EN IEC 62610-2-2018 Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 s.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 seriesPart 2: Method for the determination of forced air cooling structureBS EN

2、IEC 626102:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 62610-2 July 2018 ICS 31.240 English Version Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 2: Method for the determinatio

3、n of forced air cooling (IEC 62610-2:2018) Structures mcaniques pour quipements lectriques et lectroniques - Gestion thermique pour les armoires conformes aux sries IEC 60297 ET IEC 60917 - Partie 2: Mthode pour la dtermination du refroidissement par ventilation force (IEC 62610-2:2018) Mechanische

4、Bauweisen fr elektrische und elektronische Einrichtungen - Wrmemanagement fr Schrnke nach den Reihen IEC 60297 und IEC 60917 - Teil 2: Verfahren zur Bestimmung der Zwangskhlungsstruktur (IEC 62610-2:2018) This European Standard was approved by CENELEC on 2018-06-20. CENELEC members are bound to comp

5、ly with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

6、 Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre ha

7、s the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La

8、tvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee f

9、r Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 62610-2:2018 E National forewordThis British Standard is the UK implementation

10、 of EN IEC 626102:2018. It is identical to IEC 626102:2018.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on req

11、uest to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 95200 5ICS 31.240Compliance with a British St

12、andard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 626102:2018EUROPEAN STANDARD NORME EU

13、ROPENNE EUROPISCHE NORM EN IEC 62610-2 July 2018 ICS 31.240 English Version Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 2: Method for the determination of forced air cooling (IEC 62610-2:2018

14、) Structures mcaniques pour quipements lectriques et lectroniques - Gestion thermique pour les armoires conformes aux sries IEC 60297 ET IEC 60917 - Partie 2: Mthode pour la dtermination du refroidissement par ventilation force (IEC 62610-2:2018) Mechanische Bauweisen fr elektrische und elektronisch

15、e Einrichtungen - Wrmemanagement fr Schrnke nach den Reihen IEC 60297 und IEC 60917 - Teil 2: Verfahren zur Bestimmung der Zwangskhlungsstruktur (IEC 62610-2:2018) This European Standard was approved by CENELEC on 2018-06-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulati

16、ons which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC memb

17、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official version

18、s. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the N

19、etherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC M

20、anagement Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 62610-2:2018 E BS EN IEC 626102:2018EN IEC 62610-2:2018 2 European foreword The text of document 48D/664/FDIS, future e

21、dition 1 of IEC 62610-2, prepared by SC 48D “Mechanical structures for electrical and electronic equipment“ of IEC/TC 48 “Electrical connectors and mechanical structures for electrical and electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 62610-2:

22、2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-03-20 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021

23、-06-20 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62610-2:2018 was approved by

24、 CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60297-3-100 NOTE Harmonized as EN 60297-3-100. IEC 60297-3-101 NOTE Harmonized as EN 60297-3-101. IEC 60917-2-1 NOTE Harmonized a

25、s EN 60917-2-1. IEC 60917-2-2 NOTE Harmonized as EN 60917-2-2. IEC 62610-5 NOTE Harmonized as EN 62610-5. BS EN IEC 626102:2018EN IEC 62610-2:2018 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are refe

26、rred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International

27、 Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60917-1 - Modular order

28、 for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard EN 60917-1 - BS EN IEC 626102:2018 2 IEC 62610-2:2018 IEC 2018 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions 6 4 Thermal conditions 7 4.1 Ba

29、seline thermal conditions 7 4.2 Reference temperature . 7 4.3 Syntax of surfaces of a generic subrack, chassis or cabinet 8 4.4 Preferred airflow conditions 9 4.5 Cabinet airflow volume and temperature rise management . 10 5 Forced air thermal flow chart for cabinet equipment . 11 5.1 General . 11 5

30、.2 Evaluation of the actual thermal performance of subrack or chassis 12 5.3 Cabinet airflow considerations 12 5.4 Arrangement of subracks and/or chassis-based equipment within the cabinet . 12 5.5 Selection of cabinet mounted forced air cooling device(s) . 13 5.6 Thermal operating environment . 13

31、5.7 Arrangement of cabinets in a server room and preferred airflow 15 Annex A (informative) General method of thermal design for electronic equipment 16 A.1 Thermal resistance and thermal network model 16 A.1.1 Thermal resistance 16 A.1.2 Thermal network model . 16 Bibliography 19 Figure 1 Syntax of

32、 surfaces of a forced air cooled generic subrack or chassis to be mounted into a cabinet 8 Figure 2 Syntax of surfaces of a forced air cooled generic cabinet . 9 Figure 3 Preferred cabinet airflow patterns. 10 Figure 4 Airflow volume management 11 Figure 5 Forced air thermal flow chart for cabinet e

33、quipment . 12 Figure 6 Thermal operating environment (cabinet sectional side view) . 14 Figure 7 Cabinet operating temperature range . 15 Figure 8 Example of cabinet airflows in an aisle containment server room . 15 Figure A.1 Thermal network model for a plug-in unit in subrack or chassis . 18 Table

34、 1 Preferred airflow pattern 9 BS EN IEC 626102:2018IEC 62610-2:2018 IEC 2018 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MECHANICAL STRUCTURES FOR ELECTRICAL AND ELECTRONIC EQUIPMENT THERMAL MANAGEMENT FOR CABINETS IN ACCORDANCE WITH IEC 60297 AND IEC 60917 SERIES Part 2: Method for the determina

35、tion of forced air cooling FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concer

36、ning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their

37、 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates clo

38、sely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relev

39、ant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the t

40、echnical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum

41、extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies prov

42、ide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or

43、its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expense

44、s arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attenti

45、on is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62610-2 has been prepared by subcommittee 48D: Mechanical structures for e

46、lectrical and electronic equipment, of IEC technical committee 48: Electrical connectors and mechanical structures for electrical and electronic equipment. The text of this International Standard is based on the following documents: FDIS Report on voting 48D/664/FDIS 48D/673/RVD Full information on

47、the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. BS EN IEC 626102:2018 4 IEC 62610-2:2018 IEC 2018 This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62610 serie

48、s, published under the general title Mechanical structures for electrical and electronic equipment Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged un

49、til the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a