EN IEC 60317-74-2018 Specifications for particular types of winding wires - Part 74 Polyesterimide enamelled rectangular aluminium wire class 180.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Specifications for particular types of winding wiresPart 74: Polyesterimide enamelled rectangular aluminium wire, class 180 (IEC 60317-74:2018)BS EN IEC 60317-74:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

2、IEC 60317-74 April 2018 ICS 29.060.10 English Version Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180 (IEC 60317-74:2018) Spcifications pour types particuliers de fils de bobinage - Partie 74: Fil de section rectangulaire

3、 maill en aluminium revtu de polyesterimide, de classe 180 (IEC 60317-74:2018) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 74: Flachdrhte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 180 (IEC 60317-74:2018) This European Standard was approved by CENELEC on 2018-0

4、4-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obt

5、ained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified

6、to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greec

7、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation

8、 Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60317-74:2018 E National forewordThis B

9、ritish Standard is the UK implementation of EN IEC 6031774:2018. It is identical to IEC 6031774:2018.The UK participation in its preparation was entrusted to Technical Committee L/99, Miscellaneous Standards Electrical.A list of organizations represented on this committee can be obtained on request

10、to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96289 9ICS 29.060.10Compliance with a British Stan

11、dard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 6031774:2018EUROPEAN STANDARD NORME EU

12、ROPENNE EUROPISCHE NORM EN IEC 60317-74 April 2018 ICS 29.060.10 English Version Specifications for particular types of winding wires - Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180 (IEC 60317-74:2018) Spcifications pour types particuliers de fils de bobinage - Partie 74: F

13、il de section rectangulaire maill en aluminium revtu de polyesterimide, de classe 180 (IEC 60317-74:2018) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 74: Flachdrhte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 180 (IEC 60317-74:2018) This European Standard was ap

14、proved by CENELEC on 2018-04-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na

15、tional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its

16、 own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedo

17、nia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Com

18、it Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60317-74:201

19、8 E BS EN IEC 6031774:2018EN IEC 60317-74:2018 (E) 2 European foreword The text of document 55/1635/FDIS, future edition 1 of IEC 60317-74, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60317-74:2018. The following dates are fi

20、xed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-01-03 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-04-03 Attention is drawn to the

21、 possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-74:2018 was approved by CENELEC as a European Standard

22、 without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 series NOTE Harmonized as EN 60264 series. IEC 60317 series NOTE Harmonized as EN 60317 series. IEC 60851 series NOTE Harmonized as EN 60851 series. BS EN

23、 IEC 6031774:2018EN IEC 60317-74:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this docu

24、ment. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. N

25、OTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60317-0-9 2015 Specifications for particular types of winding wires - Part 0-9: General requirements - Enamelled rectangular alu

26、minium wire EN 60317-0-9 2015 BS EN IEC 6031774:2018 2 IEC 60317-74:2018 IEC 2018 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms, definitions, general notes and appearance . 6 3.1 Terms and definitions 6 3.2 General notes . 7 3.2.1 Methods of test 7 3.2.2 Winding w

27、ire 7 3.3 Appearance 7 4 Dimensions 7 5 Electrical resistance 7 6 Elongation . 7 7 Springiness . 7 8 Flexibility and adherence . 7 9 Heat shock 7 10 Cut-through . 7 11 Resistance to abrasion 7 12 Resistance to solvents . 8 13 Breakdown voltage 8 14 Continuity of insulation 8 15 Temperature index 8 1

28、6 Resistance to refrigerants 8 17 Solderability 8 18 Heat or solvent bonding . 8 19 Dielectric dissipation factor 8 20 Resistance to transformer oil . 8 21 Loss of mass . 8 23 Pin hole test 8 30 Packaging . 8 Bibliography 9 BS EN IEC 6031774:2018IEC 60317-74:2018 IEC 2018 3 INTERNATIONAL ELECTROTECH

29、NICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical com

30、mittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technic

31、al Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmenta

32、l and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agre

33、ements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

34、and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promot

35、e international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicat

36、ed in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) A

37、ll users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage

38、or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publica

39、tion. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such

40、 patent rights. International Standard IEC 60317-74 has been prepared by IEC technical committee 55: Winding wires. The text of this International Standard is based on the following documents: FDIS Report on voting 55/1635/FDIS 55/1640/RVD Full information on the voting for the approval of this Inte

41、rnational Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. BS EN IEC 6031774:2018 4 IEC 60317-74:2018 IEC 2018 A list of all parts in the IEC 60317, published under the general title Specific

42、ations for particular types of winding wires, can be found on the IEC website. The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. The committee has decided that the

43、contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN IEC 6031774:20

44、18IEC 60317-74:2018 IEC 2018 5 INTRODUCTION This part of IEC 60317 forms an element of a series of standards which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851 series); 2) Specifications for par

45、ticular types of winding wires (IEC 60317 series); 3) Packaging of winding wires (IEC 60264 series). BS EN IEC 6031774:2018 6 IEC 60317-74:2018 IEC 2018 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 74: Polyesterimide enamelled rectangular aluminium wire, class 180 1 Scope This part of I

46、EC 60317 specifies the requirements of enamelled rectangular aluminium winding wire of class 180 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin

47、is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor dimensions covered by this standard is: width: min. 2,0 mm max. 16,0 mm; thickness: min. 0,80 mm max. 5,60 mm. Wires of gra

48、de 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified width/thickness ratio are given in IEC 60317-0-9:2015. 2 Normative references The following documents are referred to in the t

49、ext in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-9:2015, Specifications for particular types of winding wires Part 0-9: General requirements Enamelled rectangular aluminium wire 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions For the p