1、 Reference number ISO 7240-21:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 7240-21 First edition 2005-07-01 Fire detection and alarm systems Part 21: Routing equipment Systmes de dtection et dalarme dincendie Partie 21: quipement de transmission ISO 7240-21:2005(E) PDF disclaimer This PDF file may con
2、tain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsib
3、ility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation pa
4、rameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless other
5、wise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright
6、 office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 7240-21:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope. 1 2 Normative
7、references. 1 3 Definitions. 2 4 General requirements. 3 5 General requirements for indications. 4 6 Quiescent condition. 5 7 Fire alarm condition 5 8 Supervisory signal condition 6 9 Fault warning condition . 6 10 Disabled condition 7 11 Test condition. 8 12 Design requirements 9 13 Additional desi
8、gn requirements for software-controlled routing equipment. 12 14 Marking 13 15 Tests. 14 16 Test report. 23 Annex A (informative) Explanation of access levels 24 Annex B (informative) Design requirements for software-controlled routing equipment 26 ISO 7240-21:2005(E) iv ISO 2005 All rights reserved
9、Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a t
10、echnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters
11、 of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulate
12、d to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible
13、for identifying any or all such patent rights. ISO 7240-21 was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subcommittee SC 3, Fire detection and alarm systems. ISO 7240 consists of the following parts, under the general title Fire detection and alarm s
14、ystems: Part 1: General and definitions Part 2: Control and indicating equipment Part 4: Power supply equipment Part 5: Point-type heat detectors Part 6: Carbon monoxide fire detectors using electro-chemical cells Part 7: Point-type smoke detectors using scattered light, transmitted light or ionizat
15、ion Part 11: Manual call points Part 12: Line type smoke detectors using a transmitting light beam Part 13: Compatibility assessment of system components Part 14: Guidelines for drafting codes of practice for design, installation and use of fire detection and fire alarm systems in and around buildin
16、gs Technical Report Part 15: Multisensor fire detectors Part 21: Routing equipment Part 22: Duct sampling equipment The following part is under preparation: Part 9: Test fire for fire detectors Technical Report ISO 7240-21:2005(E) ISO 2005 All rights reserved v Introduction This part of ISO 7240 com
17、bines the requirements for both fire-alarm routing (transmitting) equipment (ISO 7240-1:, Figure 1, item E) and fault (trouble) warning routing equipment (ISO 7240-1:, Figure 1, item J) into a single equipment Standard. Routing equipment receives signals from control and indicating equipment (ISO 72
18、40-1:, Figure 1, item B) and sends fire alarm signals to a fire-alarm receiving station (ISO 7240-1, Figure 1, item F) and fault signals to a fault warning (trouble signal) receiving station (ISO 7240-1, Figure 1, item K). The receiving stations may be in the same or different locations. This part o
19、f ISO 7240 describes the mandatory functions which are required to be provided on all routing equipment covered by this part of ISO 7240, and optional functions with their associated requirements. It is intended that the options will be used for specific applications, as recommended in application g
20、uidelines. Each optional function is included as a separate entity, with its own set of associated requirements, in order to permit routing equipment covered by this document with different combinations of functions to conform to this part of ISO 7240. Routing equipment complying with this part of I
21、SO 7240 will need to fulfil the requirements of all of the mandatory functions, together with the requirements of those optional functions which are provided. INTERNATIONAL STANDARD ISO 7240-21:2005(E) ISO 2005 All rights reserved 1 Fire detection and alarm systems Part 21: Routing equipment 1 Scope
22、 This part of ISO 7240 specifies requirements, methods of test, and performance criteria for fire-alarm routing (transmitting) equipment (ISO 7240-1:, Figure 1, item E) and for fault (trouble) warning routing equipment (ISO 7240-1:, Figure 1, item J) for use in fire detection and fire alarm systems
23、installed in buildings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IS
24、O 7240-1: 1) , Fire detection and alarm systems Part 1: General and definitions ISO 7240-4, Fire detection and alarm systems Part 4: Power supply equipment IEC 60068-1:1990-05, Environmental testing Part 1: General and guidance IEC 60068-2-1, Environmental testing Part 2: Tests. Tests A: Cold IEC 60
25、068-2-6, Environmental testing Part 2: Tests. Test Fc: vibration (sinusoidal) IEC 60068-2-47, Environmental testing Part 2-47: Test methods Mounting of components, equipment and other articles for vibration, impact and similar dynamic tests IEC 60068-2-75, Environmental testing Part 2-75: Tests. Tes
26、t Eh: Hammer tests IEC 60068-2-78, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60529:2001-02, Degrees of protection provided by enclosures (IP Code) IEC 60721-3-3:2002-10, Classification of environmental conditions Part 3-3: Classifications of groups of environmental
27、 parameters and their severities Stationary use and weatherprotected locations EN 50130-4, Alarm systems Part 4: Electromagnetic compatibility Product family standard: Immunity requirements for components of fire, intruder and social alarm systems 1) To be published. ISO 7240-21:2005(E) 2 ISO 2005 A
28、ll rights reserved3 Definitions For the purposes of this document, the definitions given in ISO 7240-1 and the following apply. 3.1 access level one of several states of a routing equipment in which selected controls can be operated; manual operations can be carried out; indications are visible, and
29、/or; information can be obtained. NOTE See Annex A. 3.2 field sub-division of a window 3.3 functional condition condition of the routing equipment characterized by its indication at the routing equipment NOTE The functional conditions recognized in this part of the ISO 7240 are the following: fire a
