ISO 9735-10-2014 Electronic data interchange for administration commerce and transport (EDIFACT) - Application level syntax rules (Syntax version number 4 Synta.pdf

1、 ISO 2014 Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 2) Part 10: Syntax service directories change de donnes informatis pour ladministration, le commerce et le transport (EDIFACT) R

2、gles de syntaxe au niveau de lapplication (numro de version de syntaxe: 4, numro ddition de syntaxe: 2) Partie 10: Annuaires de syntaxe INTERNATIONAL STANDARD ISO 9735-10 Second edition 2014-12-15 Reference number ISO 9735-10:2014(E) ISO 9735-10:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTE

3、CTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Perm

4、ission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 9735-10:2014(E) I

5、SO 2014 All rights reserved iii Contents Page Foreword iv Introduction vi 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 2 4 Conformance . 2 5 Syntax service directories . 2 5.1 Service segment directory 2 5.2 Service composite data element directory 24 5.3 Service simple data eleme

6、nt directory 34 6 Syntax service code list directory 58 Annex A (informative) Snapshot of the syntax service code list directory 59 Bibliography .111 ISO 9735-10:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO memb

7、er bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, government

8、al and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance

9、are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention i

10、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/o

11、r on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity as

12、sessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information ISO 9735-10 was prepared by Technical Committee ISO/TC 154, Processes, data elements and documents in commerce, industry an

13、d administration, in collaboration with UN/CEFACT through the Joint Syntax Working Group. This second edition cancels and replaces the first edition (ISO 9735-10:2002), which has been technically revised. The principle changes are as follows: Annex A has been revised to implement all syntax code rel

14、eases since publication of the first edition; the representation of data element 0536 “Certificate reference” has been amended from “an35” to “an70”. ISO 9735 consists of the following parts 1) , under the general title Electronic data interchange for administration, commerce and transport (EDIFACT)

15、 Application level syntax rules (Syntax version number: 4, Syntax release number: 2) 2) : Part 1: Syntax rules common to all parts Part 2: Syntax rules specific to batch EDI Part 3: Syntax rules specific to interactive EDI Part 4: Syntax and service report message for batch EDI (message type CONTRL)

16、 Part 5: Security rules for batch EDI (authenticity, integrity and non-repudiation of origin) Part 6: Secure authentication and acknowledgement message (message type AUTACK) Part 7: Security rules for batch EDI (confidentiality) 1) Further parts may be added in the future. 2) Publication of this new

17、 edition of ISO 9735-10 means that the syntax release number in the general title is increased from “1” to “2”.iv ISO 2014 All rights reserved ISO 9735-10:2014(E) Part 8: Associated data in EDI Part 9: Security key and certificate management message (message type KEYMAN) Part 10: Syntax service dire

18、ctories ISO 2014 All rights reserved v ISO 9735-10:2014(E) Introduction This part of ISO 9735 includes the rules at the application level for the structuring of data in the interchange of electronic messages in an open environment, based on the requirements of either batch or interactive processing.

19、 These rules have been agreed by the United Nations Economic Commission for Europe (UN/ECE) as syntax rules for Electronic Data Interchange for Administration, Commerce and Transport (EDIFACT) and are part of the United Nations Trade Data Interchange Directory (UNTDID) which also includes both batch

20、 and interactive Message Design Guidelines. This part of ISO 9735 can be used in any application, but messages using these rules can only be referred to as EDIFACT messages if they comply with other guidelines, rules and directories in the UNTDID. For UN/EDIFACT, batch messages comply with the messa

21、ge design rules for batch usage. These rules are maintained in the UNTDID. Communications specifications and protocols are outside the scope of this part of ISO 9735.vi ISO 2014 All rights reserved INTERNATIONAL ST ANDARD ISO 9735-10:2014(E) Electronic data interchange for administration, commerce a

22、nd transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 2) Part 10: Syntax service directories 1 Scope This part of ISO 9735 specifies the syntax service directories of all parts of ISO 9735. 2 Normative references The following documents, in whole or

23、in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9735-1, Electronic data interchange for

24、administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 1: Syntax rules common to all parts ISO 9735-2, Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (S

25、yntax version number: 4, Syntax release number: 1) Part 2: Syntax rules specific to batch EDI ISO 9735-3, Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 3: Syntax rules specific

26、 to interactive EDI ISO 9735-4, Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 4: Syntax and service report message for batch EDI (message type CONTRL) ISO 9735-5, Electronic da

27、ta interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 5: Security rules for batch EDI (authenticity, integrity and non-repudiation of origin) ISO 9735-6, Electronic data interchange for administrat

28、ion, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 6: Secure authentication and acknowledgement message (message type - AUTACK) ISO 9735-7, Electronic data interchange for administration, commerce and transport (EDIFACT) App

29、lication level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 7: Security rules for batch EDI (confidentiality) ISO 9735-8, Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax releas

30、e number: 1) Part 8: Associated data in EDI ISO 9735-9, Electronic data interchange for administration, commerce and transport (EDIFACT) Application level syntax rules (Syntax version number: 4, Syntax release number: 1) Part 9: Security key and certificate management message (message type- KEYMAN)

