ISO 3772-2000 Photography - Rolls of sensitized material for the pre-press industry - Dimensions and related requirements《摄影 照相排版用胶卷 尺寸及相关要求》.pdf

1、Reference number ISO 3772:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 3772 Third edition 2000-10-15 Photography Rolls of sensitized material for the pre-press industry Dimensions and related requirements Photographie Rouleaux de matriau sensible pour lindustrie de primpression Dimensions et exigence

2、s connexesISO 3772:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

3、 In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be foun

4、d in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the

5、address given below. ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

6、ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reservedISO 3772:2000(E) ISO 2000 All rights reserved iii Contents

7、 Page Foreword.iv 1 Scope 1 2 Normative references 1 3 Term and definition .1 4 Conditions for measurement of dimensions 1 5 Dimensions.2 5.1 Width of rolls2 5.2 Length of rolls2 5.3 Core internal diameter.2 5.4 Core length.2 5.5 Dimensions of disposable cassettes.2 6 Splices 5 7 Winding configurati

8、on.5 8 Disposable cassette pull-out force 5 9 Package marking .5 10 Compliance.6 Annex A (informative) Dimensional stability 7 Bibliography8ISO 3772:2000(E) iv ISO 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standar

9、ds bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organi

10、zations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in

11、 the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility th

12、at some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 3772 was prepared by Technical Committee ISO/TC 42, Photography. This third edition of ISO 3772 canc

13、els and replaces the second edition (ISO 3772:1991), and ISO 6407:1992, Photography Film dimensions Graphic arts; ISO 6408:1991, Photography Paper dimensions Rolls for photocomposition; and ISO 11313:1994, Photography Disposable cassettes containing photocomposition film and paper Dimensions and rel

14、ated requirements. These have been combined and revised, featuring a new emphasis on general cutting rules as opposed to listing all known sizes specifically. The combination of these International Standards into a single International Standard results in a tightening of specified tolerances for cer

15、tain sizes and applications. This International Standard replaces a number of standards relating to rolls of sensitized material for the pre-press industry. It features a simplified set of rules for dimensioning new sizes. It is hoped that the use of this International Standard will promote the comp

16、atibility of sensitized material and equipment. Annex A of this International Standard is for information only.INTERNATIONAL STANDARD ISO 3772:2000(E) ISO 2000 All rights reserved 1 Photography Rolls of sensitized material for the pre-press industry Dimensions and related requirements 1 Scope This I

17、nternational Standard specifies the dimensions of sensitized materials, cores and disposable cassettes, and describes package marking for sensitized materials, including those for electronic scanners or image-setting devices and those materials supplied in disposable cassettes. It is applicable to p

18、hotographic sensitized materials in rolls for use in the pre-press industry. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or rev

19、isions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the norm

20、ative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 1:1975, Standard reference temperature for industrial length measurements. ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications. 3 Term and defin

21、ition For the purposes of this International Standard, the following term and definition applies. 3.1 pre-press that part of the printing or publishing process preceding preparation of a printing plate NOTE It includes those applications previously defined as graphic arts, image-setting, photocompos

22、ition and scanner output. 4 Conditions for measurement of dimensions The dimensions and tolerances specified in this International Standard apply at the time of manufacture, measured under atmospheric conditions of (23 2) C and (50 5) % relative humidity, as specified in ISO 554. All measuring instr

23、ument calibrations should be conducted at a temperature of 20 C, as specified in ISO 1, and a relative humidity of 50 %.ISO 3772:2000(E) 2 ISO 2000 All rights reserved 5 Dimensions 5.1 Width of rolls It is preferred that cutting sizes conform to the rules given in Table 1. Specific sizes that for hi

24、storical reasons do not conform to these rules are specified in Table 2. 5.2 Length of rolls The preferred length of rolls in disposable cassettes shall be 30 m for film and 45 m for paper. The preferred nominal length of rolls not in cassettes shall be 60 m. Actual useable length at the time of fin

25、ishing shall not be less than the nominal length. Recognized nominal roll lengths are specified in Table 3. 5.3 Core internal diameter The following internal diameters of cores shall be preferred: 50,7 mm 0,3 mm 71,9 mm 0,5 mm The following internal diameters of cores are recognized: 28,8 mm 0,3 mm

26、71,2 mm 0,3 mm 5.4 Core length The core shall not protrude and shall not be recessed by more than 3,0 mm. 5.5 Dimensions of disposable cassettes The cassette dimensions shall conform to the values given in Table 4 and shown in Figure 1. Table 1 Cutting rules for roll widths Dimensions in millimetres

27、 Width of sensitized material Nominal Aim Tolerance Up to and including 150 Nominal minus 0,25 0,25 Greater than 150, up to and including 260 Nominal minus 0,5 0,5 Greater than 260 Nominal minus 0,8 0,8ISO 3772:2000(E) ISO 2000 All rights reserved 3 Table 2 Dimensions for recognized roll widths Widt

