HD 620 S1 VOL 1-1996 Distribution Cables with Extruded Insulation for Rated Voltages from 3 6 6 (7 2) kV to 20 8 36 (42) kV (Volume 1 Parts 1 to 5)《额定电压3 6 6(7 .pdf

1、STD.CENELEC HD bSO SL-ENGL Lb ei 3404583 0190175 534 m HARMONIZATION DOCUMENT HD 620 SI DOCUMENT DHARMONISATION (Volume I: Parts 1 to 5) . HARMONISIERUNGSDOKUMENT June 1996 ICs 29.060.20 Descriptors: Electric cable, insulated cable. polyvinyl chloride, polyethylene, designation, composition, dimensi

2、on, construction characteristics, mechanical characteristics, test, marking English version Distribution cables with extruded insulation for rated voltages from 3,6/6 (7,2) kV to 20,8/36 (42) kV Cbles de distribution, isolation extrude, pour des tensions assignes de 3,6/6 (7,Z) kV 20,8/36 (42) kV in

3、clus Energieverteilungskabel mit extrudierter Isolierung fr Nennspannungen von 3,6/6 (7,2) kV bis 20,8/36 (42) kV This Harmonization Document was approved by CENELEC on 1995-1 1-28. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for implem

4、entation of this Harmonization Document on a national level. Up-to-date lists and bibliographical references concerning such national implementation may be obtained on application to the Central Secretariat or to any CENELEC member. This Harmonization Document exists in three official versions (Engl

5、ish, French, German). CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electro

6、technical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Centrai Secretariat: rue de Stassart 35, B - 1050 Brussels o 1996 Copyright reserved to CENELEC member. Ref. No. WD 620 S1:1996 E STD=CENELEC HD b20 SL-ENGL 199b 3404583 OL90L7b

7、 450 m Page 0-2 HD 620 S1:1996 FOREWORD This Harmonisation Document was prepared by WG9 of CENELEC Technical Committee TC20, Electric Cables. It was agreed by TC20 at its Helsinki meeting (May 1994) to be submitted for formal vote by National Committees. The document contains the following Parts, ar

8、ranged according to the main constructional features of the cables covered: Part 1 - Part 3 - Part 4 - Part 5 - Part 6 - Part 7 - Part 8 - Part 9 - General requirements PVC insulated single core cables PVC insulated three core cables XLPE insulated single core cables, and single core pre-assembled c

9、ables XLPE insulated three core cables EPR insulated single core cables and single core pre-assembled cables EPR insulated three core cables HEPR insulated single core cables, and single core pre-assembled cables There is no Part 2, which was to have covered Additional Test Methods. These have been

10、combined with the corresponding Part from HD 622 (Power cables having rated voltage from 3.6/6(7.2)kV up to and including 20.8/36(42)kV with special fire performance for use in power stations) to form Amendment No. 1 to HD 605. Each of Parts 3-9 inclusive are further divided into particular sections

11、 and, by decision of the Technical Board (D68/047) National Committees need at present only implement in their national language those sections having national applicability. The obligation remains however to announce the full HD in public by titles and numbers, and also to withdraw any conflicting

12、national standards. Page numbering reflects the arrangement into Parts and particular sections, e.g. Page 442-3 is page 3 of particular section C of Part 4. References to other HDs, ENS and international standards are given in the particular parts or sections. The draft was submitted to the formal v

13、ote and was approved by CENELEC as HD 620 S1 on 1995-1 1-28. The following dates were fixed: - latest date by which the existance of the HD has to be announced at national level (doa) 1996-06-01 latest date by which the HD has to be implemented at national level by publication of a harmonized nation

14、al standard or by endorsement (dop) 1996-1 2-01 latest date by which the national standards conflicting with the HD have to be withdrawn (daw) 1996-1 2-01 STD.CENELEC HD 620 SL-ENGL L99b 3404583 OL90L77 397 111 Page 0-3 HD 620 S1:1996 CONTENTS Volume I PART 1 General reauirements PART 3 PVC insulate

