ISO 8116-8-1995 Textile machinery and accessories - Beams for winding - Part 8 Definitions of run-out tolerances and methods of measurement《纺织机械与附件 经轴 第8部分 跳动公差.pdf

1、INTERNATIONAL STANDARD ISO 8116-8 First edition 1995-09-15 Textile machinery and accessories - Beams for winding - Part 8: Definitions of run-out tolerantes and methods of measurement Ma Wie/ pour Iindus trie textile - Ensouples pour enroulement - Partie 8: Definition des tolkrances de battement et

2、methodes de mesurage Reference number ISO 8116-8:1995(E) Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 8116=8:1995(E) Foreword ISO (the International Organization f

3、or Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has th

4、e right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft In

5、ternational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 8116-8 was prepared by Technical Committee lSO/TC 72,

6、Textile machinery and allied machinery and accessories, Sub- committee SC 2, Winding and preparatory machinery for fabric manufac- tut-e. This first edition of ISO 8116-8 cancels and replaces ISO 2013:1983, which has been technically revised. ISO 8116 consists of the following Parts, under the gener

7、al title Textile machinery and accessories - Beams for winding: - Part 7: General vocabulary - Part 2: Warpers beams - Part 3: Weavers beams - Part 4: Quality classification of flanges for weavers beams, warpers beams and sectional beams - Part 5: Sectional beams for Warp knitting machines - Part 6:

8、 Beams for ribbon weaving and ribbon knitting - Part 7: Beams for dyeing slivers, rovings and yarns 0 ISO 1995 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronie or mechanical, including photocopying and

9、microfilm, without Permission in writing from the publisher. International Organization for Standardization Case Postale 56 l CH-l 211 Geneve 20 l Switzerland Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reprod

10、uction or networking permitted without license from IHS-,-,-0 ISO ISO 8116=8:1995(E) - Part 8: Definitions of run-out tolerantes and methods of measure- - Part 9: Dyeing beams for textile fabrks Annex A of this part of ISO 8116 is for information only. Copyright International Organization for Standa

11、rdization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networ

12、king permitted without license from IHS-,-,-INTERNATIONAL STANDARD 0 ISO ISO 8116=8:1995(E) Textile machinery and accessories - Beams for winding - Part 8: Definitions of run-out tolerantes and methods of measurement 1 Scope This part of ISO 8116 defines variations of form and Position, i.e. axial c

13、ircular run-out tolerante of f barrel run-out tolerante of beams with and without shafts, and gives the methods of measuring of form and Position. I anges and total such variations The maximum tolerantes together with the recommended limit for residual Unbalance are specified in the Parts of ISO 811

14、6 for each type of beam. 2 Definitions and methods of measurement 2.1 Axial circular run-out tolerante (7”) of flanges (figure 1) Dimensions in millimetres Figure 1 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or network

15、ing permitted without license from IHS-,-,-ISO 8116=8:1995(E) 0 ISO The axial circular run-out tolerante (T,) is the differente between the greatest and the smallest deviation of the inner face of a flange, measured approximately 15 mm from the outer edge of the flange during one complete revolution

16、 of the beam about the axis A-B. 2.2 Total run-out tolerante (T,) of the barrel (figure 2) - the circularity of the barrel; - the radial circular run-out of the beam barrel. In the case of weavers beams with screw threads on the barrel, the flanges shall be positioned at the outer edges of the barre

17、l. The greatest of the observations (readings) shall be taken as the value of the total run-out of the barrel; it shall not exceed the permissible maximum value. Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking

18、 permitted without license from IHS-,-,-ISO 8116=8:1995(E) Annex A (informative) Bibliography 1 ISO 1101: 1983, Technical drawings - Geometrical tolerancing - Tolerancing o f form, orien ta tion, loca tion and run-out - Generalities, definitions, symbols, indications on drawings. Copyright Internati

19、onal Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for Res

20、aleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page inten

21、tionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided b

22、y IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 8116=8:1995(E) ICS 59.120.20 Descriptors: textile machinery, winding, yams, beams (textile machinery), dimensions, dimensional measurements, run-out tolerantes. Price based on 3 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-