DIN EN 1028-2-2008 Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 2 Verification of general and safety requirements(includes Amendment.pdf

1、 y!“ # # $ %23%*8* 444342 “% % it has been determined that the standard complies with the requirements of 2006/42/EC. Therefore, CEN/TC 192 decided in June 2007 to use the “simple amendment” (type 1) procedure which does not involve any technical modifications, but only a few minor editorial changes

2、 (e.g. updating the Foreword) and the addition of a new Annex ZB. Amendment A1:2008 thus concretizes in conjunction with EN 1028-2:2002 the basic requirements set out in Annex I of the EU Machinery Directive 98/37/EC (valid until 28 December 2009) and the new Machinery Directive 2006/42/EC which bec

3、omes applicable on 29 December 2009 relating to machines to be placed on the EEA market, with the intent of simplifying the means of proving conformity with such. Once this standard is designated a harmonized standard in the Official Journal of the European Union, a manufacturer applying this new co

4、nsolidated version of the standard may assume compliance with the requirements of the Machinery Directive (the so-called “presumption of conformity”). A revision of Part 1 of EN 1028 (EN 1028-1:2002) was also necessary for the same reasons. This European Standard is to be applied in conjunction with

5、 Part 1 of EN 1028 Classification General and safety requirements. The 2002 edition of this European Standard, together with EN 1028-1, replaced the German standards specifying requirements for and the testing of pumps for fire-brigades, DIN 14420-1:1986-02 and DIN 14420-2:1989-04. Because these two

6、 national standards had to be withdrawn upon the publication of the European Standards, a “residual standard” was published as DIN 14420 containing national provisions not covered by the European Standard but which are necessary for the application of DIN EN 1028 in Germany. The DIN collective mark

7、may be applied to pumps complying with this standard if they have been registered by DIN CERTCO. NOTE 1 Use of the collective mark requires registration by DIN CERTCO Gesellschaft fr Konformittsbewertung mbH, Alboinstr. 56, 12103 Berlin. NOTE 2 is a registered trademark of DIN. DIN EN 1028-2:2008-06

8、 3 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN EN 1028-2:2002-11 as follows: a) Amendment A1:2008 has b

9、een incorporated, i.e. the informative Annex ZB has been added which describes the relationship between the European Standard and the essential requirements of the Machinery Directive 2006/42/EC, and minor editorial changes have been made. Previous editions DIN FEN 103 = DIN 14581: 1935-10 DIN 14420

10、: 1957-08, 1961-06 DIN 14420-1: 1979-08, 1986-02 DIN 14420-2: 1979-08, 1981-09, 1986-08, 1989-04 DIN EN 1028-2: 2002-11 DIN EN 1028-2:2008-06 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1028-2:2002+A1 April 2008 ICS 13.220.10 Supersedes EN 1028-2:2002 Engl

11、ish Version Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 2: Verification of general and safety requirements Pompes usage incendie - Pompes centrifuges avec dispositif damorage destines la lutte contre les incendies - Partie 2: Vrification des prescriptions gnrales et de s

12、curit Feuerlschpumpen - Feuerlschkreiselpumpen mit Entlftungseinrichtung - Teil 2: Feststellung der bereinstimmung mit den allgemeinen und Sicherheitsanforderungen This European Standard was approved by CEN on 5 April 2002 and includes Amendment 1 approved by CEN on 21 February 2008. CEN members are

13、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

14、he CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same

15、 status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

16、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reser

17、ved worldwide for CEN national Members. Ref. No. EN 1028-2:2002+A1:2008: EEN 1028-2:2002+A1:2008 (E) Contents Foreword3 0 Introduction 4 1 Scope.4 2 Normative references 4 3 Terms and definitions5 4 Verifications5 4.1 General5 4.2 Type verification.5 4.3 Individual verification 5 4.4 Methods of veri

18、fication6 4.4.1 Calculation check.6 4.4.2 Design check 6 4.4.3 Compliance verification (manufacturing check).6 4.5 Measuring instruments7 5 Verification of the safety requirements and/or protective measures .8 6 Verification of the general and performance requirements.11 7 Test report 14 Annex A (no

19、rmative) Suction line for tests15 Annex B (normative) Pressure measurements .18 Annex C (normative) Measurements of delivery rates .19 Annex D (normative) Dry suction test 20 Annex E (normative) Performance test22 Annex F (normative) Working test24 Annex G (normative) Pressure test 25 Annex H (norma

20、tive) Efficiency test.26 Annex I (normative) Primer test 28 Annex J (normative) Cold test29 Annex K (informative) Guidance for acceptance tests on delivery.30 Annex ZA (informative) ! ! ! !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC .31 Annex Z