15、d sinale core cables 3-A 3-C Cables with PVC sheath (Type 3A Cables with PVC sheath (Type 3C) PART 4 PVC insulated three core cables 4-A 4-C Cables with PVC sheath (Type 4A) Cables with PVC sheath (Type 4C) PART 5 XLPE insulated sinale core cables, and sinale core ore-assembled cables 5-A 5-B 5-c 5-

16、D 5-E-1 5-E-2 5-F 5-G 5-H 5-J 5-K 5-L 5-M 5-N 5-0-1 5-0-2 5-0-3 5-0-4 5-0-5 5-0-6 5-P Cables with PE (Type 5A-1) or PVC sheath (Type 5A-2) Cables with PE (Type 5B-1) or PVC sheath (Type 58-21 Cables with PE (Type 5C-1) or PVC sheath (Type 5C-2) Cables with PE (Type 5D-1) or PVC sheath (Type 5D-2) Ca

17、bles with PVC sheath (Type 5E-1) or PVC separation sheath and PVC outer sheath (Type 5E-2) Bundle assembled cables with steel messenger core for overhead distribution and service MV (Type 5E-3) Cables with aluminium conductors and PVC sheath (Type 5F-1 1, cables with aluminium conductors and PE shea

18、th, laid-up (Type 5F-21, cables with aluminium conductors and PE sheath, laid-up around a bare earth conductor (Type 5F-31, cables with aluminium conductors and PE sheath, laid-up around a steel messenger (Type 5F-4) and cables with copper conductors and PVC sheath (Type 5F-5) Cables with PVC sheath

19、 laid-up (Type 5G-11, cables with PVC sheath laid-up around an earth conductor (Type 5G-2 end Type 5G-31, cables with PVC sheath laid around a messenger (Type 5G-4) and cables with PVC sheath not laid-up (Type 5G-5) Cables with PE sheath (Type 5H) Cables with PE (Type 5J-11 or PVC sheath (Type 5J-2)

20、 or PVC flame retardant sheath (Type 5J-31 Cables with PE (Type 5K-1) or PVC sheath (Type 5K-2) Cables with PVC sheath, laid-up (Type 5L-1) or not (Type 5L-2) around an additional conductor Cables with PE sheath (Type 5M-1) and PVC sheath (Type 5M-2) Cables with PE sheath (Type 5N-1) or PVC sheath (

21、Type 5N-2) Single core XLPE insulated cables (Type 50-1) Single core XLPE insulated cables with lead sheath (Type 50-2) XLPE insulated Triplex cables with PE sheath (Type 50-3) Single core XLPE insulated cables with wire screens and PE sheath (Type 50-4) Cables with alternative wire screens and PE s

22、heath (Type 50-5) Single core XLPE insulated cables with wire screens and PVC sheath (Type 50-6) Cables with PVC sheath laid-up around an earth conductor (Type 5P-1 and Type 5P-2), cables with PVC sheath laid around a messenger (Type 5P-3) STD.CENELEC HD 620 SL-ENGL L77b 3404583 0170178 223 Page 0-4

23、 HD 620 S 1 :I 996 CONTENTS Volume II PART 6 XLPE insulated three core cables 6-A 6-C 6-D 6-F 6- J 6-K 6-M 6-N 6-0-1 6-0-2 6-0-3 Cables with PE (Type 6A-1) or PVC sheath (Type 6A-2) Cables with PE (Type 6C-1) or PVC sheath (Type 6C-2) Cables with PE (Type 6D-1) or PVC (Type 60-2) sheath Cables with

24、PVC sheath and individual copper screen (Type 6F-11, cables with PE sheath and individual copper screen (Type 6F-2) and cables with PE sheath and common copper screen (Type 6F-3) Cables with PE (Type 6J-1) or PVC sheath (Type 6J-21 or PVC flame retardant sheth (Type 6J-3) Cables with PE (Type 6K-1)

