaluation in NODIF Paraxial_evaluation Application class optical evaluation paraxial evaluation application object to describe optical evaluation by paraxial ray tracing 4.3.24 Paraxial_evaluation in NODIF Ray_tracing_evaluation Application class optical evaluation ray tracing evaluation appl

38、ication object to describe optical evaluation by real ray tracing 4.3.25 Ray_tracing_evaluation in NODIF Spectral_characteristics Application class optical evaluation spectral characteristics application object to describe spectral characteristics 4.3.28 Spectral_characteristics in NODIF surface_imp

39、erfection_evaluation Application class optical evaluation surface imperfection evaluation application object to describe surface imperfection evaluation 4.3.31 surface_imperfection_evaluation in NODIF veiling_glare_index_evaluation Application class optical evaluation veiling glare index evaluation

40、application object to describe veiling glare index evaluation 4.3.32 veiling_glare_index_evaluation in NODIF internal_transmittance Application class optical material specification internal transmittance application object to indicate internal transmittance of optical material 4.3.14.8 internal_tran

41、smittance in NODIF refractive_index_information Application class optical material specification refractive index information application object to describe refractive index values and relevant wavelength values of material 4.3.14.5 refractive_index_information in NODIF multi-configuration Applicati

42、on class optical path definition multi-configuration application object to specify information on multiple configurations in optical system 4.3.8.11 multi-configuration in NODIF non-sequential_path_range Application class optical path definition non-sequential path range application object to specif

43、y range of non-sequential path 4.3.8.6 non-sequential_path_range in NODIF Surface_interface Application class optical path definition surface interface application object to specify data for ray tracing at each interface 4.3.9 Surface_interface in NODIF Coating_specification Application class optica

44、l specification coating specification application object to describe optical coating 4.3.20 Coating_specification in NODIF Optical_material_specification Application class optical specification optical material specification application object to contain specification of optical material 4.3.14 Opti

45、cal_material_specification in NODIF 5 ISO 2011 All rights reserved ISO 25297-2:2011(E) Table 1 (concluded) NODIF keyword Hierarchy Super class Preferred name Definition Note Reference dictionary ID number Protective_surface_treatment Application class optical specification protective surface treatme

46、nt application object to describe treatment process onto optical surface; black painting to prevent stray light or protect optical part 4.3.21 Protective_surface_treatment in NODIF User-defined_specification Application class optical specification user-defined specification application object to spe

47、cify item based on external definition 4.3.22 User-defined_specification in NODIF aspheric_coefficient Application class optical surface description aspheric coefficient application object to describe coefficient of power series in polynomial terms of generalized aspheric surface when surface is rot

48、ationally symmetric about z-axis 4.3.11.3.11 aspheric_coefficient in NODIF user-defined_surface_coefficient Application class optical surface description user-defined surface coefficient application object to specify name and value of coefficient for “user- defined surface” 4.3.11.3.18 user- defined

49、_surface_coefficient in NODIF user-defined_surface_reference Application class optical surface description user-defined surface reference application object to specify external file reference to contain expression based on external definition 4.3.11.3.17 user- defined_surface_reference in NODIF surface_form_tolerance Application class optical tolerance surface form tolerance application object to describe tolerance for optical surf