ISO IEC 13157-2-2016 Information technology - Telecommunications and information exchange between systems - NFC Security - Part 2 NFC-SEC cryptography standard .pdf

1、Information technology Telecommunications and information exchange between systems NFC Security Part 2: NFC-SEC cryptography standard using ECDH and AES Technologies de linformation Tlinformatique Scurit NFC Partie 2: Norme de cryptographie NFC-SEC utilisant ECDH et AES INTERNATIONAL STANDARD ISO/IE

2、C 13157-2 Reference number ISO/IEC 13157-2:2016(E) Second edition 2016-04-01 ISO/IEC 2016 ii ISO/IEC 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized

3、 otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright o

4、ffice Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 13157-2:2016(E)ISO/IEC 13157-2:2016(E) ISO/IEC 2016 All rights reserved iii Contents Page Foreword . v Introduction vi 1 Scope 1 2 Conformance . 1 3 N

5、ormative references 1 4 Terms and definitions . 2 5 Conventions and notations 2 5.1 Concatenation 2 5.2 Hexadecimal numbers 2 6 Acronyms . 2 7 General . 3 8 Protocol Identifier (PID) 3 9 Primitives . 3 9.1 Key agreement . 4 9.1.1 Curve P-192 4 9.1.2 EC Key Pair Generation Primitive 4 9.1.3 EC Public

6、 key validation . 4 9.1.4 ECDH secret value derivation Primitive 4 9.1.5 Random nonces . 4 9.2 Key Derivation Functions . 5 9.2.1 KDF for the SSE . 5 9.2.2 KDF for the SCH 5 9.3 Key Usage 5 9.4 Key Confirmation . 6 9.4.1 Key confirmation tag generation . 6 9.4.2 Key confirmation tag verification 6 9

7、.5 Data Encryption . 6 9.5.1 Initial value of counter (IV) . 6 9.5.2 Encryption 6 9.5.3 Decryption 7 9.6 Data Integrity 7 9.6.1 Protect data integrity. 7 9.6.2 Check data integrity 7 9.7 Message Sequence Integrity 7 10 Data Conversions 7 10.1 Integer-to-Octet-String Conversion . 7 10.2 Octet-String-

8、to-Integer Conversion . 7 10.3 Point-to-Octet-String Conversion 8 10.4 Octet-String-to-Point Conversion 8 11 SSE and SCH service invocation . 8 11.1 Pre-requisites . 9 11.2 Key Agreement 10 11.2.1 Sender (A) Transformation . 10 11.2.2 Recipient (B) Transformation . 10 11.3 Key Derivation . 11 11.3.1

9、 Sender (A) Transformation . 11 ISO/IEC 13157-2:2016(E) iv ISO/IEC 2016 All rights reserved 11.3.2 Recipient (B) Transformation 11 11.4 Key Confirmation 11 11.4.1 Sender (A) Transformation 11 11.4.2 Recipient (B) Transformation 12 12 SCH data exchange 12 12.1 Preparation 13 12.2 Data Exchange 13 12.

10、2.1 Send . 13 12.2.2 Receive 13 Annex A (normative) AES-XCBC-PRF-128 and AES-XCBC-MAC-96 algorithms 15 A.1 AES-XCBC-PRF-128 15 A.2 AES-XCBC-MAC-96. 15 Annex B (normative) Fields sizes . 16 Annex C (informative) Informative references . 17 ISO/IEC 13157-2:2016(E) ISO/IEC 2016 All rights reserved v Fo

11、reword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technica

12、l committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part i

13、n the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

14、al criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject

15、 of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any

16、 trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in t

17、he Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information ISO/IEC 13157-2 was prepared by Ecma International (as ECMA-386) and was adopted, under a special “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel w

18、ith its approval by national bodies of ISO and IEC. This second edition cancels and replaces the first edition (ISO/IEC 13157-2:2010) which has been technically revised. ISO/IEC 13157 consists of the following parts, under the general title Information technology Telecommunications and information e

19、xchange between systems NFC Security: Part 1: NFC-SEC NFCIP-1 security services and protocol Part 2: NFC-SEC cryptography standard using ECDH and AES Part 3: NFC-SEC cryptography standard using ECDH-256 and AES-GCM 1 Part 4: NFC-SEC entity authentication and key agreement using asymmetric cryptograp

20、hy 1 Part 5: NFC-SEC entity authentication and key agreement using symmetric cryptography 1 1To be published. ISO/IEC 13157-2:2016(E) vi ISO/IEC 2016 All rights reserved Introduction The NFC Security series of standards comprise a common services and protocol Standard and NFC- SEC cryptography stand

