ISO 29771 AMD 1-2014 Thermal insulating materials for building applications - Determination of organic content Amendment 1《建筑设施用绝热材料 有机物含量的测定 修改件1》.pdf

1、 ISO 2014 Thermal insulating materials for building applications Determination of organic content AMENDMENT 1 Matriaux isolants thermiques destins aux applications du btiment Dtermination du contenu organique AMENDEMENT 1 INTERNATIONAL STANDARD ISO 29771 First edition 2008-11-01 Reference number ISO

2、 29771:2008/Amd.1:2014(E) AMENDMENT 1 2014-12-01 ISO 29771:2008/Amd.1:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electro

3、nic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. +

4、41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 29771:2008/Amd.1:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Inte

5、rnational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison wi

6、th ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directive

7、s, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some o

8、f the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declaratio

9、ns received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about

10、 ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement m

11、ethods. ISO 2014 All rights reserved iii Thermal insulating materials for building applications Determination of organic content AMENDMENT 1 Replace the existing Introduction with the following. This International Standard comprises the original EN 13820:2003 prepared by Technical Committee CEN/TC 8

12、8, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries. This International Standard is one of a series of documents specifying test methods based on existing European Standards that are being

13、 adopted by ISO. This “package” of standards includes the following group of interrelated documents. ISO standard Title Respective EN standard ISO 12344 Thermal insulating products for building applications Determination of bending behaviour EN 12089 ISO 12968 Thermal insulation products for buildin

14、g applications Determination of the pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) EN 13495 ISO 29465 Thermal insulating products for building applications Determination of length and width EN 822 ISO 29466 Thermal insulating products for building appl

15、ications Determination of thickness EN 823 ISO 29467 Thermal insulating products for building applications Determination of squareness EN 824 ISO 29468 Thermal insulating products for building applications Determination of flatness EN 825 ISO 29469 Thermal insulating products for building applicatio

16、ns Determination of compression behaviour EN 826 ISO 29470 Thermal insulating products for building applications Determination of the apparent density EN 1602 ISO 29471 Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory condi

17、tions (23 degrees C/50 % relative humidity) EN 1603 ISO 29472 Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1604 ISO 29764 Thermal insulating products for building applications Determination of defo

18、rmation under specified compressive load and temperature conditions EN 1605 ISO 29765 Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1607 ISO 29771:2008/Amd.1:2014(E) ISO 2014 All rights reserved 1 ISO 29771:2008/Amd.1:2014(E) ISO st

19、andard Title Respective EN standard ISO 29766 Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1608 ISO 29767 Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 1609 IS

20、O 29768 Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12085 ISO 29769 Thermal insulating products for building applications Determination of behaviour under point load EN 12430 ISO 29770 Thermal insulating products for building applicat

21、ions Determination of thickness for floating-floor insulating products EN 12431 ISO 29771 Thermal insulating materials for building applications Determination of organic content EN 13820 ISO 29803 Thermal insulation products for building applications Determination of the resistance to impact of exte

22、rnal thermal insulation composite systems (ETICS) EN 13497 ISO 29804 Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 ISO 29805 Thermal insulation products for building ap

23、plications Determination of the mechanical properties of glass fibre meshes EN 13496 ISO 16534 Thermal insulating products for building applications Determination of compressive creep EN 1606 ISO 16535 Thermal insulating products for building applications Determination of long-term water absorption

24、by immersion EN 12087 ISO 16536 Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12088 ISO 16537 Thermal insulating products for building applications Determination of shear behaviour EN 12090 ISO 16544 Thermal insulating products for

25、building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12429 ISO 16545 Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13793 ISO 16546 Thermal insulating products for building applicat

26、ions Determination of freezethaw resistance EN 120912 ISO 2014 All rights reserved ISO 29771:2008/Amd.1:2014(E) A further series of existing European Standards on test methods for products used to insulate building equipment and industrial installations was adopted by ISO. This “package” of standard

27、s comprises the following group of interrelated standards: ISO standard Title Respective EN standard ISO 12623 Thermal insulating products for building equipment and industrial installa- tions Determination of short-term water absorption by partial immer- sion of preformed pipe insulation EN 13472 I

28、SO 12624 Thermal insulation products Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13468 ISO 12628 Thermal insulating products for building equipment and industrial installa- tions Determination of dimensions, squareness and linearity of pre-

29、formed pipe insulation EN 13467 ISO 12629 Thermal insulating products for building equipment and industrial instal- lations Determination of water vapour transmission properties of pre- formed pipe insulation EN 13469 ISO 18096 Thermal insulating products for building equipment and industrial instal

30、- lations Determination of maximum service temperature for preformed pipe insulation EN 14707 ISO 18097 Thermal insulating products for building equipment and industrial installa- tions Determination of maximum service temperature EN 14706 ISO 18098 Thermal insulating products for building equipment

31、 and industrial installa- tions Determination of the apparent density of preformed pipe insulation EN 13470 ISO 18099 Thermal insulating products for building equipment and industrial installa- tions Determination of the coefficient of thermal expansion EN 13471 The Application of Agreement on techn

32、ical cooperation between ISO and CEN (Vienna Agreement), Modes 1, 2, 4, and 5 was not approved by CEN/TC 88 and the necessity not seen by its stakeholders. Page 3, 6.2. Add the following second sentence to the existing 4th paragraph: Place the container with the test specimen inside in the desiccato

33、r and allow it to cool down to (23 5) C. In tropical countries, the temperature can be (27 5) C and this shall be stated clearly in the test report. Add the following last sentence to the existing 6th paragraph: Return the container with the test specimen inside to the furnace at a temperature of (5

34、00 20) C or at the temperature specified in the relevant product standard or any other international or European technical specification for at least 30 min. Remove the container from the furnace and place it in the desiccator and allow it to cool down to (23 5) C. In tropical countries, the temperature can be (27 5) C and this shall be stated clearly in the test report. ISO 2014 All rights reserved 3 ISO 29771:2008/Amd.1:2014(E) ISO 2014 All rights reserved IC S 91.100.60 Price based on 3 pages