ISO IEC 19369-2014 Information technology - Telecommunications and information exchange between systems - NFCIP-2 test methods《信息技术 系统间电信和信息交换 NFCIP-2测试方法》.pdf

1、Information technology Telecommunications and information exchange between systems NFCIP-2 test methods Technologies de linformation Tlinformatique Mthodes dessai NFCIP-2 ISO/IEC 2014 INTERNATIONAL STANDARD ISO/IEC 19369 First edition 2014-08-15 Reference number ISO/IEC 19369:2014(E) ISO/IEC 19369:2

2、014(E)ii ISO/IEC 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the in

3、ternet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org W

4、eb www.iso.org Published in Switzerland ISO/IEC 19369:2014(E) ISO/IEC 2014 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Conformance . 1 3 Normative references 1 4 Acronyms 2 5 Test environment and apparatus 2 6 Tests . 3 6.1 Test External RF Field detection 3 6.2 Te

5、st Mode selection and switching 3 ISO/IEC 19369:2014(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in t

6、he development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-g

7、overnmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/

8、IEC Directives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility tha

9、t some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of p

10、atent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as i

11、nformation about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information ISO/IEC 19369 was prepared by Ecma International (as ECMA-403) and was adopted, under a special “fast-track procedure”, by Joint Technical Commit

12、tee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC.iv ISO/IEC 2014 All rights reserved ISO/IEC 19369:2014(E) Introduction This International Standard specifies test methods for ISO/IEC 21481 in addition to those specified in the referenced stan

13、dards. ISO/IEC 2014 All rights reserved v Information technology Telecommunications and information exchange between systems NFCIP-2 test methods 1 Scope This International Standard specifies requirements to verify NFCIP-2 mode selection and initial communication in the selected modes. The Test Mana

14、gement Service Data Units and the interface over which they are exchanged are out of scope. 2 Conformance Conforming implementations pass the tests in Clause 6 using the test environment and apparatus as specified in Clause 5. 3 Normative references The following documents, in whole or in part, are

15、normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 9646, Information technology Open Systems Interco

16、nnection Conformance testing methodology and framework ISO/IEC 10373-6, Identification cards Test methods Part 6: Proximity cards ISO/IEC 10373-7, Identification cards Test methods Part 7: Vicinity cards ISO/IEC 14443-3, Identification cards Contactless integrated circuit cards Proximity cards Part

17、3: Initialization and anticollision ISO/IEC 18092:2013, Information technology Telecommunications and information exchange between systems Near Field Communication Interface and Protocol (NFCIP-1) (also published by Ecma as Standard ECMA-340) ISO/IEC 21481:2012, Information technology Telecommunicat

18、ions and information exchange between systems Near Field Communication Interface and Protocol -2 (NFCIP-2) (also published by Ecma as Standard ECMA-352) ISO/IEC 22536:2013, Information technology Telecommunications and information exchange between systems Near Field Communication Interface and Proto

19、col (NFCIP-1) RF interface test methods (also published by Ecma as Standard ECMA-356) ISO/IEC 23917:2005, Information technology Telecommunications and information exchange between systems NFCIP-1 Protocol Test Methods (also published by Ecma as Standard ECMA-362) INTERNATIONAL ST ANDARD ISO/IEC 193

20、69:2014(E) ISO/IEC 2014 All rights reserved 1 ISO/IEC 19369:2014(E) 4 Acronyms IUT Implementation Under Test LT Lower Tester TB-PDU Transmission Block Protocol Data Unit TM-SDU Test Management Service Data Unit UT Upper Tester 5 Test environment and apparatus The concepts and abstract model of ISO/I

21、EC 9646 are used to verify the operation of an IUT compliant to ISO/IEC 21481. NFCIP-2 test apparatus consists of an Upper Tester (UT) and a Lower Tester (LT) as illustrated in Figure 1. To communicate with the IUT, e.g. to select modes on the IUT, the UT and IUT exchange TM-SDUs. The SDU definition

22、 and the interface between UT and IUT are out of scope of this International Standard. The NFCIP-2 test apparatus implements the specified modes at its LT interface according to the requirements of the test scenarios specified in Clause 6. Implementation Under Test (IUT) Upper Tester (UT) Lower Test

23、er (LT) VICC emulation PICC emulation PCD emulation NFC emulation NFCIP-2 Test Apparatus TB-PDUs TB-SDUs Figure 1 Test configuration2 ISO/IEC 2014 All rights reserved ISO/IEC 19369:2014(E) 6 Tests 6.1 Test External RF Field detection To verify that the IUT does not switch on its RF field, configure

24、the LT as test circuit and perform the test in 8 of ISO/IEC 21481 while using the term NFCIP-2 device instead of NFCIP-1 device. 6.2 Test Mode selection and switching 6.2.1 Test PICC mode a) Select PICC mode on the IUT and place it into the operating volume of the LT b) Select PCD mode on the LT, an

25、d let the LT send REQA of ISO/IEC 14443-3, 1) If the IUT answers with ATQA of ISO/IEC 14443-3 within 1 ms and passes the PICC tests specified in ISO/IEC 10373-6, it passes the test, otherwise 2) Let the LT send REQB of ISO/IEC 14443-3: if the IUT answers with ATQB of ISO/IEC 14443-3 within 1 ms and

26、passes the PICC tests specified in ISO/IEC 10373-6, it passes the test otherwise it fails the test NOTE The 1 ms limit accommodates NFCIP-2 implementations that alternate between Type A and Type B. 6.2.2 Test NFC mode, Target and Initiator a) For NFC, VCD and PCD mode selected on the IUT, place it i

27、n the operating volume of the LT and let the LT switch its RF field off for at least 5,1 ms, and select Initiator for Active communication mode, on either fc/128, fc/64 or fc/32 on the LT, and let the LT send ATR_REQ of ISO/IEC 18092 (see 8.5.1 of ISO/IEC 23917). b) To test step 3 of Clause 7 of ISO

28、/IEC 21481, verify that the IUT responds with ATR_RES of ISO/IEC 18092 for all three selected modes. c) The LT shall switch off its RF field and select NFC mode, Passive communication mode, as a Target on the LT. d) Select NFC mode on the IUT and verify that the IUT executes one of the Initiator pro

29、tocols for fc/128, fc/64 or fc/32 of ISO/IEC 18092 as selected (see 9 of ISO/IEC 23917). 6.2.3 Test PCD mode Use ISO/IEC 10373-6 to verify that the IUT operates in PCD mode with the LT as PICC mode emulator. 6.2.4 Test VCD mode Use ISO/IEC 10373-7 to verify that the IUT operates in VCD mode with the LT as VICC mode emulator. ISO/IEC 2014 All rights reserved 3 ISO/IEC 19369:2014(E) ISO/IEC 2014 All rights reserved ICS 35.100.10 Price based on 3 pages