21、ards. This NFC-SEC cryptography Standard specifies cryptographic mechanisms that use the Elliptic Curves Diffie-Hellman (ECDH) protocol for key agreement and the AES algorithm for data encryption and integrity. This International Standard addresses secure communication of two NFC devices that do not

22、 share any common secret data (“keys“) before they start communicating which each other. This edition ensures to use the latest references to cryptographic standards. INTERNATIONAL STANDARD ISO/IEC 13157-2:2016(E) ISO/IEC 2016 All rights reserved 1 Information technology Telecommunications and infor

23、mation exchange between systems NFC Security Part 2: NFC-SEC cryptography standard using ECDH and AES 1 Scope This International Standard specifies the message contents and the cryptographic methods for PID 01. This International Standard specifies cryptographic mechanisms that use the Elliptic Curv

24、es Diffie-Hellman (ECDH) protocol for key agreement and the AES algorithm for data encryption and integrity. 2 Conformance Conformant implementations employ the security mechanisms specified in this NFC-SEC cryptography Standard (identified by PID 01) and conform to ISO/IEC 13157-1 (ECMA-385). The N

25、FC-SEC security services shall be established through the protocol specified in ISO/IEC 13157-1 (ECMA-385) and the mechanisms specified in this International Standard. 3 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensab

26、le for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 10116, Information technology - Security techniques - Modes of operation for an n-bit block cipher ISO/IEC 1

27、1770-3, Information technology - Security techniques - Key management - Part 3: Mechanisms using asymmetric techniques ISO/IEC 13157-1, Information technology - Telecommunications and information exchange between systems - NFC Security - Part 1: NFC-SEC NFCIP-1 security services and protocol (ECMA-3

28、85) ISO/IEC 15946-1, Information technology - Security techniques - Cryptographic techniques based on elliptic curves - Part 1: General ISO/IEC 18031, Information technology - Security techniques - Random bit generation ISO/IEC 18033-3, Information technology - Security techniques - Encryption algor

29、ithms - Part 3: Block ciphers ISO/IEC 18092, Information technology - Telecommunications and information exchange between systems - Near Field Communication - Interface and Protocol (NFCIP-1) (ECMA-340) IEEE 1363, IEEE Standard Specifications for Public-Key Cryptography ISO/IEC 13157-2:2016(E) 2 ISO

30、/IEC 2016 All rights reserved FIPS 186-4, Digital Signature Standard (DSS) 4 Terms and definitions For the purposes of this International Standard, all terms and definitions from ISO/IEC 13157-1 (ECMA-385) apply. 5 Conventions and notations The conventions and notations of ISO/IEC 13157-1 (ECMA-385)

31、 as well as the following apply in this document unless otherwise stated. 5.1 Concatenation A | B represents the concatenation of the fields A and B: content of A followed by content of B. 5.2 Hexadecimal numbers (XY) denotes a hexadecimal number XY (i.e. with the Radix of 16) and each pair of chara

32、cters is encoded in one octet. 6 Acronyms For the purposes of this International Standard, all acronyms from ISO/IEC 13157-1 (ECMA-385) apply. Additionally, the following acronyms apply. A Sender, as specified in ISO/IEC 13157-1 (ECMA-385) AES Advanced Encryption Standard B Receiver, as specified in

33、 ISO/IEC 13157-1 (ECMA-385) dA Senders private EC key dB Recipients private EC key DataLen Length of the UserData EC Elliptic Curve ECDH Elliptic Curve Diffie-Hellman EncData Encrypted data G The base point on EC IDA Sender nfcid3 IDB Recipient nfcid3 IDR Any Recipient identification number (e.g. ID

34、 B) IDS Any Sender identification number (e.g. ID A) IV Initial Value K Key KDF Key Derivation Function KE Encryption Key KI Integrity Key ISO/IEC 13157-2:2016(E) ISO/IEC 2016 All rights reserved 3 MAC Message Authentication Code MacA /MacB Integrity protection value of Sender/ Recipient MacTagA Key

35、 confirmation tag from Sender MacTagB Key confirmation tag from Recipient MK Master Key NA / NB Nonce generated by Sender/Recipient NAA / NBB Nonce generated by the pair of NFC-SEC entities NonceS Senders nonce NonceR Recipients nonce PK Public Key PKR Recipients Public Key PKS Senders Public Key PR

36、NG Pseudo Random Number Generator QA / QB Compressed EC public key of Sender / Recipient QA / QB Decompressed EC public key of Sender / Recipient RNG Random Number Generator SharedSecret Shared secret UserData NFC-SEC User data z Unsigned integer representation of the Shared Secret Z Octet string re

