ISO 25947-1-2017 Fireworks - Categories 1 2 and 3 - Part 1 Terminology《烟花 1 2和3类 第1部分 术语》.pdf

1、 ISO 2017 Fireworks Categories 1, 2 and 3 Part 1: Terminology Artifices de divertissement Catgories 1, 2 et 3 Partie 1: Terminologie INTERNATIONAL STANDARD ISO 25947-1 First edition2017-04 Reference number ISO 25947-1:2017(E)ISO 25947-1:2017(E) ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOC

2、UMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior writte

3、n permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgISO 25947-1:

4、2017(E) Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 Bibliography 6 Alphabetical index 7 ISO 2017 All rights reserved iii Contents PageForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member

5、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental

6、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance ar

7、e described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention

8、is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/

9、or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms a

10、nd expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso. org/ iso/ foreword. html. This document was prepared by Technical Committee ISO/TC 2

11、64, Fireworks. A list of all the parts in the ISO 25947 series can be found on the ISO website. ISO 25947-1:2017(E) iv ISO 2017 All rights reservedINTERNATIONAL ST ANDARD ISO 25947-1:201 7(E) Fireworks Categories 1, 2 and 3 Part 1: Terminology 1 Scope This document defines various terms relating to

12、the design, construction, primary packaging and testing of fireworks of categories 1, 2 and 3. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition

13、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 25947-2, Fireworks Categories 1, 2 and 3 Part 2: Categories and types of firework 3 T erms a nd definiti ons For the purposes of this document, the following terms and definit

14、ions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp 3.1 acceptance quality limit AQL quality level t

15、hat is the worst tolerable process average when a continuing series of lots is submitted for acceptance sampling SOURCE: ISO 28591:1999, 3.1.26 3.2 batch test test performed on a sample of products taken at random from a production batch to check compliance with a given standard Note 1 to entry: Bat

16、ch testing needs all products in the production batch to comply with the characteristics the standard requires to ensure homogeneity of the whole batch. It aims to prove that all products which are placed on the market are in conformity with the type which is described in the typeexamination certifi

17、cate and have been successfully submitted to type tests as determined by the standard. 3.3 black powder intimate mixture of charcoal and sodium nitrate or potassium nitrate with or without sulfur 3.4 burning rate of composition net explosive content (3.27) in grams divided by the effect time in seco

18、nds ISO 2017 All rights reserved 13.5 bursting charge pyrotechnic composition (3.36) which is intended to burst open the firework case (3.14), in order to expel one or more pyrotechnic units (3.37), which can also transmit ignition 3.6 critical nonconforming unit nonconforming unit (3.28) with one o

19、r more critical nonconformities (3.7), with or without major (3.24) or minor nonconformities (3.26) 3.7 critical nonconformity nonconformity (3.29) that judgement and experience indicate is likely to result in hazardous or unsafe conditions Note 1 to entry: This type of nonconformity is referred to

20、as a “class A nonconformity” in ISO 28591:1999. 3.8 debris any part of the firework (3.15) which remains after the firework has ceased to function 3.9 droop angle by which the tip of a compositioncoated wire has been deflected from the horizontal, after the firework (3.15) has ceased to burn 3.10 ef

21、fect charge pyrotechnic composition (3.36), other than propellant charge (3.34) or bursting charge (3.5), which, upon functioning, will burn or explode to produce a visual and/or aural effect 3.11 end closure part or crimp which is designed to seal one end of a firework case (3.14) 3.12 explosion su

22、dden release of energy accompanied by a report with or without a flash 3.13 external support support which is not integral to the article, or which has to be fixed to the article before use by the user to provide stability Note 1 to entry: External support includes but is not limited to: burying the

23、 article in soft ground or material, fixing the article to a post or using heavy objects (e.g. sand bags). 3.14 f i r e w o rk c a s e container which is designed to retain pyrotechnic compositions (3.36) within a firework (3.15) Note 1 to entry: According to its mechanical strength, this container

24、may intentionally (by design) influence the fireworks behaviour. 3.15 f i r ewor k device containing pyrotechnic composition (3.36) which, upon functioning, will burn and/or explode to produce a visual or aural effect or movement, or a combination of such effects, intended as a direct form of entert

25、ainment ISO 25947-1:2017(E) 2 ISO 2017 All rights reserved3.16 f i r s t p r i n c i p a l e f f e c t principal effect (3.32) of a firework (3.15) which is the first to occur during the functioning of the firework 3.17 friction head ignition head (3.18) designed to be ignited by friction 3.18 ignit

26、ion head initial fuse (3.20) consisting of pyrotechnic composition (3.36) only 3.19 initial fuse burning burning which immediately follows ignition and precedes any effect 3.20 initial fuse component of a firework (3.15) which is ignited in order to start the firework functioning 3.21 invisible burn

27、ing time time between the preliminary effect (3.30) and first principal effect (3.16) 3.22 invisible burning burning occurring within the firework (3.15) which is not visible to the person who ignited the firework 3.23 major nonconforming unit nonconforming unit (3.28) with one or more major nonconf

28、ormities (3.24), with or without minor nonconformities (3.26), but with no critical nonconformities (3.7) 3.24 major nonconformity nonconformity (3.29), other than a critical nonconformity (3.7), which is likely to result in failure, to reduce materially the usability of the firework (3.15), or to i

29、ncrease the potential hazard Note 1 to entry: This type of nonconformity is referred to as a “class B nonconformity” in ISO 28591:1999. 3.25 minor nonconforming unit nonconforming unit (3.28) with one or more minor nonconformities (3.26), but with no critical (3.7) or major nonconformities (3.24) 3.