28、hs of sensitized materials for pre-press a Nominal cm Aim mm Minimum mm Maximum mm 22,9 228,2 227,8 228,6 30,5 304,0 303,2 304,8 35,6 354,8 354 355,6 45,7 456,4 455,6 457,2 50,8 507,2 506,4 508 71 710,0 709,5 710,5 76,2 761,2 760,4 762 83,8 838,0 837,5 838,5 91,4 913,6 912,8 914,4 94 940,0 939,2 940

29、,8 106,6 1 066,0 1 065,2 1 066,8 111,7 1 117,0 1 116,2 1 117,8 a Originally in inches (see 5.1). Table 3 Recognized roll lengths Nominal length m 10 20 30 30,5 34,5 45 45,7 55 61,0 75 120 122,0ISO 3772:2000(E) 4 ISO 2000 All rights reserved Dimension W shall never be less than dimension E on any sin

30、gle cassette. Dimension M is the width of the sensitized material given in Tables 1 and 2. Dimension Description Minimum mm Maximum mm L Length see Table 4 see Table 4 H Nominal height 94 102 W Nominal width 94 111 E 88 98 Figure 1 Disposable cassette dimensions Table 4 Dimensions for disposable cas

31、settes Dimensions in millimetres Nominal width of sensitized material Minimum cassette length Maximum cassette length Maximum pull-out force N Up to and including 150 Nominal plus 11,5 Nominal plus 33,5 10 Greater than 150 Nominal plus 12,0 Nominal plus 34,0 14ISO 3772:2000(E) ISO 2000 All rights re

32、served 5 6 Splices There shall be no splices in rolls of sensitized materials for the pre-press industry. 7 Winding configuration The overall width of the roll (including any widthwise winding deviations) shall not exceed the nominal width of the sensitized material by more than 2 mm. NOTE Rolls of

33、sensitized materials may be wound with either the sensitized side in or with the sensitized side out. 8 Disposable cassette pull-out force The shape and dimensions of all parts of the cassette and its contents shall be such that the force required to pull the sensitized material out of the cassette,

34、 following initial manual release, shall not exceed the values as given in Table 4, regardless of how much sensitized material remains in the cassette. 9 Package marking Sufficient data shall be provided on a products packaging to inform the user of proper use and handling. Product packaging shall b

35、e marked so as to indicate: product name and size; conditions of use (such as safelight); conditions of shipping and storage. To accomplish this, each of the packages which constitute the products packaging should be marked so as to indicate one or more of the following 1 : product name or tradename

36、; for unit packages, reasonable effort shall be made to make this item legible under recommended safelight conditions; name or trademark of the manufacturer; manufacturers catalogue identification number; bar code information; information to assist recycling of waste packaging; quantity of units con

37、tained in the package; product name or tradename of sensitized material; nominal product dimensions, in metric units, with the smallest dimension first; batch number and/or parent roll number; 1 There may be legal requirements in certain countries for other data to be marked on the package.ISO 3772:

38、2000(E) 6 ISO 2000 All rights reserved expiration date or “develop before” date or inventory control code; manufacturers recommended safelight conditions 2 ; manufacturers recommended storage conditions 2) ; Indication of winding, if applicable 2) . 10 Compliance If it is desired to indicate complia

39、nce of the product with this International Standard, the following wording shall be used: “COMPLYING WITH ISO 3772” 2 This may be indicated by wording or by a code.ISO 3772:2000(E) ISO 2000 All rights reserved 7 Annex A (informative) Dimensional stability The dimensions and tolerances specified appl

40、y at the time of manufacture and when measured in equilibrium with the standard atmosphere specified in ISO 554; i.e. temperature (23 2) C and relative humidity (50 5) %. These dimensions may be altered by permanent ageing shrinkage and by temporary shrinkage and swell, since they will change with t

41、he temperature and the moisture content of the atmosphere. Nevertheless, at the time of package opening within the warrantee period of the sensitized material, dimensions measured under atmospheric conditions of temperature (23 2) C and relative humidity (50 5) % should not depart from those at the

42、time of manufacture by more than 0,05 % greater than the maximum tolerance, or 0,05 % less than the minimum tolerance. Samples of paper cut from a roll require a minimum of 14 days conditioning for resin-coated paper and a minimum of 8 h for non-resin-coated paper as specified in ISO 6221.ISO 3772:2

43、000(E) 8 ISO 2000 All rights reserved Bibliography 1 ISO 6221:1996, Photography Films and papers Determination of dimensional change. 2 ISO 11312, Photography Sheets of sensitized material for the pre-press industry Dimensions and related requirements. 3 ISO 14535, Photography Room-light loading packages for electronic scanner and image-setting film and paper rolls Dimensions and related requirements.ISO 3772:2000(E) ICS 37.040.20 Price based on 8 pages ISO 2000 All rights reserved