25、or PVC sheath (Type 6K-2) Cables with PE sheath (Type 6M-1) and PVC sheath (Type 6M-2) Cables with PE sheath (Type 6N-1) or PVC sheath (Type 6N-2) 3-core XLPE insulated cables (Type 60-1 1 3-core XLPE insulated cables with metallic armour and PE sheath (Type 60-2) 3-core XLPE insulated cables with w

26、ire screen and FE screen (Type 60-3) PART 7 gg pre-assembled cables 7-E-1 Cables with PVC sheath (Type 7E-1) 7-E-2 Bundle assembled cables with steel messenger core for overhead distribution and service MV (Type 7E-2) 7-1 Cables with PVC sheath (Type 71) 7-N Cables with PE sheath (Type 7N-1) or PVC

27、sheath (Type 7N-2) 7-0-1 Single core EPR insulated cables (Type 70-1 1 7-0-2 EPR insulated Triplex cables with PE sheath (Type 70-2) 7-0-3 Single core EPR insulated cables with wire screens and PE sheath (Type 70-3) 7-0-4 Cables with alternative wire screens and PE sheaths (Type 70-4) PART 8 EPR ins

28、ulated three core cables 8-1 Cables with PVC sheath (Type 81) 8-N Cables with PE sheath (Type 8N-1) or PVC sheath (Type 8N-2) 8-0-1 3-core EPR insulated cables Type 80-1) 8-0-2 3-core EPR insulated cables with metallic armour and PE sheath (Type 80-2) PART 9 HEPR insulated sinale core cables, and si

29、nale core gre-assembled Ca bles 9-1-1 9-1-2 Cables with HEPR insulation, PE sheath and Alumoweld messenger (Aerial cables, Type 91-1 1 Cables with HEPR insulation and PVC sheath, single core and pre-assembled type (Type 91-21 STD.CENELEC HD 620 SI-ENGL 1996 3404583 0170179 LbT Page 1-1 HD 620 S1:199

30、6 Part 1 HD 620 S1:1996 DISTRIBUTION CABLES WITH EXTRUDED INSULATION FOR RATED VOLTAGES FROM 3.6/6 (7.2) kV UP TO AND INCLUDING 20.8/36 (42) kV PART 1 - GENERAL REQUIREMENTS STD-CENELEC HD b20 SL-ENGL L99b 3404583 OLOL80 981 Page 1-2 HD 620 S1:1996 Part 1 CONTENTS PAGE 1. 2. 3. 4. 5. 6. 7. 8. Genera

31、l 1.1 Scope 1.2 Object Definitions 2.1 2.2 2.3 Rated voltage Marking 3.1 Indication of origin 3.2 Additional marking 3.3 Durability 3.4 Legibility 3.5 Common marking 3.6 Construction of cables Definitions concerning the insulation and sheathing compounds Definitions relating to the tests Use of the

32、name CENELEC 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.1 1 Conductors Insulation Screening of cores Assembly of cores I Fillers and binder tapes Inner covering (bedding) Inner sheath Metallic coverings Outer sheath Earthing conductor Messenger Tests on completed cables Sealing and packing Current-c

33、arrying capacity Guide to use and selection of cables 1-4 1-4 1-5 1-5 1-6 1-6 1-7 1-7 1-7 1-7 1-8 1-8 1-8 1-9 1-10 1-10 1-10 1-1 1 1-12 1-12 1-13 1-13 1-14 1-14 1-14 1-14 1-15 Tables 1-5 Page 1-3 HD 620 S1:1996 Part 1 REFERENCES Part 1 of HD 620 S1 incorporates by dated or undated reference, provisi

34、ons from other publications. These references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to Part 1 of HD 620 S1 only when incorporated in it by amendment or

35、revision. For undated references the latest edition of the publication referred to applies. EN 6081 1 HO 383 HD 405 HD 605 Common test methods for insulating and sheathing materials of electric cables Conductors of insulated cables (Endorsing IEC 228 and 228A) Tests on electric cables under fire con

36、ditions Electric cables: Additional test methods IEC 229 IEC 287 IEC 840 IEC 885 Tests on cable oversheaths which have a special protective function and are applied by extrusion Calculation of the continuous current rating of cables (100% load factor) Tests for power cables with extruded insulation

