EN 16236-2018 Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production Control.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production ControlBS EN 16236:2018Incorporating corrigendum August 2018EUROPEAN STANDARD NORME EUROPENNE EUROPI

2、SCHE NORM EN 16236 July 2018 ICS 91.100.15 English Version Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and Factory Production Control Evaluation et Vrification de la Constance des Performances (EVCP) des granulats - Essais de types et Matrise de la

3、 production en usine Bewertung der Konformitt von Gesteinskrnungen - Erstprfung und werkseigene Produktionskontrolle This European Standard was approved by CEN on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E

4、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official vers

5、ions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

6、 Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, S

7、weden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide

8、 for CEN national Members. Ref. No. EN 16236:2018 ENational forewordThis British Standard is the UK implementation of EN 16236:2018. It supersedes BS EN 16236:2013, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/502/6, Test methods.A list of organiz

9、ations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018I

10、SBN 978 0 539 02123 3ICS 91.100.15Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2018.Amendments/corrigenda issued since publicationDate Text affected3

11、1 August 2018 Correction to supersession details in National ForewordBRITISH STANDARDBS EN 16236:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16236 July 2018 ICS 91.100.15 English Version Assessment and Verification of the Constancy of Performance (AVCP) of aggregates - Type testing and

12、Factory Production Control Evaluation et Vrification de la Constance des Performances (EVCP) des granulats - Essais de types et Matrise de la production en usine Bewertung der Konformitt von Gesteinskrnungen - Erstprfung und werkseigene Produktionskontrolle This European Standard was approved by CEN

13、 on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards m

14、ay be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified

15、 to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icelan

16、d, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC

17、 Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16236:2018 EBS EN 16236:2018EN 16236:2018 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative

18、 references 5 3 Terms and definitions . 7 4 Assessment and Verification of Constancy of Performance - AVCP 9 4.1 General 9 4.2 Type testing . 9 4.2.1 General 9 4.2.2 Test samples, testing and conformity criteria 9 4.2.3 Test reports 10 4.2.4 Shared other party results 10 4.3 Factory Production Contr

19、ol (FPC) 10 4.3.1 General . 10 4.3.2 Procedure 11 4.3.3 Product specific FPC 15 4.3.4 Initial inspection of production unit and of FPC . 16 4.3.5 Continuous surveillance of FPC . 16 4.3.6 Procedure for modifications 17 5 Minimum test frequencies and conformity criteria 17 Bibliography . 34 BS EN 162

20、36:2018EN 16236:2018 (E) 3 European foreword This document (EN 16236:2018) has been prepared by Technical Committee CEN/TC 154 “Aggregates”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or

21、 by endorsement, at the latest by January 2019, and conflicting national standards shall be withdrawn at the latest by April 2020. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or

22、all such patent rights. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This European Standard is intended for use with future revisions (currently in preparation) of the standards listed below. It is not for u

23、se with the versions of these standards dated 2002 (plus amendment A1). EN 12620, Aggregates for concrete; EN 13043, Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas; EN 13139, Aggregates for mortar; EN 13242, Aggregates for unbound and hydrau

24、lic bound materials for use in civil engineering work and road construction; EN 13383-1, Armourstone Part 1: Specification; EN 13450, Aggregates for railway ballast. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implem

25、ent this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

26、Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16236:2018EN 16236:2018 (E) 4 Introduction This European Standard has been written as the system for the Assessment and Verification of the Constancy of Performance (AVCP) of aggregates. This European Standa

27、rd is intended for use with future revisions (currently in preparation) of the standards listed below. It is not for use with the versions of these standards dated 2002 (plus amendment A1). It is intended to be used in conjunction with the future aggregate product standards: EN 12620, EN 13043, EN 1

28、3139, EN 13242, EN 13383-1 and EN 13450 and will be called up by these standards. This European Standard and the corresponding product standards have been written under the Construction Products Regulation (CPR). According to Annex ZA of these standards, the tasks relative to AVCP for the manufactur

29、er comprise Type Testing (TT) and Factory Production Control (FPC). This standard has been compiled from the TT and FPC clauses, annexes and tables previously found in the aggregate product standards. A further revision of this standard is currently under preparation, which will provide more detaile

30、d TT procedures and clear, detailed procedures for product conformity (e.g. statistical conformity criteria, number of samples, tolerances, time limits of validity, etc). The type testing and factory production control procedures are designed to be applied to European Standards for aggregates. When

31、the appropriate “conformity” clauses are applied, it forms part of the system of assessment and verification of constancy of performance as required by the Construction Products Regulation. It provides the minimum provisions for TT and FPC for CE Marking. The testing procedures, using the reference

32、test methods, have the function of providing assurance that a particular aggregate product conforms to each of the selected specified characteristics in the product standard. The type testing procedure is designed to be applied to all harmonized elements of European Harmonized Standards for aggregat

33、es. The factory production control system describes control of the sourcing and processing of the aggregate combined with routine sampling and testing to provide ongoing assurance that the aggregates product continues to conform to those characteristics determined through TT. Testing within FPC may

34、use either the standard reference tests called up by the aggregate product standards or other test procedures which have been shown to correlate with those tests. For commercial and/or contractual reasons, the manufacturer can choose to perform more testing and inspection than the minimum specified.

