EN 2119-2017 Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Solution treated and precipitation treated - Wires for rivets - 2 mm D 10 mm.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Solution treated and precipitation treated - Wires for rivets - 2 mm D 10 mm - Rm 960 MPaBS EN 2119:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

2、 NORM EN 2119 December 2017 ICS 49.025.05 English Version Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Solution treated and precipitation treated - Wires for rivets - 2 mm D 10 mm - Rm 960 MPa Srie arospatiale - Acier rsistant chaud FE-PA2601 (X6NiCrTiMoV26-15) - Mis en sol

3、ution et prcipit - Fils pour rivets - 2 mm D 10 mm - Rm 960 MPa Luft- und Raumfahrt - Hochwarmfeste Legierung FE-PA2601 (X6NiCrTiMoV26-15) - Lsungsgeglht und ausgehrtet - Drahte fr Niete - 2 mm D 10 mm - Rm 960 MPa This European Standard was approved by CEN on 11 September 2017. CEN members are boun

4、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CE

5、N-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre h

6、as the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L

7、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B

8、-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2119:2017 ENational forewordThis British Standard is the UK implementation of EN 2119:2017.The UK participation in its preparation was entrusted to Technical Commi

9、ttee ACE/61/-/48, Heat Resisting Alloys for Aerospace Purposes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.

10、 The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 98674 1ICS 49.025.05Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on

11、 31 January 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 2119:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2119 December 2017 ICS 49.025.05 English Version Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Solution treate

12、d and precipitation treated - Wires for rivets - 2 mm D 10 mm - Rm 960 MPa Srie arospatiale - Acier rsistant chaud FE-PA2601 (X6NiCrTiMoV26-15) - Mis en solution et prcipit - Fils pour rivets - 2 mm D 10 mm - Rm 960 MPa Luft- und Raumfahrt - Hochwarmfeste Legierung FE-PA2601 (X6NiCrTiMoV26-15) - Lsu

13、ngsgeglht und ausgehrtet - Drahte fr Niete - 2 mm D 10 mm - Rm 960 MPa This European Standard was approved by CEN on 11 September 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

14、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

15、in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

16、 Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United King

17、dom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2119:20

18、17 EBS EN 2119:2017EN 2119:2017 (E) 2 Contents Page European foreword 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Requirements . 5 BS EN 2119:2017EN 2119:2017 (E) 3 European foreword This document (EN 2119:2017) has been prepared by the Aerospace and Defence Industries Association of Europ

19、e - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Stand

20、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2018 and conflicting national standards shall be withdrawn at the latest by June 2018. Attention is drawn to the possibility that some of the elements of this doc

21、ument may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgi

22、um, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

23、 Switzerland, Turkey and the United Kingdom. BS EN 2119:2017EN 2119:2017 (E) 4 Introduction This European Standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This European Standard has been prep

24、ared in accordance with EN 4500-003. BS EN 2119:2017EN 2119:2017 (E) 5 1 Scope This European Standard specifies the requirements relating to: Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) Solution treated and precipitation treated Wires for rivets 2 mm D 10 mm Rm 960 MPa for aerospace applicatio

25、ns. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

26、mendments) applies. EN 2043, Aerospace series Metallic materials General requirements for semi-finished product qualification (excluding forgings and castings) EN 3238, Aerospace series Metallic materials Test method Shear test for wires and rivets EN 4258, Aerospace series Metallic materials Genera

27、l organization of standardization Links between types of EN standards and their use EN 4500-003, Aerospace series Metallic materials Rules for drafting and presentation of material standards Part 003: Specific rules for heat resisting alloys EN 4700-002, Aerospace series Steel and heat resisting all

28、oys Wrought products Technical specification Part 002: Bar and section EN 4700-004, Aerospace series Steel and heat resisting alloys Wrought products Technical specification Part 004: Wire 3 Requirements See Table 1. BS EN 2119:2017EN 2119:2017 (E) 6 Table 1 Requirements for heat resisting alloy FE-

29、PA2601 1 Material designation Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) 2 Chemical Composition % Element C Si Mn P S Al B Cr Mo Ni Ti V Pb Fe min. 30 * 13,5 1,00 24,0 1,90 0,10 Base max. 0,080 1,00 2,00 0,020 0,015 0,35 100 * 16,0 1,50 27,0 2,30 0,50 20 * 3 Method of melting Consumable elect

30、rode remelted 4.1 Form Wire 4.2 Method of production 4.3 Limit dimension(s) mm 2 D 10 5 Technical specification EN 4700-004 6.1 Delivery condition Solution treated Heat treatment 900 C 930 C a/t 15 min/OQ or WQ 6.2 Delivery condition code W 7 Use condition Solution treated and precipitation treated

31、Heat treatment Delivery condition + 680 C 780 C/t 30 min/AC Characteristics 8.1 Test sample(s) See EN 4700-002. 8.2 Test piece(s) See EN 4700-002. 8.3 Heat treatment Delivery condition Use condition 9 Dimensions concerned mm 2 D 10 2 D 10 10 Thickness of cladding on each face % 11 Direction of test

32、piece See EN 4700-004. See EN 4700-004. 12 T Temperature C Ambient Ambient 13 Proof stress Rp0,2 MPa 14 Strength Rm MPa 720 960 15 Elongation A % 16 Reduction of area Z % 17 Hardness 205 HV 260 HV 18 Shear strength Rc MPa 550 Rc 650 b19 Bending k 20 Impact strength 21 C Temperature C 22 Time h 23 St

33、ress a MPa 24 Elongation a % 25 Rupture stress R MPa 26 Elongation at rupture A % 27 Notes (see line 98) *, a, bBS EN 2119:2017EN 2119:2017 (E) 7 34 Grain size See EN 4700-004. 2 One per batch 3 L and LT 7 G 5 - No duplex structure 36 Reverse torsion test for wires See EN 4700-004. 7 6 turns in each

34、 direction 37 Bending of wires (Reverse bend) See EN 4700-004. 7 5 times without failure 44 External defects External imperfections See EN 4700-004. 1 Only visual testing is required 95 Marking inspection See EN 4700-004. 96 Dimensional inspection See EN 4700-004. 98 Notes *p.p.m. aHeat treatment at

35、 = 980 C 10 C may be used by agreement between manufacturer and purchaser. bSee EN 3238. 99 Typical use BS EN 2119:2017EN 2119:2017 (E) 8 100 Product qualification See EN 2043. Qualification programme to be agreed between manufacturer and purchaser. BS EN 2119:2017This page deliberately left blankTh

36、is page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.Bri

37、tish Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and

38、refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting

39、our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need inte

40、rnational and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity

41、 that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other pers

42、on. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is license

43、d to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only

44、. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document,

45、or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription servi

46、ces are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshe

47、d daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Mem

48、bers. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Revision