ISO 5172 AMD 1-2012 Gas welding equipment - Blowpipes for gas welding heating and cutting - Specifications and tests Amendment 1《气焊设备 气焊、加热和切割用焊枪 规范和试验 修改件1》.pdf

1、 ISO 2012 Gas welding equipment Blowpipes for gas welding, heating and cutting Specifications and tests AMENDMENT 1 Matriel de soudage aux gaz Chalumeaux pour soudage aux gaz, chauffage et coupage Spcifications et essais AMENDEMENT 1 INTERNATIONAL STANDARD ISO 5172 Third edition 2006-04-01 Reference

2、 number ISO 5172:2006/Amd.1:2012(E) AMENDMENT 1 2012-07-15 ISO 5172:2006/Amd.1:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electro

3、nic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org

4、 Web www.iso.org Published in Switzerland ISO 5172:2006/Amd.1:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO techni

5、cal committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely w

6、ith the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Int

7、ernational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document m

8、ay be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 5172:2006 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 8, Equipment for gas welding, cutting and allied processes. R

9、equests for official interpretations of any aspect of this Amendment should be directed to the Secretariat of ISO/TC 44/SC 8 via your national standards body. A complete listing of these bodies can be found at www.iso.org. ISO 2012 All rights reserved iii Gas welding equipment Blowpipes for gas weld

10、ing, heating and cutting Specifications and tests AMENDMENT 1 Page 7, 6.1 Delete the existing text and insert the following. The marking shall be legible and durable and shall be in accordance with 6.2 to 6.7. In the following, the “manufacturer” includes also distributors and suppliers. Page 7, 6.4

11、 Delete the existing text and insert the following. The minimum marking requirements for all nozzles are given in Annex J. Page 26, Clause 10 Delete the existing text and insert the following. The manufacturer shall supply, with each blowpipe, instructions for use, in the language of the country whe

12、re it is sold, covering at least: permissible types of gas; all applicable pressure and flow data; explanation of all the marking; details of the mixing principle; safety devices which are required or recommended; safety warnings; steps to be taken before operation, including leak testing; how to op

13、erate, including lighting-up and shutdown; service, maintenance and repair. The instructions shall also include detailed information on nozzles: the manufacturer shall provide the torch operator with detailed instructions for proper settings of the heating or brazing nozzles; this information shall

14、include the recommended pressure settings in kilopascals and the volume flow rates in litres per minute for the oxygen and fuel gas required these settings should give the operator acceptable performance under normal operating conditions; the manufacturer shall provide safety information for the pro

15、per use and operation of the nozzles and related equipment used for oxyfuel cutting, welding, as well as heating or brazing this information should be in the form of instruction literature or imprinted on the product carton. ISO 5172:2006/Amd.1:2012(E) ISO 2012 All rights reserved 1 ISO 5172:2006/Am

16、d.1:2012(E) Page 38 Delete Annex D. Page 45 Before the Bibliography, insert Annex J. See text overleaf. 2 ISO 2012 All rights reserved ISO 5172:2006/Amd.1:2012(E) Annex J (normative) Uniform designation system for oxyfuel nozzles In the oxyfuel welding and cutting industry, every equipment manufactu

17、rer has its own system for designating the size of oxyfuel nozzles for cutting, welding, as well as heating or brazing. These systems are based on a variety of different nozzle features and in many cases are completely arbitrary. In any case, it is currently impossible to identify a nozzle by model

18、number for a given manufacturer and cross-reference it to a different manufacturer to obtain like performance and size, i.e. there is no consensus among manufacturers on the designation of nozzles which have similar performance and uses. The following system of marking provides a common information

19、base that the operator can rely on to identify nozzle performance from one manufacturer to another. The overall intent of this system is to provide a common identification system that results in the safe operation of oxyfuel nozzles, i.e. operators are informed that they are using the correct nozzle

20、 for the job being performed. Cutting or welding Name, registered trademark or identifying mark of manufacturer Symbol for fuel gas Thickness range of the work piece or code to permit easy reference to the operating data Heating or brazing Name, registered trademark or identifying mark of manufacturer Symbol for fuel gas and oxygen or compressed air Code to permit easy reference to the operating data ISO 2012 All rights reserved 3ISO 5172:2006/Amd.1:2012(E) ISO 2012 All rights reserved ICS 25.160.30 Price based on 3 pages