EN ISO 20557-1-2018 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1 Designation system and basis for specifications.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materialsPart 1: Designation system and basis for specificationsBS EN ISO 205571:2018National forewordThis British Standard is the UK implementation of EN IS

2、O 205571:2018. It is identical to ISO 205571:2018. It supersedes BS EN ISO 289411:2008, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be obtained on request to

3、its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 91250 4ICS 83.080.20Compliance with a British Standar

4、d cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 205571:2018EUROPEAN STANDARDNORME EUROPENNE

5、EUROPISCHE NORMEN ISO 20557-1July 2018ICS 83.080.20 Supersedes EN ISO 289411:2008EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN ISO 205571:2018: EAll rights of exp

6、loitation in any form and by any means reserved worldwide for CEN national MembersPlastics Poly(phenylene ether) (PPE) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 205571:2018)Plastiques Matriaux base de poly(phnylne ther) (PPE) pour moulage et extrus

7、ion Partie 1: Systme de dsignation et base de spcification (ISO 20557-1:2018)Kunststoffe Polyphenylenether (PPE)Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 20557-1:2018)This European Standard was approved by CEN on 9 June 2018.CEN members are bound to comply with the CEN/

8、CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre

9、or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the off

10、icial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

11、 Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 20557-1:2018 (E)European forewordThis document (EN ISO 205571:2018) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technica

12、l Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall be withdrawn at the

13、 latest by January 2019.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN ISO 289411:2008.According to the CENCENELEC Intern

14、al Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ire

15、land, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 205571:2018 has been approved by CEN as EN ISO 205571:2018 without any modificati

16、on.iiBS EN ISO 205571:2018ISO 20557-1:2018Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 24 Designation system 24.1 General . 24.2 Data block 1 . 24.3 Data block 2 . 34.4 Data block 3 . 34.5 Data block 4 . 44.5.1 General 44.5.2 Temperature of deflection under load 44.5.3 Mel

17、t volume-flow rate . 64.5.4 Charpy notched impact strength 64.5.5 Flammability . 64.6 Data block 5 . 65 Examples of designations 75.1 Designation only 75.2 Designation transformed into a specification 9 ISO 2018 All rights reserved iiiContents PageBS EN ISO 205571:2018ISO 20557-1:2018ForewordISO (th

18、e International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committ

19、ee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechn

20、ical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted i

21、n accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

22、Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute a

23、n endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the fol

24、lowing URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.This first edition of ISO 20557-1 cancels and replaces ISO 28941-1:2008, which has been technically revised to introduce a new designation syste

25、m.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 289411. If the existing ISO 289411would be replaced by the new designation system, these documents would refer to the incorrect designation system.The new designation system according to ISO

26、 205571 is intended to replace gradually any designation system according to ISO 289411.A list of all parts in the ISO 20557 series can be found on the ISO website.iv ISO 2018 All rights reservedBS EN ISO 205571:2018Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials Part 1: Desi

27、gnation system and basis for specifications1 ScopeThis document establishes a system of designation for poly(phenylene ether) (PPE) thermoplastic materials, which can be used as the basis for specifications.The types of poly(phenylene ether) (PPE) materials are differentiated from each other by a cl

28、assification system based on appropriate levels of the designatory properties:a) temperature of deflection under load;b) melt volume-flow rate;c) Charpy notched impact strength;d) flammability;and on information about basic polymer parameters, intended application and/or method of processing, import

29、ant properties, additives, colorants, fillers and reinforcing materials.This document is applicable to all PPE materials, including those modified with polystyrene or polyamide or other materials.It applies to materials ready for normal use in the form of powder, granules or pellets and to materials

30、 unmodified or modified by colorants, additives, fillers, etc.It is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which can be required to spec

31、ify a material for a particular application and/or method of processing. If such additional properties are required, they are intended to be determined in accordance with the test methods specified in ISO 20557-2, if suitable.In order to specify a thermoplastic material for a particular application

32、or to ensure reproducible processing, the requirements are given in data block 5 (see 4.1).2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited

33、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 10431, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 205572, Plastics Poly(phenylene ether) (PPE) moulding and extrusion materia