30、26 minor nonconformity nonconformity (3.29) that is not likely to reduce materially the usability of the firework (3.15) Note 1 to entry: This type of nonconformity is referred to as a “class C nonconformity” in ISO 28591. 3.27 net explosive content NEC mass of pyrotechnic composition (3.36) in the

31、firework (3.15), excluding the pyrotechnic composition in the initial fuse (3.20) or transmitting fuses (3.34), friction or ignition heads (3.18) Note 1 to entry: Net explosive quantity or net equivalent quantity (NEQ), net explosive mass (NEM), or net explosive weight (NEW) are often used to convey

32、 the same meaning. ISO 25947-1:2017(E) ISO 2017 All rights reserved 33.28 nonconforming unit firework (3.15) or a primary pack (3.31) with one or more nonconformities (3.29) 3.29 nonconformity nonfulfilment of a requirement 3.30 preliminary effect visual effect which follows the initial fuse (3.20)

33、burning and precedes the first principal effect (3.16) of a firework (3.15) 3.31 primary pack package of one or more fireworks (3.15) of the same category and type, offered for retail sale as a single unit 3.32 principal effect any of the effects listed in the classification in accordance with ISO 2

34、59472 for the particular type of firework (3.15) 3.33 projected debris fragments projected laterally from the firework while functioning 3.34 propellant charge pyrotechnic composition (3.36) which will burn to evolve gas which, in turn, is intended to propel the firework (3.15) as a whole or to expe

35、l one or more pyrotechnic units (3.37) without bursting the firework case (3.14), and which can also transmit ignition 3.35 protruding fuse initial fuse (3.20) that extends from the firework case (3.14) and is used to ignite the article with a given time delay 3.36 pyrotechnic composition substance

36、or mixture of substances which is designed, on ignition or initiation, to produce an aural and/or visual effect and/or to evolve gas 3.37 pyrotechnic unit discrete unit that is part of a firework (3.15) which, upon functioning, will burn or explode to produce a visual and/or aural effect Note 1 to e

37、ntry: The effect produced by a pyrotechnic unit is normally part of a combination of effects produced by the firework. 3.38 report charge pyrotechnic composition (3.36) which, upon functioning, will produce a report 3.39 rocket launcher tube, frame or base from which a rocket can be launched ISO 259

38、47-1:2017(E) 4 ISO 2017 All rights reserved3.40 selection pack package of fireworks (3.15) of more than one type and/or more than one category, offered for retail sale as a single unit Note 1 to entry: A selection pack can contain primary packs as well as individual fireworks. 3.41 testing point loc

39、ation in the test area where the firework (3.15) is placed at the beginning of a performance test 3.42 total NEC mass of pyrotechnic composition (3.36) in the firework (3.15), including the pyrotechnic composition in the initial fuse (3.20) or transmitting fuses (3.44), friction or ignition heads (3

40、18) 3.43 type test test performed on a sample of products, representative of the production envisaged, in order to demonstrate their compliance with the provisions of ISO 26261 series 3.44 transmitting fuse component of a firework (3.15) which is intended to transmit ignition from one part of a fir

41、ework to another, with or without a delay ISO 25947-1:2017(E) ISO 2017 All rights reserved 5Bibliography 1 ISO 28591:1999, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 2 ISO 26261 (all parts), Fireworks

42、Category 4 ISO 25947-1:2017(E) 6 ISO 2017 All rights reservedAlphabetical index acceptance quality limit AQL 3.1 major nonconforming unit 3.23 batch test 3.2 major nonconformity 3.24 black powder 3.3 minor nonconforming unit 3.25 burning rate of composition 3.4 minor nonconformity 3.26 bursting char

43、ge 3.5 net explosive content NEC 3.27 critical nonconforming unit 3.6 nonconforming unit 3.28 critical nonconformity 3.7 nonconformity 3.29 debris 3.8 preliminary effect 3.30 droop 3.9 primary pack 3.31 effect charge 3.10 principal effect 3.32 end closure 3.11 projected debris 3.33 explosion 3.12 pr

44、opellant charge 3.34 external support 3.13 protruding fuse 3.35 firework case 3.14 pyrotechnic composition 3.36 firework 3.15 pyrotechnic unit 3.37 first principal effect 3.16 report charge 3.38 friction head 3.17 rocket launcher 3.39 ignition head 3.18 selection pack 3.40 initial fuse burning 3.19 testing point 3.41 initial fuse 3.20 total NEC 3.42 invisible burning time 3.21 type test 3.43 invisible burning 3.22 transmitting fuse 3.44 ISO 25947-1:2017(E) ISO 201 7 All rights reserved 7 ISO 25947-1:2017(E) ICS 01.040.71; 71.100.30 Price group A ISO 2017 All rights reserved