ISO IEC 17310-2000 Information technology - Telecommunications and information exchange between systems Private integrated Services Network - Mapping functions .pdf

1、Reference number ISO/IEC 17310:2000(E) ISO/IEC 2000 INTERNATIONAL STANDARD ISO/IEC 17310 First edition 2000-09-15 Information technology Telecommunications and information exchange between systems Private Integrated Services Network Mapping functions for the employment of 64 kbit/s circuit mode conn

2、ections with 16 kbit/s sub-multiplexing Technologies de linformation Tlcommunications et change dinformation entre systmes Rseau priv avec intgration de services Fonctions dapplication pour lemploi de connexions en mode circuit de 64 kbits/s avec sous-multiplexage de 16 kbits/sISO/IEC 17310:2000(E)

3、PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,

4、parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relat

5、ive to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IE

6、C 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the

7、 country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO/IEC 2000 All rights reservedISO/IEC 17310:2000(E) ISO/IEC 2000 All rights reserved iii Contents Forewordi

8、v Introduction v 1 Scope1 2 Conformance 1 3 Normative references .1 4 Definitions2 4.1 External definitions 2 4.2 Special definitions2 4.2.1 Channel. .2 4.2.2 End PINX.2 4.2.3 Inter-PINX Connection. .2 4.2.4 Inter-PINX Link .2 4.2.5 Transit PINX 2 5 Abbreviations .2 6 Introduction 2 7 Capabilities a

9、t the Q reference point 3 8 Mapping functions3 8.1 Physical adaptation.3 8.1.1 64 kbit/s Unrestricted Digital Leased Line (D64U) .3 8.2 Mapping Matrix4 8.2.1 Channel allocation4 8.2.2 Bearer Conditioning for the D Q -channel .4 8.2.3 Bearer Conditioning for the U Q -channels4 Annexes A Implementatio

10、n Conformance Statement (ICS) Proforma5 B Bibliography .8 C QSIG Protocol Codepoints .9 D Example figure for Bearer Conditioning of U Q -channels 10ISO/IEC 17310:2000(E) iv ISO/IEC 2000 All rights reserved Foreword ISO (the International Organization for Standardization) and IEC (the International E

11、lectrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of te

12、chnical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. International Standards are drafted in accordance with the rules given in the IS

13、O/IEC Directives, Part 3. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard req

14、uires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Internat

15、ional Standard ISO/IEC 17310 was prepared by ECMA (as ECMA-253) and was adopted, under a special “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC. Annex A forms a normative part of this Interna

16、tional Standard. Annexes B, C and D are for information only.ISO/IEC 17310:2000(E) ISO/IEC 2000 All rights reserved v Introduction This International Standard is one of a series of standards defining mapping functions in exchanges of Private Integrated Services Networks. The series uses the ISDN con

17、cepts as developed by ITU-T (formerly CCITT) and is also within the framework of standards for open systems interconnection as defined by ISO/IEC. This International Standard specifies mapping functions for the type of scenario where two PINXs are interconnected via a 64 kbit/s circuit mode connecti

18、on with 16 kbit/s sub-multiplexing. This International Standard is based upon the practical experience of ECMA member companies and the results of their active and continuous participation in the work of ISO/IEC JTC 1, ITU-T, ETSI and other international and national standardization bodies. It repre

19、sents a pragmatic and widely based consensus.INTERNATIONAL STANDARD ISO/IEC 17310:2000(E) ISO/IEC 2000 All rights reserved 1 Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Mapping functions for the employment of 64 kbit/s

20、circuit mode connections with 16 kbit/s sub-multiplexing 1S c o p e This International Standard defines the mapping functions in exchanges of Private Integrated Services Networks (PISNs) required for the utilization of scenarios in which 64 kbit/s circuit mode connections are sub-multiplexed into 4

21、x 16 kbit/s channels for carrying inter-PINX signalling and user information. NOTE 1 - This International Standard has been prepared to meet the specific needs of an application for a particular user organisation. However, it may also be applicable elsewhere. The requirements contained in this Inter

22、national Standard will be incorporated in any future standard specifying a more generic approach to bearer conditioning. In order to connect a Private Integrated Services Network Exchange (PINX) to another PINX, mapping functions are required to adapt the specific interfaces at the C reference point

23、 to the application at the Q reference point. As such, mapping functions provide for physical adaptation to the interface at the C reference point. Mapping functions also provide for the mapping of user channels and signalling information at the Q reference point to the appropriate channels or times

24、lots at the C reference point. The C and Q reference points are defined in ISO/IEC 11579-1. The type of interface at the C reference point covered by this International Standard is the 64 kbit/s Unrestricted Digital Leased Line (D64U) Terminal Equipment Interface, in accordance with ITU-T Rec. G.703

25、 At the Q reference point the mapping provides a 16 kbit/s service for user channels to support the transfer of unrestricted digital information and to support the transfer of speech, and a packet mode service for the signalling channel. The applied mapping is a static mapping, i.e. there is a fixe

26、d relationship between user and signalling channels at the Q reference point and the interface at the C reference point. Management functions relating to failure management are outside the scope of this International Standard. This International Standard is applicable to PINXs that can be interconne

27、cted to form a Private Integrated Services Network (PISN) and that support signalling protocols at the Q reference point. 2 Conformance In order to conform to this International Standard, a PINX shall satisfy the requirements identified in the Implementation Conformance Statement (ICS) proforma in a

28、nnex A. 3 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties t

29、o agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain r

30、egisters of currently valid International Standards. ISO/IEC 11579-1:1994, Information technology Telecommunications and information exchange between systems Private Integrated Services Network Part 1: Reference configuration for PISN exchanges (PINX). ITU-T Rec. G.703:1998, Physical / electrical ch