30、larm condition, when a fire alarm is indicated; supervisory signal condition, when a supervisory signal is indicated; fault warning condition, when a fault is indicated; disabled condition, when the disablement of functions is indicated; test condition, when the testing of functions is indicated; qu
31、iescent condition, when the routing equipment is powered by a power supply conforming to ISO 7240-4 and no other functional condition is indicated. 3.4 indicator device which can change its state to give information 3.5 indication information given by an indicator 3.6 mandatory adjective qualificati
32、on applied to those functions required to be provided on all routing equipment and the functions requirements and to the requirements of any optional functions that have requirements, if such optional functions are provided 3.7 non-volatile memory memory elements which do not require the presence of
33、 an energy source for the retention of their contents ISO 7240-21:2005(E) ISO 2005 All rights reserved 3 3.8 point component connected to a detection circuit enabling the transmission or reception of information in relation to fire detection NOTE Includes ISO 7240-1:, Figure 1, items A and D. 3.9 pr
34、ogram software necessary for routing equipment to comply with at least the requirements of this part of ISO 7240, including initializing data, reset and interrupt vectors, operating code, and declarations 3.10 reset operation capable of terminating the fire alarm condition and/or the fault warning c
35、ondition 3.11 running data alterable data subject to temporary modification during operation, either automatically or by manual controls 3.12 separate adjective physically separate and exclusively provided for the purpose or purposes stated in this part of ISO 7240 3.13 silencing noun manual operati
36、on for switching off the audible signal of a sounding device that is capable of being automatically re-sounded by a new event 3.14 transmission path connection, external to the cabinet of the routing equipment, for the transmission of information and/or power between the routing equipment and other
37、components of a fire detection and fire alarm system as defined in ISO 7240-1, and/or between parts of routing equipment contained in different cabinets 3.15 volatile memory memory elements which require the presence of an energy source for the retention of their contents 3.16 window part or all of
38、an alphanumeric display used for information relating to one functional condition at a given time NOTE A sub-division of the display might be realized either by mechanical separation, or under software control. 3.17 zone geographical sub-division of the protected premises in which one or more points
39、 are installed and for which a common zonal indication is provided 4 General requirements If functions other than those specified in this part of the ISO 7240 are provided, they shall not jeopardize compliance with any requirements of this part of the ISO 7240. ISO 7240-21:2005(E) 4 ISO 2005 All rig
40、hts reservedIf an optional function is included in the routing equipment, then all the corresponding requirements shall be met. 5 General requirements for indications 5.1 Display of functional conditions 5.1.1 The routing equipment shall be capable of unambiguously indicating the following functiona
41、l conditions, as described in Clauses 6 to 11: quiescent condition; fire alarm condition; supervisory signal condition; fault warning condition; disabled condition; test condition. 5.1.2 The routing equipment shall be capable of being simultaneously, in any combination of the following functional co
42、nditions: fire alarm condition; supervisory signal condition; fault warning condition; disabled condition; test condition. 5.2 Display of indications All mandatory indications shall be clearly identifiable, except where otherwise specified in this part of ISO 7240. 5.3 Indications on alphanumeric di
43、splays Where an alphanumeric display is used to display indications relating to different functional conditions, these may be displayed at the same time. However, for each functional condition there shall be only one window in which all of the fields relating to that functional condition are grouped
44、. 5.4 Indication of the supply of power A visible indication shall be given by means of a separate light-emitting indicator while the routing equipment is supplied with power. 5.5 Additional indications Where indications are used in addition to mandatory indications, these shall not result in contra
45、diction or confusion. ISO 7240-21:2005(E) ISO 2005 All rights reserved 5 6 Quiescent condition Any kind of system information may be displayed during the quiescent condition. However, no indications shall be given which could be confused with control-and-indicating equipment indications used in the
46、fire alarm condition, supervisory signal condition, fault warning condition, disabled condition, test condition. 7 Fire alarm condition 7.1 Reception and processing of fire signals 7.1.1 The routing equipment shall report the fire alarm condition to the fire alarm receiving station (ISO 7240-1:, Fig
47、ure 1, item F) when fire alarm signals are received from the control-and-indicating equipment. 7.1.2 The mandatory indications and/or outputs shall not be falsified by multiple fire signals received from the same or different control-and-indicating equipment, resulting from the simultaneous operatio
48、n of two control-and-indicating equipment and/or the operation of further control-and-indicating equipment. 7.2 Indication of the fire alarm condition 7.2.1 The fire alarm condition shall be indicated when the routing equipment receives the fire alarm signal from the control-and-indicating equipment
49、. 7.2.2 The time taken for processing of signals from control-and-indicating equipment shall not delay the indication of the fire alarm condition at the routing equipment by more than 60 s. 7.2.3 The signal may be indicated by means of a separate light-emitting indicator and/or a field on the alphanumeric display. 7.2.4 The indicator shall flash when the condition is received by the routing equipment and go st
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1