ISO 8115-2-1994 Bales - Part 2 Bales of man-made staple fibres - Dimensions《包 第2部分 人造短纤维包 尺寸》.pdf

1、INTERNATIONAL STANDARD ISO 81152 First edition 1994-09-01 Bales - Part 2: Bales of man-made staple fibres - Dimensions Balles - Partie 2: Balles de fibres chimiques discontinues - Dimensions Reference nun-her ISO 8115-2:1994(E) Copyright International Organization for Standardization Provided by IHS

2、 under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 8115=2:1994(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing Internation

3、al Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO,

4、 also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter

5、national Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 8115-2 was prepared by Technical Committee ISO/TC 72, Textile machinery and allied machinery and accessories, Sub- committee SC 1, Spinning preparatory, spinning and doubling (twistin

6、g) machinery. ISO 8115 consists of the following Parts, under the general title Bales: - Part 2: Bales of man-made staple fibres - Dimensions - Part 3: Bales of cotton - Packaging and designation NOTE 1 ISO 8115:1986 will become Part 1 at the time of its next revision. Annex A of this part of ISO 81

7、15 is for information only. 0 ISO 1994 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronie or mechanical, including photocopying and microfilm, without Permission in writing from the publisher. Internation

8、al Organization for Standardization Case Postale 56 l CH-l 211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATI

9、ONAL STANDARD 0 ISO ISO 8115=2:1994(E) Bales - Part 2: Bales of man-made staple fibres - Dimensions 1 Scope actual bale dimensions. Consideration of this part of ISO 8115 is therefore strongly recommended for all new This patt of ISO 8115 specifies the Overall dimensions of banded bales of man-made

10、staple fibres. The specified dimensions allow for an Optimum utilisation of the loading space of freight Containers and trucks. bale-press installations. 2 Overall dimensions NOTE 2 lt is expected that the implementation of this The Overall dimensions of banded bales of man-made part of ISO 8115 wil

11、l be a long-term process, since bale staple fibres are shown in figure 1 and given in presses presently in Service will preclude a Change in the table 1. 1 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permi

12、tted without license from IHS-,-,-ISO 8115=2:1994(E) Direction of Direc tion of bale pressing bale pressing L = Overall length of the banded bale W = Overall width of the banded bale H = Overall height of the banded bale Figure 1 - Banded bale Table 1 - Overall dimensions Dimensions in millimetres L

13、 0 - 250 W max. H max. 720 820 1 140 720 960 1 140 NOTE 3 For loading into Containers, a length of 1 080 mm is recommended. An example for loading an ISO freight Container of nominal length 6 m is given in tableA.1. Copyright International Organization for Standardization Provided by IHS under licen

14、se with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 8115=2:1994(E) Annex A (informative) Example of loading of an ISO Container An example of loading an ISO series 1 freight Container of nominal length 6 m is given in table A.1. Table A.1 - Example of lo

15、ading 1080x720x1140 30 1 080 x 720 x 960 36 1 080 x 720 820 42 1 080 720 x 720 48 LxWxH Loading capacity mm Number of bales Loading arrangement Dimensions in millimetres 3 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or

16、networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Co

17、pyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 8115=2:1994(E) PCS 59.060.20 Descriptors: textiles, synthetic fibres, bales, dimensions. Price based on 3 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-