31、ISO 2014 All rights reserved 1 ISO 9735-10:2014(E) 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 9735-1 apply. 4 Conformance Whereas this part shall use a version number of “4” in the mandatory data element 0002 (Syntax version number), and shal

32、l use a release number of “02” in the conditional data element 0076 (Syntax release number), each of which appear in the segment UNB (Interchange header), interchanges continuing to use the syntax defined in the earlier published versions shall use the following Syntax version numbers, in order to d

33、ifferentiate them from each other and from this part: ISO 9735:1988: Syntax version number: 1 ISO 9735:1988 (amended and reprinted in 1990): Syntax version number: 2 ISO 9735:1988 and ISO 9735:1988/Amd 1:1992: Syntax version number: 3 ISO 9735:1998 (all parts): Syntax version number: 4 Conformance t

34、o a standard means that all of its requirements, including all options, are supported. If all options are not supported, any claim of conformance shall include a statement which identifies those options to which conformance is claimed. Data that is interchanged is in conformance if the structure and

35、 representation of the data conform to the syntax rules specified in this part of ISO 9735. Devices supporting this part of ISO 9735 are in conformance when they are capable of creating and/or interpreting the data structured and represented in conformance with the standard. Conformance to this part

36、 shall include conformance to ISO 9735-1, ISO 9735-2, ISO 9735-3, ISO 9735-4, ISO 9735-5, ISO 9735-6, ISO 9735-7, ISO 9735-8 and ISO 9735-9. When identified in this part of ISO 9735, provisions defined in related standards shall form part of the conformance criteria. 5 Syntax service directories 5.1

37、 Service segment directory 5.1.1 S ervic e segment specification legend Function The function of the segment POS The sequential position number of the stand-alone data element or composite data element in the segment table TAG The tags for all service segments contained in the segment directory shal

38、l start with the letter “U”. The tags of all service composite data elements start with the letter “S”, and the tags of all service simple data elements start with the figure “0”. Name Name of a COMPOSITE DATA ELEMENT in capital letters Name of a STAND-ALONE DATA ELEMENT in capital letters Name of a

39、 component data element in small letters S The status of the stand-alone data element or composite data element in the segment, or of the components in the composite (where M = Mandatory and C = Conditional)2 ISO 2014 All rights reserved ISO 9735-10:2014(E) R The maximum number of occurrences of a s

40、tand-alone data element or composite data element in the segment Repr. Data value representation of the stand-alone data element or component data elements in the composite: a alphabetic characters n numeric characters an alphanumeric characters a3 3 alphabetic characters, fixed length n3 3 numeric

41、characters, fixed length an3 3 alphanumeric characters, fixed length a3 up to 3 alphabetic characters n3 up to 3 numeric characters an3 up to 3 alphanumeric characters 5.1.2 Dependency not e identifiers Code Name D1 One and only one D2 All or none D3 One or more D4 One or none D5 If first, then all

42、D6 If first, then at least one more D7 If first, then none of the others See ISO 9735-1:2002, 11.5, for the definition of the dependency note identifiers. 5.1.3 Index of service segments by tag Change indicators (compared with the previous edition of this part of ISO 9735) a plus sign (+) for an add

43、ition an asterisk (*) for an amendment to structure a hash sign (#) for changes to names a vertical bar (|) for changes to text for descriptions, notes and functions ISO 2014 All rights reserved 3 ISO 9735-10:2014(E) a minus sign (-) for a deletion an X sign (X) for marked for deletion Tag Name UCD

44、Data element error indication UCF Group response UCI Interchange response UCM Message/package response UCS Segment error indication UGH Anti-collision segment group header UGT Anti-collision segment group trailer UIB Interactive interchange header UIH Interactive message header UIR Interactive statu

45、s UIT Interactive message trailer UIZ Interactive interchange trailer UNB Interchange header UNE Group trailer UNG Group header UNH Message header UNO Object header UNP Object trailer UNS Section control UNT Message trailer UNZ Interchange trailer USA Security algorithm USB Secured data identificati

46、on USC Certificate USD Data encryption header USE Security message relation USF Key management function USH Security header USL Security list status4 ISO 2014 All rights reserved ISO 9735-10:2014(E) Tag Name USR Security result UST Security trailer USU Data encryption trailer USX Security references

47、 USY Security on references 5.1.4 Index of service segments by name Change indicators (compared with the previous edition of this part of ISO 9735) a plus sign (+) for an addition an asterisk (*) for an amendment to structure a hash sign (#) for changes to names a vertical bar (|) for changes to tex

48、t for descriptions, notes and functions a minus sign (-) for a deletion an X sign (X) for marked for deletion Tag Name UGH Anti-collision segment group header UGT Anti-collision segment group trailer USC Certificate UCD Data element error indication USD Data encryption header USU Data encryption tra

49、iler UNG Group header UCF Group response UNE Group trailer UIB Interactive interchange header UIZ Interactive interchange trailer UIH Interactive message header UIT Interactive message trailer UIR Interactive status UNB Interchange header UCI Interchange response ISO 2014 All rights reserved 5 ISO 9735-10:2014(E) Tag Name UNZ Interchange trailer USF Key management function UNH Message header UNT Message trailer UCM Message/package response UNO Object h