35、 BS EN 16236:2018EN 16236:2018 (E) 5 1 Scope This European Standard specifies both type testing and factory production control procedures for use during the assessment and verification of constancy of performance of aggregates. Additional testing carried out within contracts is beyond the scope of t

36、his standard. This European Standard is applicable to European Standards for aggregates if regulatory marking of conformity is to be applied. It is also applicable to European Standards for aggregates where regulatory marking does not apply. This European Standard is applicable to the type testing a

37、nd factory production control of aggregates within the scope of EN 12620, EN 13043, EN 13242, EN 13139, EN 13383-1 and EN 13450. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refer

38、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-2, Method of testing cement Part 2: Chemical analysis of cement EN 196-6, Methods of testing cement Part 6: Determination of fineness EN 459-2, Buil

39、ding lime Part 2: Test methods EN 932-1, Tests for general properties of aggregates Part 1: Methods for sampling EN 932-3, Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description EN 932-5, Tests for general properties of aggregates Part 5:

40、 Common equipment and calibration EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution - Sieving method EN 933-3, Tests for geometrical properties of aggregates Part 3: Determination of particle shape Flakiness index EN 933-4, Tests for geometr

41、ical properties of aggregates Part 4: Determination of particle shape Shape index EN 933-5, Tests for geometrical properties of aggregates Part 5: Determination of percentage of crushed and broken surfaces in coarse aggregate particles EN 933-6, Tests for geometrical properties of aggregates Part 6:

42、 Assessment of surface characteristics Flow coefficient of aggregates EN 933-7, Tests for geometrical properties of aggregates Part 7: Determination of shell content Percentage of shells in coarse aggregates EN 933-8, Tests for geometrical properties of aggregates Part 8: Assessment of fines Sand eq

43、uivalent test BS EN 16236:2018EN 16236:2018 (E) 6 EN 933-9, Tests for geometrical properties of aggregates Part 9: Assessment of fines Methylene blue test EN 933-10, Tests for geometrical properties of aggregates Part 10: Assessment of fines Grading of filler aggregates (air jet sieving) EN 933-11,

44、Tests for geometrical properties of aggregates Part 11: Classification test for the constituents of coarse recycled aggregate EN 1097-1, Tests for mechanical and physical properties of aggregates Part 1: Determination of the resistance to wear (micro-Deval) EN 1097-2, Tests for mechanical and physic

45、al properties of aggregates Part 2: Methods for the determination of resistance to fragmentation EN 1097-3:1998, Tests for mechanical and physical properties of aggregates Part 3: Determination of loose bulk density and voids EN 1097-4, Tests for mechanical and physical properties of aggregates Part

46、 4: Determination of the voids of dry compacted filler EN 1097-5, Tests for mechanical and physical properties of aggregates Part 5: Determination of the water content by drying in a ventilated oven EN 1097-6, Tests for mechanical and physical properties of aggregates Part 6: Determination of partic

47、le density and water absorption EN 1097-7, Tests for mechanical and physical properties of aggregates Part 7: Determination of the particle density of filler Pyknometer method EN 1097-8:2009, Tests for mechanical and physical properties of aggregates Part 8: Determination of the polished stone value

48、 EN 1097-9, Tests for mechanical and physical properties of aggregates Part 9: Determination of the resistance to wear by abrasion from studded tyres Nordic test EN 1097-10, Tests for mechanical and physical properties of aggregates Part 10: Determination of water suction height EN 1367-1, Tests for

49、 thermal and weathering properties of aggregates Part 1: Determination of resistance to freezing and thawing EN 1367-2, Tests for thermal and weathering properties of aggregates Part 2: Magnesium sulfate test EN 1367-3, Tests for thermal and weathering properties of aggregates Part 3 : Boiling test for “Sonnenbrand basalt“ EN 1367-4, Tests for thermal and weathering properties of aggregates Part 4: Determination of drying shrinkage EN 1367-5, Tests for thermal and weathering properties