37、for rated voltages above 30kV (U, = 36 kV) up to 150 kV (U, = 170kV) Electrical test methods for electric cables STD-CENELEC HD b20 SL-ENGL L99b 3404583 03701182 754 Page 1-4 HD 620 S1:1996 Part 1 1. General 1.1 Scope HD 620 aF lies to cables with extruded insulation and for rated voltages U, /U(U,)

38、 from 3.6/ (7.21 kV up to 20.8/36(42) kV used in power distribution systems of voltages not exceeding the maximum r.m.s. value of the system voltage U,. This Part (Part 1) specifies the general requirements applicable to these cables, unless otherwise specified in the particular sections of this HD.

39、 Test methods specified are given in EN 6081 1, HD 383, HD 405, HD 605 and in IEC Publications 229, 840, 885-2 and 885-3. Attention should be drawn to the fact that a significant number of sections include references to long term tests which are collected in HD 605. These long term tests are conside

40、red as necessary and reflect the best available knowledge for the existing cable design. They are related to specific designs and different philosophies concerning adequate measures against the influence of water. However it is the firm intention to reduce this large number of different tests, but m

41、ore experience should be gained before starting to rationalise this important matter. The particular types of cables are specified in Parts 3 to 9. 1.2 Object The objects of this Harmonisation Document are: - to standardise cables that are safe and reliable when properly used, in relation to the tec

42、hnical requirements of the system of which they form a part; - to state the characteristics and manufacturing requirements which have a direct or indirect bearing on safety; - and to specify methods for checking conformity with those requirements. 2. STD.CENELEC HD b20 SL-ENGL L99b W 3404583 0190183

43、 690 9 Page 1-5 HD 620 S1:1996 Part 1 Definitions 2.1 Definitions concerning the insulating and sheathing compounds 2.1 .1 Insulating and sheathing compounds Insulation Sheathing The types of insulating and sheathing compounds covered by this HD are listed below, together with their abbreviated desi

44、gnations: Table 2.1.1 : Insulating and sheathing compounds Insulating and sheathing compounds See: Thermoplastic: Insulating compounds based on: Polyvinyl chloride b Cross-linked: Insulating compounds based on: - Cross-linked polyethylene (XLPE1 - Ethylene propylene rubber (EPR) - Hard ethylene prop

45、ylene rubber (HEPRI (under consideration) a) Elastomeric : bl Thermoplastic: Sheathing compounds based on: - Polyvinyl chloride (PVC) - Polyethylene (PE) Table 2A Table 2B Table 2C (Table 31 Table 4A Table 48 2.1.2 Type of compound The category in which a compound is placed according to its properti

46、es is determined by specific tests. The type designation is not directly related to the composition of the compound. 2.2 Definitions relating to the tests NOTE: Tests classified as Sample (S) or Routine (RI may be required as part of any type approval schemes. 2.2.1 Type Tests (Symbol T1 Tests requi

47、red to be made before supplying a type of cable covered by this HD on a general commercial basis in order to demonstrate satisfactory performance characteristics to meet the intended application. These tests are of such a nature that, after they have been made, they need not be repeated unless chang

48、es are made in the cable material, design or type of manufacturing process which might change the performance characteristics. STD.CENELEC HD b20 SL-ENGL Lb 3404583 OLOL84 527 Page 1-6 HD 620 S1:1996 Part 1 2.2.2 Sample tests (Symbol S) Tests made on samples of completed cable, or components taken f

49、rom a completed cable adequate to verify that the finished product meets the design specifications. 2.2.3 Routine tests (Symbol RI Tests made on all production cable lengths to demonstrate their integrity. 2.2.4 Tests after installation Tests intended to demonstrate the integrity of the cable and its accessories as installed. 2.3 Rated voltage The rated voltage of a cable is the reference voltage for which the cable is designed, and which serves to define the electrical tests. The rated voltage is expressed by the combination of the following values U,/U(U,) expressed