21、B (informative) ! ! ! !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC .32 Bibliography 33 Page 2 DINEN10282:200806EN 1028-2:2002+A1:2008 (E) Foreword This document (EN 1028-2:2002+A1:2008) has been prepared by Technical Committee CEN/TC 192 “Fir

22、e service equipment“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by

23、October 2008. This document supersedes EN 1028-2:2002. This document includes Amendment 1, approved by CEN on 2008-02-21. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. This document has been prepared under a mandate given to CEN by the European

24、Commission and the European Free Trade Association and supports essential requirements of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document.“ This part of this European Standard shall be applied only in conjunction wit

25、h !EN 1028-1:2002+A1“ “Classification - General and safety requirements“. This part of this European Standard includes the verification of general and safety requirements of fire- fighting centrifugal pumps with primer. EN 1028 “Fire-fighting pumps Fire-fighting centrifugal pumps with primer“ compri

26、ses two parts: Part 1: Classification - General and safety requirements; Part 2: Verification of general and safety requirements. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,

27、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 3 DINEN10282:

28、200806EN 1028-2:2002+A1:2008 (E) 0 Introduction This European Standard is a type C standard as stated in EN 1070. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this standard. Where provisions of this type C standard

29、 are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built in accordance with the provisions of this type C standard. This Standard has been pre

30、pared as a harmonized standard to provide one means of conformity with essential requirements of the Machinery Directive and associated EFTA Regulations. 1 Scope This European Standard covers verification of the general and safety requirements of fire-fighting centrifugal pumps with primer as specif

31、ied in clauses 7 and 8 of !EN 1028-1:2002+A1:2008“. NOTE The tests can also be applied to pumps with nominal delivery rates greater than 6 000 l/min. This standard does not apply to verification related to installation. This standard does not apply to fire-fighting centrifugal pumps with primer that

32、 are manufactured before the date of publication by CEN of this standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are

33、 listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments).

34、EN 837-3, Pressure gauges Part 3: Diaphragm and capsule pressure gauges Dimensions, metrology, requirements and testing. !EN 1028-1:2002+A1:2008“, Fire-fighting pumps Fire-fighting centrifugal pumps with primer Part 1: Classification General and safety requirements. EN 1070, Safety of machinery Term

35、inology. EN 1092-1, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part 1: Steel flanges. EN ISO 1127, Stainless steel tubes Dimensions, tolerances and conventional masses per unit length. 4 DINEN10282:200806EN 1028-2:2002+A1:2008 (E) 3 Terms and

36、 definitions For the purposes of this European Standard, the terms and definitions given in EN 1070 and !EN 1028-1:2002+A1“ apply. 4 Verifications 4.1 General Safety and performance requirements of clauses 5 and 6 of !EN 1028-1:2002+A1:2008“ shall be verified according to Tables 2 and 3. All hydraul

37、ic tests shall be carried out using water having a temperature between 0 C and 20 C. During one test cycle, the water temperature shall not deviate by more than 3 C within this temperature range. The geodetic suction height shall not deviate by more than 5 cm during one test cycle. In order to avoid

38、 air entrainment, the test configuration shall be as shown in Figure A.1 in annex A. If the safety equipment has to be disconnected to carry out any test, the manufacturer shall give information regarding the disconnected safety equipment (e.g. compensating or alternative safety measures to be used

39、during the test and re-connection instructions after completing the test). Verification shall be carried out with the pump equipment assembled for normal intended use. Accessories and covers may be fitted or not, but the effect in either case shall not obscure the validity of the test. Where the pum

40、p is assembled on site, the part of the verifications that cannot be made before dispatch shall be carried out at the place of use in accordance with the installation instructions of the pump manufacturer. For testing purposes, the fire-fighting centrifugal pump shall be presented in its full operat

41、ional configuration. The pump shall be equipped to undergo the full range of tests required. For pumps without a driving motor, a drive flange shall be provided for testing. NOTE 1 If dimensions, mass, or other factors make particular tests on complete equipment impractical, tests can be carried out

42、 on subassemblies or components provided that the results can be verified as representative of the fully assembled equipment. NOTE 2 A guidance for acceptance tests on delivery is given in the informative annex K. The verification regime covers the following basic verifications which applies in clau

43、ses 5 and 6. 4.2 Type verification Ensure that each type of the pump meets the requirements of this standard. NOTE This verification is indicated as “TYP“ in Tables 2 and 3. 4.3 Individual verification Ensure that each pump put on the market meets the requirements of this standard before dispatch. NOTE This verification is indicated as “IND“ in Tables 2 and 3. 5 DINEN10282:200806