37、presentation of z The acronyms used in Clauses 9 and 10 not listed above are formal parameters. 7 General This International Standard specifies mechanisms for the Shared Secret Service (SSE) and the Secure Channel Service (SCH) in ISO/IEC 13157-1 (ECMA-385). To enable secure communication between NF

38、C devices that do not share any common secret data (“keys“) before they start communicating with each other, public key cryptography is used to establish a shared secret between these devices, and more specifically the Elliptic Curve Diffie-Hellman key exchange scheme. This shared secret is used to

39、establish the SSE and the SCH. 8 Protocol Identifier (PID) This International Standard shall use the one octet protocol identifier PID with value 1. 9 Primitives This Clause specifies cryptographic primitives. Clauses 11 and 12 specify the actual use of these primitives. Table 1 summarizes the featu

40、res. ISO/IEC 13157-2:2016(E) 4 ISO/IEC 2016 All rights reserved Table 1 Summary of features Supported services SSE (see ISO/IEC 13157-1 (ECMA-385) SCH (see ISO/IEC 13157-1 (ECMA-385) Key agreement ECDH P-192 KDF AES-XCBC-PRF-128 Key confirmation AES-XCBC-MAC-96 Data encryption AES128-CTR IV Init: AE

41、S-XCBC-PRF-128 Data integrity AES-XCBC-MAC-96 Sequence integrity SN (see ISO/IEC 13157-1 (ECMA-385) Encryption order Encryption (9.5) before MAC calculation (9.6) 9.1 Key agreement Peer NFC-SEC entities shall agree on a shared secret using Key agreement mechanism 4 from ISO/IEC 11770-3 and the Ellip

42、tic Curves Diffie-Hellman primitives from IEEE 1363 as further specified below. 9.1.1 Curve P-192 Curve P-192 as specified in FIPS 186-4 shall be used. 9.1.2 EC Key Pair Generation Primitive The private key d shall be obtained from a random or pseudo-random process conforming to ISO/IEC 18031. a) Ob

43、tain the private key, d, from a random or pseudo-random process conforming to ISO/IEC 18031. b) Compute the public key, PK, as a point on EC, PK = dG. 9.1.3 EC Public key validation The EC public key shall be validated as specified in Public Key Validation of ISO/IEC 15946-1. 9.1.4 ECDH secret value

44、 derivation Primitive The ECDH primitive as specified in 7.2.1 ECSVDP-DH of IEEE 1363 shall output the valid shared secret z and invalid otherwise. 9.1.5 Random nonces Each peer NFC-SEC entity should send fresh random nonces with the EC public key of the entity. The nonces are used to provide more e

45、ntropy to the keys derived from the shared secret (z), and to facilitate the EC key pair management. The correct generation of these nonces is under the responsibility of the entity. ISO/IEC 13157-2:2016(E) ISO/IEC 2016 All rights reserved 5 The entity should guarantee that the nonces it generates h

46、ave 96 bits of entropy valid for the duration of the protocol. The nonces used in an NFC-SEC transaction shall be cryptographically uncorrelated with the nonces from a previous transaction. See ISO/IEC 18031 for further recommendations on random number generation. 9.2 Key Derivation Functions Two Ke

47、y Derivation Functions (KDF) are specified; one for the SSE and one for the SCH. The KDFs shall use AES in XCBC-PRF-128 mode as specified in A.1. For the following sections KDF is: KDF (K, S) = AES-XCBC-PRF-128K (S) The random source (nonces + shared secret z obtained from 9.1.4) used for the SCH sh

48、all be different from the random source used for the SSE. 9.2.1 KDF for the SSE The KDF for the SSE is: MKSSE = KDF-SSE (NonceS, NonceR, SharedSecret, IDS, IDR) Detail of the KDF-SSE function: S = (NonceS 063 | NonceR 063) SKEYSEED = KDF (S, SharedSecret) MKSSE = KDF (SKEYSEED, S | IDS | IDR | (01)

49、9.2.2 KDF for the SCH The KDF for the SCH is: MKSCH, KESCH, KISCH = KDF-SCH (NonceS, NonceR, SharedSecret, IDS, IDR) Detail of the KDF-SCH function: S = (NonceS 063 |NonceR 063) SKEYSEED = KDF(S, SharedSecret) MKSCH = KDF (SKEYSEED, S | IDS | IDR | (01) KESCH = KDF (SKEYSEED, MKSCH | S | IDS | IDR | (02) KISCH = KDF (SKEYSEED, KESCH | S | IDS | IDR | (03) 9.3 Key Usage Each derived key MKSCH, KESCH, KISCH a