31、aracteristics of hierarchical digital interfaces. ITU-T Rec. Q.920:1993, Digital Subscriber Signalling System No. 1 (DSS1) ISDN user-network interface data link layer General aspects. ITU-T Rec. Q.920 Am. 1:2000, Amendment 1 to ITU-T Recommendation Q.920. ITU-T Rec. Q.921:1997, ISDN user-network int

32、erface Data link layer specification.ISO/IEC 17310:2000(E) 2 ISO/IEC 2000 All rights reserved ITU-T Rec. Q.921 Am. 1:2000, Amendment 1 to ITU-T Recommendation Q.921. ITU-T Rec. I.112:1993, Vocabulary of terms for ISDNs. ITU-T Rec. I.460:1999, Multiplexing, rate adaption and support of existing inter

33、faces. NOTE 2 - This International Standard also contains informative references. Details of these publications are given in annex B. 4 Definitions 4.1 External definitions For the purposes of this International Standard, the following external definitions apply. Integrated Services Digital Network

34、CCITT Rec. I.112) Private Integrated Services Network (ISO/IEC 11579-1) Private Integrated Services Network Exchange (ISO/IEC 11579-1) 4.2 Special definitions 4.2.1 Channel : A means of bi-directional transmission of user or signalling information between two points. 4.2.1.1 D Q -Channel : A channe

35、l used to convey call control information between the Q reference points of two peer PINXs. 4.2.1.2 U Q -Channel : A channel used to convey user information between the Q reference points of two PINXs. 4.2.2 End PINX : In the context of a particular call, a PINX to which one of the users is attached

36、 (Originating PINX or Terminating PINX) or a PINX at which signalling interworking occurs (Gateway PINX). 4.2.3 Inter-PINX Connection : A connection provided by an IVN between two C reference points used to transport inter- PINX information from the PISN control plane and/or the PISN user plane. 4.2

37、4 Inter-PINX Link : A link between the Q reference points of two PINXs, comprising the totality of signalling transfer and user information transfer means. 4.2.5 Transit PINX : In the context of a particular call, any PINX, excluding the End PINXs, through which the call passes. 5 Abbreviations ICS

38、 Implementation Conformance Statement IPC Inter-PINX Connection IPL Inter-PINX Link ISDN Integrated Services Digital Network LD-CELP Low-Delay Code Excited Linear Prediction MP MaPping functional grouping PINX Private Integrated Services Network Exchange PISN Private Integrated Services Network 6 In

39、troduction This International Standard specifies mapping functions for the following scenario: Dedicated 64 kbit/s circuit mode connection with 16 kbit/s sub-multiplexing. This scenario consists of a dedicated 64 kbit/s circuit mode connection in a point-to-point configuration, and offering at the C

40、 reference point an interface with a single 64 kbit/s channel. This 64 kbit/s channel is sub-multiplexed by the Mapping (MP) functional grouping into 4 x 16 kbit/s channels. Where such a channel is used for carrying speech, a speech compression function is also provided.ISO/IEC 17310:2000(E) ISO/IEC

41、 2000 All rights reserved 3 The applied mapping is a static mapping. There is a fixed relationship between user and signalling channels at the Q reference point and the interface at the C reference point. Administrative actions to apply the mapping are necessary at both sides of an IPL. At the C ref

42、erence point more than one instance of the interface type may exist. NOTE 3 - For more information refer to ECMA TR/76 clause 7. 7 Capabilities at the Q reference point For each instance of the Q reference point: 3 user channels (U Q ); and 1 signalling channel (D Q ) for carrying the inter-PINX lay

43、er 3 signalling protocol are provided. The user channels are numbered 13. For a U Q -channel the following bearer capabilities shall be provided: information transfer rate: 16 kbit/s information transfer capability: speech, or unrestricted digital information user information layer 1 protocol: ITU-T

44、 Rec. G.728 16 kbit/s LD-CELP Other attributes shall be the same as at the C reference point. NOTE 4 - The user information layer 1 protocol is only specified as “LD-CELP“ for the case where the information transfer capability is “speech“. In the case where the information transfer capability is “un

45、restricted digital information“, no user information layer 1 protocol is specified; it is an end-to-end matter between terminal equipments attached to a PISN. NOTE 5 - Annex C (informative) specifies the codepoints to be used by the QSIG protocol when implementing the mapping arrangements specified

46、in this International Standard. For a D Q -channel the following bearer capability shall be provided: Transfer mode: packet mode Information transfer capability: unrestricted digital information Information transfer rate: 16 kbit/s Other attributes shall be the same as at the C reference point. The

47、functions to map D Q and U Q channels to an inter-PINX connection (IPC) at the C reference point are described in clause 8. 8 Mapping functions The PINX mapping functions shall meet the following requirements. 8.1 Physical adaptation A PINX shall support the following physical adaptation: 8.1.1 64 k

48、bit/s Unrestricted Digital Leased Line (D64U) Layer 1 termination shall be in accordance with the requirements of co-directional interfaces at 64 kbit/s, specified in ITU-T Rec. G.703. NOTE 6 - ETS 300 290 provides additional information about this interface type. At the C reference point, the inter

49、face described in this clause provides for one IPC with the following bearer capability: Information transfer mode: circuit mode Information transfer capability: unrestricted digital information Information transfer rate: 64 kbit/s.ISO/IEC 17310:2000(E) 4 ISO/IEC 2000 All rights reserved The physical adaptation part of the mapping function shall maintain a fixed relationship between a 64 kbit/s IPC and the 16 kbit/s channels perceived at the Q reference point, according to the require