34、ls Part 2: Preparation of test specimens and determination of propertiesINTERNATIONAL STANDARD ISO 20557-1:2018 ISO 2018 All rights reserved 1BS EN ISO 205571:2018ISO 20557-1:20183 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases

35、 for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at https:/www.iso.org/obp4 Designation system4.1 GeneralThe designation system for thermoplastics is based on the following standardized pattern:

36、DesignationDescription block (optional)International Standard number blockIdentity blockIndividual-item blockData block 1Data block 2Data block 3Data block 4Data block 5The designation consists of an optional description block, reading “Thermoplastics”, an identity block comprising the International

37、 Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Identification of the plastic by its symbol PPE in accordance with ISO 1043-1 and information about the composition

38、 of the polymer (see 4.2). Data block 2: Fillers or reinforcing materials and their nominal content (see 4.3). Data block 3: Position 1: intended application or method of processing (see 4.4).Positions 2 to 8: important properties, additives and supplementary information (see 4.4). Data block 4: Des

39、ignatory properties (see 4.5). Data block 5: For the purposes of specifications, a fifth data block may be added containing additional information (see 4.6).The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas.If a data bloc

40、k is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).4.2 Data block 1In this data block, after the hyphen, poly(phenylene ether) materials are identified by the symbol PPE, in accordance with ISO 10431, followed by a hyphen and a codenumber giving additional

41、 information on the polymer, as specified in Table 1.Table 1 Code-numbers used for additional information in data block 1Code-number Material1 PPE2 PPE+PS2 ISO 2018 All rights reservedBS EN ISO 205571:2018ISO 20557-1:2018Code-number Material3 PPE+PA4 PPE+another polymer not already given in this tab

42、le5 PPE+PS+another polymer not already given in this table6 PPE+PP7 PPE+PPS4.3 Data block 2In this data block, the type of filler and/or reinforcing material is represented by a single code-letter in position 1 and its physical form by a second code-letter in position 2, the code-letters being as sp

43、ecified in Table 2. Subsequently (without a space), the mass content may be given by a two-figure number in positions 3 and 4.Table 2 Code-letters for fillers and reinforcing materials in data block 2Code-letter Material Code-letter FormB Boron B Beads, spheres, ballsC Carbon C Chips, cuttingsD Powd

44、erE Clay F FibreG Glass G GroundH WhiskersK Calcium carbonate K Knitted fabricL ex. celluloseaL LayerM Minerala,b, metalaM Mat (thick)N Nonwoven fabric (thin)P MicaaP PaperQ Silicon R Aramid R RovingsS Synthetic, organicaS Scales, flakesT Talc T CordV VeneerW Wood W Woven fabricX Not specified X Not

45、 specifiedY YarnZ Others Z OthersaThese materials may be further defined by their chemical symbol, for example, or additional symbols defined in the relevant International Standard. In the case of metals (M), it is essential to indicate the type of metal by means of its chemical symbol.bMineral fill

46、ers should be designated more precisely if a symbol is available. Mixtures of materials and/or forms may be indicated by combining the relevant codes using the sign “+” and placing the whole between parentheses. For example, a mixture of 25 % glass fibre (GF) and 10 % mineral power (MD) would be ind

47、icated by (GF25+MD10).4.4 Data block 3In this data block, information about intended application and/or method of processing is given in position 1 and information about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 3. ISO 2018 All right

48、s reserved 3BS EN ISO 205571:2018ISO 20557-1:2018If information is presented in positions 2 to 8 and no specific information is given in position 1 the letter X shall be inserted in position 1.Table 3 Code-letters used in data block 3Code-letter Position 1 Code-letter Positions 2 to 8A Adhesives A P

49、rocessing stabilizedB Blow moulding B AntiblockingC Calendering C ColouredD PowderE Extrusion E ExpandableF Extrusion of films F Special burning characteristicsG General use G GranulesG1 PelletsG3 BeadsH Coating H Heatageing stabilizedK Cable and wire coating K Metal deactivatedL Monofilament extrusion L Light and weather stabilizedM Moulding N Natural (no colour added)P Impact modifiedQ Compression moulding Q1 PlateableR Rotational moulding R Mould release agentS Sintering S Lubrica